Nice !
only getting really low hash rate though what are the best setting I have not put any just trying to find them. Just thought I would see if it worked 1st
Topic: ANTMINER U3 Discussion and Support Thread - page 13. (Read 149480 times)
Nice !
Ahah !!!
Well it looks like a power supply issue.
Try powering it from a standard power supply
http://thumbs.ebaystatic.com/images/g/VS8AAOSwwE5WYuoS/s-l225.jpg
Well it looks like a power supply issue.
Try powering it from a standard power supply
http://thumbs.ebaystatic.com/images/g/VS8AAOSwwE5WYuoS/s-l225.jpg
those are the types of plugs i use to power up my u3's. plugged into an evga 550w psu.
Ahah !!!
Well it looks like a power supply issue.
Try powering it from a standard power supply
Well it looks like a power supply issue.
Try powering it from a standard power supply
those are the types of plugs i use to power up my u3's. plugged into an evga 550w psu.
Good,
Use that cable, it should work
I have 3 with original power brick and 3 with a pcie (converted to molex) cable.
Use that cable, it should work
I have 3 with original power brick and 3 with a pcie (converted to molex) cable.
If you bought it "new" it should have come with a power brick and USB cable, they are packaged that way from Bitmain. Don't use the factory psu if you are overclocking, though, they tend to melt down. Contact the seller and ask them to send it to you or to refund you part of the purchase price since it appears they may not have sold you a new device.
Or get a molex to barrel plug connector and power the U3 with a standard ATX psu (which is what most people do and what is recommended, I use the same psu that runs my S3+ to also power my U3).
Or get a molex to barrel plug connector and power the U3 with a standard ATX psu (which is what most people do and what is recommended, I use the same psu that runs my S3+ to also power my U3).
I bought it has new from a supplier in Germany from Amazon I'm in Spain and it does say no power supply included but did not see it until it was too late. It did have the cable to power from a ATX psu but did not know until it arrived so I bought a a power brick has the supplier recommended but not worked.
I will go and buy a atx psu tomorrow and try it.
If you bought it "new" it should have come with a power brick and USB cable, they are packaged that way from Bitmain. Don't use the factory psu if you are overclocking, though, they tend to melt down. Contact the seller and ask them to send it to you or to refund you part of the purchase price since it appears they may not have sold you a new device.
Or get a molex to barrel plug connector and power the U3 with a standard ATX psu (which is what most people do and what is recommended, I use the same psu that runs my S3+ to also power my U3).
Or get a molex to barrel plug connector and power the U3 with a standard ATX psu (which is what most people do and what is recommended, I use the same psu that runs my S3+ to also power my U3).
What power supply are you using? Did it ever hash before? You may have burned out the factory psu, or it may be dead.
I bought a 12v 6a power supply brick. I only bought the Antminer new from Amazon it arrived Saturday but with no power supply so was told to buy a 12v 6a power supply which I did.
Ahah !!!
Well it looks like a power supply issue.
Try powering it from a standard power supply
http://thumbs.ebaystatic.com/images/g/VS8AAOSwwE5WYuoS/s-l225.jpg
Well it looks like a power supply issue.
Try powering it from a standard power supply
http://thumbs.ebaystatic.com/images/g/VS8AAOSwwE5WYuoS/s-l225.jpg
thanks for your help sorry for the questions I thought I was doing something wrong and was getting really frustrated.
I was told by the company I bought it from to buy a 12v 6a supply which I did but will try and find another one will keep you up to date I'm running it on a laptop so what would you recommend
What power supply are you using? Did it ever hash before? You may have burned out the factory psu, or it may be dead.
Ahah !!!
Well it looks like a power supply issue.
Try powering it from a standard power supply
Well it looks like a power supply issue.
Try powering it from a standard power supply
H wrote that he did.
And cgminer sees 1 device:
cgminer -n
[2015-12-20 23:19:40] USB all: found 7 devices - listing known devices
.USB dev 0: Bus 2 Device 2 ID: 10c4:ea60
Manufacturer: 'Silicon Labs'
Product: 'CP2102 USB to UART Bridge Controller'
[2015-12-20 23:19:41] 1 known USB devices
Another question:
Is the fan turning ?
no nothing just the 1 led from usb And cgminer sees 1 device:
cgminer -n
[2015-12-20 23:19:40] USB all: found 7 devices - listing known devices
.USB dev 0: Bus 2 Device 2 ID: 10c4:ea60
Manufacturer: 'Silicon Labs'
Product: 'CP2102 USB to UART Bridge Controller'
[2015-12-20 23:19:41] 1 known USB devices
Another question:
Is the fan turning ?
