Topic: [Awesome Miner] - Powerful Windows GUI to manage and monitor up to 200000 miners - page 28. (Read 703113 times)

Hi Jim,
Yes. The plan is to have a new development release soon where the new auto-region is used.

Short yes - look in the options.

Here FAQ / Help section
https://support.awesomeminer.com/support/solutions/

Hello,
i just contacted you by mail, before i realised you had a topic here

I see that there are some nicehash users and i'm wondering if awesomeminer can be used to monitor temperature, hashrate and alert me (telegram, sms, etc.) when temperature goes above a selected target or hashrate drops below a certain number ?

i'm note trying to operate my miner through a tool, i just want to use nicehash miner and getting alerted when temperature and hashrate change.

Is it possible with Awesomeminer ?

Hi Patrike,

I'm guessing that a future update will handle this change?

https://www.nicehash.com/blog/post/new-auto-locations-in-nicehash-mining-software-update-now

Regards,
...jim

I think the scenario is the following:
- On Linux, Awesome Miner can only read memory temperature for AMD. For Windows both nVidia and AMD are supported.
- Recent mining software versions for Gminer, Lolminer and T-Rex have found some unofficiall way of reading the nVidia memory temperature on Linux.
- NbMiner and most other mining software cannot report memory temperature for nVidia on Linux
- When you use "Change device order", Awesome Miner will not use the mining software reported temperatures by default. Instead Awesome Miner will use what is available from Awesome Miner itself and also provide a way to set a custom device order.

Please note that "Change device order" is only needed in case you manually need to re-arrange the GPUs - in case Awesome Miner doesn't display the correct hashrate and monitoring details for some reason. In most cases you don't need to enable "Change device order".

When not enabled, you will get the memory temperature for all mining software where it's supported (Gminer, Lolminer, T-Rex).

I will also look into if there is a way to find out how they do read the memory temperature on Linux - as this isn't really public information.

lolMiner 1.48 (ETH+TON) show mem temp only if "Change device order" is unchecked
TREX 0.25.9 (ETH) show mem temp only if "Change device order" is unchecked
NBminer 40.1 (ETH) not show mem temp in both states.

Awesome Miner version 9.3.5

 Features
  - Define colors for miner groups, displayed on the Groups page
  - Properties of both Virtual Groups and Standard Groups can be configured via the Groups page
 Changes
  - Remove Legacy operations from ASIC Tools
 Mining software
  - TeamBlackMiner 1.62
 Correctoins
  - Correction to the use of variables in combination with the Remote Proxy

Thanks for your report. Awesome Miner should be able to figure out and show the details correctly in most cases, without the need of specifying the devices manually. I will look into this case and see how to improve.

Is this with combination of a specific mining software or a general problem?

Hi Patrike, i am not understand, why memory temperature on GPU with GDDR6X memory type will be displayed only if "Change device order" button will be deactivated? Is this a bug or so must be? (linux, hive 0.6-214, AM 9.3.3)
Regards

Thanks for the suggestion. The mining history doesn't keep track of the number of shares per pool for each time interval at the moment. Right now it's only the primary pool that is being recorded and only how much time is being spent on the pools. It isn't possible to integrate this with the current design of the mining history.

You can at any point in time look at the pools and their number of accepted shares and difficulty to confirm where the hashrate is spend. As you can do this at any point in time you should be able to confirm and trust that the firmware takes the stated fee and nothing more. In case you need to verify this over time one possibility would be to do it via the API of the Antminer - where you can get the raw data, do the calculations and confirm the result.

Thanks for the reply. Yes, I need to be able to show that the Dev fee being taken is the stated 2.8%. Any way to add that to the Mining History feature?

Thanks for your question. Are you looking for a way to confirm how much of the hash power that is being used for the dev fee pool?

You should be able to see the difficulty and number of accepted share for all pools, including the dev fee pools. Please note that the dev fee pools have a very low difficulty so the number of shares may be quite high while the actual work spend on these pools are low compared to the work spend on your defined mining pools.

@Patrike,

Any way you could add a way to audit the Dev fee being extracted when running your Awesome Miner (Vnish) antminer firmware? Also do you make any changes to the vnish firmware other than to integrate it into the software?

TYVM

Awesome Miner version 9.3.4

 Features
  - Use of variables when setting Custom Configuration Properties on an ASIC miner
 Changes
  - Consider Whatsminer ASIC miners in sleep mode to be Disconnected
  - Trigger condition for finding miners not hashing has been improved to detect more scenarios
 Mining software
  - Cpu-Miner-Opt 3.19.7
  - Gminer 2.91
  - Lolminer 1.48
  - Nanominer 3.6.0
  - SrbMiner-Multi 0.9.4
  - XmRig 6.17.0
 Corrections
  - Correction to API processing of Gminer dual mining
  - Correction to dual mining coin detection in combination with use with the profit switcher
  - Correction to allow fan adjustments when global fan control has been disabled for a specific host

Awesome Miner is automatically downloading the mining software - but what can happen is that you have some security software or anti-virus software that removes it. For this reason, Awesome Miner will fail to start the mining software as the main executable is simply missing.

Please consider adding an exclusion for the folder in your security software.
C:\Users\rickk\AppData\Local\AwesomeMiner\

The miner is not working. It can't find the phoenixminer.exe. that makes sense because its not there. How can I get this to work?

_______________________________________________________________________________ _______________________

Initialize diagnostics (2)
Starting Diagnostics (30s). Awesome Miner version: 9.3.3
OS: Microsoft Windows 10 Home 64-bit
GPU Details:
  nVidia driver version: 512.15
  nVidia OpenCL Platform ID: 0
  GPUs: RTX 3080

Prerequisites:
  Microsoft .NET Framework: 4.8
  Microsoft VC++ 2013 runtime installed: Yes
  Microsoft VC++ 2015 runtime installed: Yes
  Microsoft VC++ 2017 runtime installed: Yes
  Microsoft VC++ 2019 runtime installed: Yes
Starting Mining Software
Setting up Miner Engine. Instance: 1
Engine Type: PhoenixMiner, Auto Download: True, EnginePath: , CustomExecutable: , DualAlgorithm: Unspecified
Properties: (WindowMode: ConsoleFormat, EngineType: PhoenixMiner, IsProfitMiner: True, RunAsAdmin: False)
====================================================================================================
C:\Users\rickk\AppData\Local\AwesomeMiner\phoenixminer_6.0c_windows_1\PhoenixMiner.exe  -wdog 1 -rmode 0 -cdm 2 -cdmport 4028
Configuration:
POOL: stratum+tcp://daggerhashimoto.usa-west.nicehash.com:3353, WAL: 36BQGsobpoycUZHebf3T4t2FxpkQKUxfnw, PASS: x, PROTO: 4, ALLPOOLS: 1

==========

====================================================================================================
Failed to start miner process: Het systeem kan het opgegeven bestand niet vinden
Failed to start miner in Diagnostics mode
Diagnostics completed

Just in case anyone else gets this issue, Patrike identified it as a problem with my .net framework.  Sadly in Windows 10 there is no way to remove it or re-install and none of the many fixes on the internet worked either.  So the only option was a fresh install of windows, but then decided I may as well try the Windows 11 update, was pretty quick, retained all my settings and files and now everything works normally again.

Unfortunately we don't provide any full mining OS ourselves.

Do awesome miners have a separate OS that I can run like hive OS or a simple mining OS? I don't like running mining software on Windows OS, also this support LHR GPUs?.

Awesome Miner version 9.3.3

 Features
  - Rule action to clear all or acknowledge all notifications
  - Include ASIC error details in miner CSV export
 Changes
  - Updated AMD GPU clocking ranges for Linux
 Mining software
  - Gminer 2.90
  - Lolminer 1.47
 Corrections
  - Corrections to visible tabs for a selected miner
  - Correction to Gminer dual mining worker name
  - Correction to Ethermine pool balance