ASICPuppy.net - Terminus, Moonlander 2, 2pacs in Stock! BTC,LTC,ETH,BCH

vickersja

member

Activity: 224

Merit: 34

To be the man, you gotta beat the man...... WOOOOO

Quote from: CrazyGuy on December 28, 2015, 10:27:52 PM

I've sold out of R1's, and as promised, I am releasing my customized firmware to the community. Please note that although I refer to this package as custom firmware, it is really just a patch file. If you reset your R1 to factory defaults, you will lose the customizations. In which case, you would just need to re-apply the patch.

Changelog for release 0.95:
- Opened up port 4029 for API access to cgminer-u3 instance
- Max frequency for U3 increased to 250M
- Max fequency for R1 increased to 250M (I have not personally tested freq past 125. Use at your own risk!)

Firmware Enhancements
- U3 zombie handling(Scripted auto-cgminer restarts and R1 reboot if necessary)
- Supports modifying R1 pools from UI, without losing the ability to use Bitmain's solo pool for R1.
- Detailed R1 stats page, including pool statistics
- Supports modifying R1 freq and voltage from UI
- U3 freq selection increased to 250M
- Cgminer-U3 API open for monitoring with 3rd party tools

WARNING: These customizations provide the ability to push your R1 beyond its intended limits. Because of this, it will likely void your warranty with Bitmain. Additionally, I provide this patch with no official support, and take no responsibility for any damage done to your R1 device or its surroundings. Use at your own risk! By downloading and applying this patch, the user is accepting these conditions.

Download Below
R1CGCustomFW_0.95_2015-12-28.tar.gz

Upgrade instructions
To upgrade your firmware, go to "Backup / Flash Firmware" under the "System" tab
- Click on the "Chose File" button to the right of "Restore Backup:" (NOTE: Do not mistake this with the "Chose File" button under Flash new firmware. - This is not a full binary firmware file)
- Choose "R1CGCustomFW_0.95_2015-12-28.tar.gz" from your PC and then click on the "Upload archive" button.

Your antrouter system will reboot and come back up with updated firmware!

Got this up and running on my Antrouter R1 - Trying on a few solo pools, but I am not getting any accepted shares in the dashboard.

HagssFIN

legendary

Activity: 2506

Merit: 1714

Electrical engineer. Mining since 2014.

@cmccue49
Is your Antminer R1 model the one which can do Bitcoin mining?
I guess that firmware update is created for the R1 Bitcoin model.

cmccue49

newbie

Activity: 19

Merit: 0

Quote from: Buchi-88 on January 09, 2021, 10:30:22 AM

Quote from: CrazyGuy on May 17, 2014, 12:15:13 AM

R1 Custom Firmware available!

As promised, I am releasing my customized firmware to the community. Please note that although I refer to this package as custom firmware, it is really just a patch file. If you reset your R1 to factory defaults, you will lose the customizations. In which case, you would just need to re-apply the patch.

Changelog for release 0.95:
- Opened up port 4029 for API access to cgminer-u3 instance
- Max frequency for U3 increased to 250M
- Max fequency for R1 increased to 250M (I have not personally tested freq past 125. Use at your own risk!)

Firmware Enhancements
- U3 zombie handling(Scripted auto-cgminer restarts and R1 reboot if necessary)
- Supports modifying R1 pools from UI, without losing the ability to use Bitmain's solo pool for R1.
- Detailed R1 stats page, including pool statistics
- Supports modifying R1 freq and voltage from UI
- U3 freq selection increased to 250M
- Cgminer-U3 API open for monitoring with 3rd party tools

WARNING: These customizations provide the ability to push your R1 beyond its intended limits. Because of this, it will likely void your warranty with Bitmain. Additionally, I provide this patch with no official support, and take no responsibility for any damage done to your R1 device or its surroundings. Use at your own risk! By downloading and applying this patch, the user is accepting these conditions.

Download Below
R1CGCustomFW_0.95_2015-12-28.tar.gz

Upgrade instructions
To upgrade your firmware, go to "Backup / Flash Firmware" under the "System" tab
- Click on the "Chose File" button to the right of "Restore Backup:" (NOTE: Do not mistake this with the "Chose File" button under Flash new firmware. - This is not a full binary firmware file)
- Choose "R1CGCustomFW_0.95_2015-12-28.tar.gz" from your PC and then click on the "Upload archive" button.

Your antrouter system will reboot and come back up with updated firmware!

At your Firmware i also can modified the diff manually or i can fix the diff at a sha256 Altcoin pool?

Hi good evening, how are you? The firmware update for the antrouter r1 does not seem to work. I did the proper install. Tried 4 times. Nothing takes. So is this still active? Thank you!

Buchi-88

legendary

Activity: 4004

Merit: 2702

Quote from: CrazyGuy on May 17, 2014, 12:15:13 AM

R1 Custom Firmware available!

As promised, I am releasing my customized firmware to the community. Please note that although I refer to this package as custom firmware, it is really just a patch file. If you reset your R1 to factory defaults, you will lose the customizations. In which case, you would just need to re-apply the patch.

Changelog for release 0.95:
- Opened up port 4029 for API access to cgminer-u3 instance
- Max frequency for U3 increased to 250M
- Max fequency for R1 increased to 250M (I have not personally tested freq past 125. Use at your own risk!)

Firmware Enhancements
- U3 zombie handling(Scripted auto-cgminer restarts and R1 reboot if necessary)
- Supports modifying R1 pools from UI, without losing the ability to use Bitmain's solo pool for R1.
- Detailed R1 stats page, including pool statistics
- Supports modifying R1 freq and voltage from UI
- U3 freq selection increased to 250M
- Cgminer-U3 API open for monitoring with 3rd party tools

WARNING: These customizations provide the ability to push your R1 beyond its intended limits. Because of this, it will likely void your warranty with Bitmain. Additionally, I provide this patch with no official support, and take no responsibility for any damage done to your R1 device or its surroundings. Use at your own risk! By downloading and applying this patch, the user is accepting these conditions.

Download Below
R1CGCustomFW_0.95_2015-12-28.tar.gz

Upgrade instructions
To upgrade your firmware, go to "Backup / Flash Firmware" under the "System" tab
- Click on the "Chose File" button to the right of "Restore Backup:" (NOTE: Do not mistake this with the "Chose File" button under Flash new firmware. - This is not a full binary firmware file)
- Choose "R1CGCustomFW_0.95_2015-12-28.tar.gz" from your PC and then click on the "Upload archive" button.

Your antrouter system will reboot and come back up with updated firmware!

At your Firmware i also can modified the diff manually or i can fix the diff at a sha256 Altcoin pool?

Dreamrace

newbie

Activity: 15

Merit: 5

Hi,

Are you still trading? I have an order in the system pending.

Invoice #100001729.

bencehavran

newbie

Activity: 8

Merit: 0

Hey,

i have bought a used Antrouter R1-BTC, but i have tried with 3 different pool, it does not start to mine.... Stucked on 0 Gh/s Sad

https://i.imgur.com/ZtFIrDS.png

I have made an update also, nothing changed.... does anybody know why?

Thanks

CrazyGuy

legendary

Activity: 1973

Merit: 1007

Black Friday sale today @ ASICPUPPY.COM. Use Promo Code: "BLACKFRIDAY" for 15% off your order.

I've got Newpac and FB Moonlander 2 units in stock!

CrazyGuy

legendary

Activity: 1973

Merit: 1007

Quote from: maxfunky on November 23, 2018, 03:07:54 AM

Quote from: CrazyGuy on May 17, 2014, 12:15:13 AM

R1 Custom Firmware available!

As promised, I am releasing my customized firmware to the community. Please note that although I refer to this package as custom firmware, it is really just a patch file. If you reset your R1 to factory defaults, you will lose the customizations. In which case, you would just need to re-apply the patch.

Changelog for release 0.95:
- Opened up port 4029 for API access to cgminer-u3 instance
- Max frequency for U3 increased to 250M
- Max fequency for R1 increased to 250M (I have not personally tested freq past 125. Use at your own risk!)

Firmware Enhancements
- U3 zombie handling(Scripted auto-cgminer restarts and R1 reboot if necessary)
- Supports modifying R1 pools from UI, without losing the ability to use Bitmain's solo pool for R1.
- Detailed R1 stats page, including pool statistics
- Supports modifying R1 freq and voltage from UI
- U3 freq selection increased to 250M
- Cgminer-U3 API open for monitoring with 3rd party tools

WARNING: These customizations provide the ability to push your R1 beyond its intended limits. Because of this, it will likely void your warranty with Bitmain. Additionally, I provide this patch with no official support, and take no responsibility for any damage done to your R1 device or its surroundings. Use at your own risk! By downloading and applying this patch, the user is accepting these conditions.

Download Below
R1CGCustomFW_0.95_2015-12-28.tar.gz

Upgrade instructions
To upgrade your firmware, go to "Backup / Flash Firmware" under the "System" tab
- Click on the "Chose File" button to the right of "Restore Backup:" (NOTE: Do not mistake this with the "Chose File" button under Flash new firmware. - This is not a full binary firmware file)
- Choose "R1CGCustomFW_0.95_2015-12-28.tar.gz" from your PC and then click on the "Upload archive" button.

Your antrouter system will reboot and come back up with updated firmware!

Great work, is there a similar firmware for the R1-LTC ? Roll Eyes

I haven't fired up an R1-LTC in a while, but if I recall correctly, they now allow you to setup pool information. Didn't see any need for modifying the firmware.

maxfunky

full member

Activity: 194

Merit: 100

Quote from: CrazyGuy on May 17, 2014, 12:15:13 AM

R1 Custom Firmware available!

As promised, I am releasing my customized firmware to the community. Please note that although I refer to this package as custom firmware, it is really just a patch file. If you reset your R1 to factory defaults, you will lose the customizations. In which case, you would just need to re-apply the patch.

Changelog for release 0.95:
- Opened up port 4029 for API access to cgminer-u3 instance
- Max frequency for U3 increased to 250M
- Max fequency for R1 increased to 250M (I have not personally tested freq past 125. Use at your own risk!)

Firmware Enhancements
- U3 zombie handling(Scripted auto-cgminer restarts and R1 reboot if necessary)
- Supports modifying R1 pools from UI, without losing the ability to use Bitmain's solo pool for R1.
- Detailed R1 stats page, including pool statistics
- Supports modifying R1 freq and voltage from UI
- U3 freq selection increased to 250M
- Cgminer-U3 API open for monitoring with 3rd party tools

WARNING: These customizations provide the ability to push your R1 beyond its intended limits. Because of this, it will likely void your warranty with Bitmain. Additionally, I provide this patch with no official support, and take no responsibility for any damage done to your R1 device or its surroundings. Use at your own risk! By downloading and applying this patch, the user is accepting these conditions.

Download Below
R1CGCustomFW_0.95_2015-12-28.tar.gz

Upgrade instructions
To upgrade your firmware, go to "Backup / Flash Firmware" under the "System" tab
- Click on the "Chose File" button to the right of "Restore Backup:" (NOTE: Do not mistake this with the "Chose File" button under Flash new firmware. - This is not a full binary firmware file)
- Choose "R1CGCustomFW_0.95_2015-12-28.tar.gz" from your PC and then click on the "Upload archive" button.

Your antrouter system will reboot and come back up with updated firmware!

Great work, is there a similar firmware for the R1-LTC ? Roll Eyes

eljaydub

newbie

Activity: 3

Merit: 0

Just got my replacement Moonlander 2 in the mail - thank you very much!

eljaydub

newbie

Activity: 3

Merit: 0

Just sent you an email - I ordered a Moonlander 2 on March 7 and still have not received it.

CrazyGuy

legendary

Activity: 1973

Merit: 1007

Due to popular demand, I've added paypal payments back on the site.

CrazyGuy

legendary

Activity: 1973

Merit: 1007

I have a few Terminus units left in stock, as well as Futurebit moonlander 2's and 2pacs. All prices have been lowered to accommodate the falling exchange rate and I have upped the purchase limit on FBM and 2pac to 4 per buyer.

crypto_curious

full member

Activity: 933

Merit: 175

CrazyGuy,

21 of February I ordered Moonlander. Order no #100001492

Since then, it's been travelling between US and France, It's already been in Paris twice. I don't know what is wrong with the address or the way package as been made, but you are only one who can contact USPS, as you have shipper details, I tried.

https://screenshots.firefox.com/gj2id4zw7jiOLg8C/tools.usps.com

Please contact USPS and sort this out please.

CrazyGuy

legendary

Activity: 1973

Merit: 1007

Offering Terminus with custom minera image and rpi with latest vthoang build. Select the corresponding add-on via the order page.

CrazyGuy

legendary

Activity: 1973

Merit: 1007

I have a very small amount of Terminus units in stock. Limit one per customer.

I've created a modular tray design for the Terminus, 12v PSU and rpi which should make them easier/neater to run in larger quantities. I'll include the case for free on the first 3 orders.

crypto_curious

full member

Activity: 933

Merit: 175

Crazyguy, I send some requests via web form, are you able to reply?
It's about two of my orders I made on your website. Please check. Thanks

monkeyrocker

newbie

Activity: 6

Merit: 0

Hello,

I've ordered my units back in december, the pre-order for 2 future moonlanders 2 from asicpuppy.com
I did receive a notification "shipping label created" from USPS but no updates after that and USPS shows its still pending/waiting for the items.
So far no reply through the contact form of asicpuppy and their support email address they list ([email protected]) get returned immediately as non-existing.
Anything @crazyguy can look into?

Thanks in advance,
MR

[EDIT: They were able to get in contact, USPS probably screwed up, should hopefully be sorted now, will update when it arrives]

crypto_curious

full member

Activity: 933

Merit: 175

Yesterday I received my 3 units from Asicpuppy.net.
Well packaged and secured. I assembled heatsinks and fan. Now, they hashing away nicely in my PC, with 756 clock.

Code:

 bfgminer version 5.4.2-38-g106390a99 - Started: [2018-02-04 09:13:17] - [  0 days 01:21:14]
 [M]anage devices [P]ool management [S]ettings [D]isplay options                                          [H]elp [Q]uit
 Pool 0: litecoinpool.org    Diff:3m  +Strtm  LU:[10:34:28]  User:x
 Block: ...bca9ddd1dbdfeb87  Diff:4.16M (29.78Th)  Started: [10:33:39]  I: 2.02uBTC/hr
 ST:5  F:0  NB:31  AS:0  BW:[ 86/ 93 B/s]  E:0.03  BS:7
 3            | 13.11/12.62/12.53Mh/s | A:3712 R:5+0(.13%) HW:151/.52%
------------------------------------------------------------------------------------------------------------------------
 MLD 0:       |  4.79/ 4.32/ 4.29Mh/s | A:1233 R:1+0(.08%) HW: 42/.42%
 MLD 1:       |  4.51/ 4.28/ 4.30Mh/s | A:1294 R:2+0(.15%) HW: 53/.54%
 MLD 2:       |  4.16/ 4.31/ 4.21Mh/s | A:1192 R:2+0(.17%) HW: 59/.62%
------------------------------------------------------------------------------------------------------------------------
 [2018-02-04 10:34:00] Accepted 00b37774 MLD 2  Diff 5m/3m
 [2018-02-04 10:34:01] Accepted 00f86f41 MLD 1  Diff 4m/3m
 [2018-02-04 10:34:03] Accepted 00621284 MLD 2  Diff 10m/3m
 [2018-02-04 10:34:04] Accepted 009bd2f1 MLD 0  Diff 6m/3m
 [2018-02-04 10:34:05] Accepted 00ffb60f MLD 2  Diff 3m/3m
 [2018-02-04 10:34:07] Accepted 00a8c9ee MLD 2  Diff 5m/3m
 [2018-02-04 10:34:08] Accepted 00472747 MLD 1  Diff 14m/3m
 [2018-02-04 10:34:13] Accepted 008f1d2b MLD 0  Diff 6m/3m
 [2018-02-04 10:34:14] Accepted 0077a310 MLD 0  Diff 8m/3m
 [2018-02-04 10:34:16] Accepted 00b0587d MLD 0  Diff 5m/3m
 [2018-02-04 10:34:16] Accepted 0006c15c MLD 1  Diff 148m/3m
 [2018-02-04 10:34:17] Accepted 00863c65 MLD 2  Diff 7m/3m
 [2018-02-04 10:34:25] Accepted 000d1351 MLD 0  Diff 76m/3m
 [2018-02-04 10:34:25] Accepted 009c2d8b MLD 0  Diff 6m/3m
 [2018-02-04 10:34:25] Accepted 000b2f45 MLD 0  Diff 89m/3m
 [2018-02-04 10:34:25] Accepted 0045e70d MLD 1  Diff 14m/3m
 [2018-02-04 10:34:25] Accepted 00293984 MLD 0  Diff 24m/3m
 [2018-02-04 10:34:26] Accepted 008e9277 MLD 1  Diff 7m/3m
 [2018-02-04 10:34:28] Accepted 00345faf MLD 1  Diff 19m/3m

I left feedback on your profile.
Thanks!

chemistua

newbie

Activity: 9

Merit: 0

It's been almost an hour since I paid. Still waiting for at least 1 conformation to have peace of mind and sleep well.

@CrazyGuy, could you please look into this payment ID CPCA3DI7KMGMCZIJGWNONFOCUX

Topic: ASICPuppy.net - Terminus, Moonlander 2, 2pacs in Stock! BTC,LTC,ETH,BCH (Read 105477 times)