H wrote that he did.
And cgminer sees 1 device:
cgminer -n
[2015-12-20 23:19:40] USB all: found 7 devices - listing known devices
.USB dev 0: Bus 2 Device 2 ID: 10c4:ea60
Manufacturer: 'Silicon Labs'
Product: 'CP2102 USB to UART Bridge Controller'
[2015-12-20 23:19:41] 1 known USB devices
Another question:
Is the fan turning ?
And cgminer sees 1 device:
cgminer -n
[2015-12-20 23:19:40] USB all: found 7 devices - listing known devices
.USB dev 0: Bus 2 Device 2 ID: 10c4:ea60
Manufacturer: 'Silicon Labs'
Product: 'CP2102 USB to UART Bridge Controller'
[2015-12-20 23:19:41] 1 known USB devices
Another question:
Is the fan turning ?
if you're using the cgminer from bitmain website it seems to only recognize 1 antminer u3.
go with the updated version 4.9.2 and it recognizes it fine.
remember that the commands to enter the frequencies and voltages are different from the older versions of cgminer. in 4.9.2 it's different.
I'm only getting 1 led on is there something wrong with the power supply?go with the updated version 4.9.2 and it recognizes it fine.
remember that the commands to enter the frequencies and voltages are different from the older versions of cgminer. in 4.9.2 it's different.
I bought it from amazon but was new but no power supply I had to buy one 12v 6a
tried all versions and still saying no devices detected
if you're using the cgminer from bitmain website it seems to only recognize 1 antminer u3.
go with the updated version 4.9.2 and it recognizes it fine.
remember that the commands to enter the frequencies and voltages are different from the older versions of cgminer. in 4.9.2 it's different.
I'm only getting 1 led on is there something wrong with the power supply?go with the updated version 4.9.2 and it recognizes it fine.
remember that the commands to enter the frequencies and voltages are different from the older versions of cgminer. in 4.9.2 it's different.
I bought it from amazon but was new but no power supply I had to buy one 12v 6a
tried all versions and still saying no devices detected
if you're using the cgminer from bitmain website it seems to only recognize 1 antminer u3.
go with the updated version 4.9.2 and it recognizes it fine.
remember that the commands to enter the frequencies and voltages are different from the older versions of cgminer. in 4.9.2 it's different.
go with the updated version 4.9.2 and it recognizes it fine.
remember that the commands to enter the frequencies and voltages are different from the older versions of cgminer. in 4.9.2 it's different.
You should have 2 Red led
1 close to the usb port
1 "opposite"
To the right of the 2nd one is the red led that blink when hashing.
Is it the 2nd LED that is ON or the 3rd one ?
1 close to the usb port
1 "opposite"
To the right of the 2nd one is the red led that blink when hashing.
Is it the 2nd LED that is ON or the 3rd one ?
I only have one led on
the one close to the usb
You should have 2 Red led
1 close to the usb port
1 "opposite"
To the right of the 2nd one is the red led that blink when hashing.
Is it the 2nd LED that is ON or the 3rd one ?
1 close to the usb port
1 "opposite"
To the right of the 2nd one is the red led that blink when hashing.
Is it the 2nd LED that is ON or the 3rd one ?
just done that again and get the same
whatever I try still keep getting the same result
no devices detected!
Waiting for USB hotplug devices or press q to quit
whatever I try still keep getting the same result
no devices detected!
Waiting for USB hotplug devices or press q to quit
just reading the readme it say
ANTMINER U1/U2+/U3 devices
Antminer devices need the --enable-icarus option when compiling cgminer.
Currently the U1/2/3 USB sticks are supported and come up as the following
devices:
ANU: Antminer U1/U2/U2+
AU3: Antminer U3
but it says
\cgminer>cgminer --enable-icarus
[2015-12-21 16:22:14] cgminer: --enable-icarus: unrecognized option
Sorry I'm I missing something?
ANTMINER U1/U2+/U3 devices
Antminer devices need the --enable-icarus option when compiling cgminer.
Currently the U1/2/3 USB sticks are supported and come up as the following
devices:
ANU: Antminer U1/U2/U2+
AU3: Antminer U3
but it says
\cgminer>cgminer --enable-icarus
[2015-12-21 16:22:14] cgminer: --enable-icarus: unrecognized option
Sorry I'm I missing something?
that's a compile commande, not a running command
just run cgminer --benchmark to see if it's recognized and hashing
then run cgminer and input your pool options
Jump to: