Block Erupter Tube Sales Information Thread [Round4, Price at <1btc per TH/s] - page 14.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: Blazed on August 30, 2014, 10:28:54 PM

Thanks for trying all of that for me...I will try and buy a new wall adapter, but guessing it is a bad controller. Wonder how long an RMA unit will take...

you have one miner correct? if you had two you could chain it to the other controller. I would say ship it to me and I could run the two but if I recall you have great power prices?

Blazed

legendary

Activity: 2128

Merit: 1119

Quote from: philipma1957 on August 30, 2014, 10:06:25 PM

I will walk over to mine and check it.

I
a) power off the miner.
b) power off the ethernet controller--------i am using 5 volt 1 amp wall wart for this
c) pulled the wire that joins the miner to the controller
d) eth only plugged in I put a 5 volt center pos dc in the eth controller and status lights lite up

So with ethernet cable and a power source those status lights turn on. and with full connections they also turn on.

sounds like rma for that gear.

Thanks for trying all of that for me...I will try and buy a new wall adapter, but guessing it is a bad controller. Wonder how long an RMA unit will take...

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: Blazed on August 30, 2014, 10:05:00 PM

Status lights will not light up, but Ethernet lights up and blinks. It is plugged directly into a Gigabit switch with a known good cable...and yes I have set a static IP in the 192.168.0.* range. Should the status lights be on when the unit is powered up?

I will walk over to mine and check it.

I
a) power off the miner.
b) power off the ethernet controller--------i am using 5 volt 1 amp wall wart for this
c) pulled the wire that joins the miner to the controller
d) eth only plugged in I put a 5 volt center pos dc in the eth controller and status lights lite up

So with ethernet cable and a power source those status lights turn on. and with full connections they also turn on.

sounds like rma for that gear.

Blazed

legendary

Activity: 2128

Merit: 1119

Status lights will not light up, but Ethernet lights up and blinks. It is plugged directly into a Gigabit switch with a known good cable...and yes I have set a static IP in the 192.168.0.* range. Should the status lights be on when the unit is powered up?

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: Blazed on August 30, 2014, 09:47:33 PM

I can not log in to my ethernet controller...I have tried to reset it and same result. The ethernet lights for the NIC light up and blink, but I can not ping it or http:192.168.0.254:8000 it. I have tried 5v and 12v barrel connectors same result. Can I run this miner without the controller in any possible way? None of my status lights turn on when it is powered (is that normal?) Any suggestions on what else to try?

it never lite up? Try plugging it into a giga byte switch via ethernet jack and use a 5 volt positive center dc plug .

I know you are tech savvy enough to have a laptop with a 192.168.0.1 .

I run everything into a dlink router 192.168.0.1
If you are ping at it with a laptop to controller the laptop needs to be 192.168.0.1

Blazed

legendary

Activity: 2128

Merit: 1119

I can not log in to my ethernet controller...I have tried to reset it and same result. The ethernet lights for the NIC light up and blink, but I can not ping it or http:192.168.0.254:8000 it. I have tried 5v and 12v barrel connectors same result. Can I run this miner without the controller in any possible way? None of my status lights turn on when it is powered (is that normal?) Any suggestions on what else to try?

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

This is a shout out to friedcat how about a gui with a rollover pool .. the ethernet controller has no rollover pool. antminer s-3 allows 3 pools. while I sleep if ghash goes down I lose my hash power. Would be nice to have a two pool choice or to at least state your controller does not auto switch pools.

brad1121

newbie

Activity: 45

Merit: 0

I have a board that is completely DOA --- all chips Sad

.

Already arranged to ship it back for RMA. Still sucks.

sjc1490

hero member

Activity: 546

Merit: 500

Quote from: philipma1957 on August 30, 2014, 08:21:15 PM

Quote from: sjc1490 on August 30, 2014, 08:19:41 PM

Quote from: philipma1957 on August 30, 2014, 07:35:50 PM

Quote from: sjc1490 on August 30, 2014, 06:03:49 PM

If anyone can find out how to rma a bad board from FC or Canary's GB please post info here, thanks.

Did you send them each a pm?

I did yesterday as well emailing the customer service address and posting earlier here with no response from anyone as of yet. I have a board that has one bad chain (---) and will only hash 157 out of 205. It's a holiday weekend here so I will give the benefit of the doubt and see if someone responds by Tuesday.

good luck man. i hope they fix it fast.

Thanks, appreciate it.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: sjc1490 on August 30, 2014, 08:19:41 PM

Quote from: philipma1957 on August 30, 2014, 07:35:50 PM

Quote from: sjc1490 on August 30, 2014, 06:03:49 PM

If anyone can find out how to rma a bad board from FC or Canary's GB please post info here, thanks.

Did you send them each a pm?

I did yesterday as well emailing the customer service address and posting earlier here with no response from anyone as of yet. I have a board that has one bad chain (---) and will only hash 157 out of 205. It's a holiday weekend here so I will give the benefit of the doubt and see if someone responds by Tuesday.

good luck man. i hope they fix it fast.

sjc1490

hero member

Activity: 546

Merit: 500

Quote from: philipma1957 on August 30, 2014, 07:35:50 PM

Quote from: sjc1490 on August 30, 2014, 06:03:49 PM

If anyone can find out how to rma a bad board from FC or Canary's GB please post info here, thanks.

Did you send them each a pm?

I did yesterday as well emailing the customer service address and posting earlier here with no response from anyone as of yet. I have a board that has one bad chain (---) and will only hash 157 out of 205. It's a holiday weekend here so I will give the benefit of the doubt and see if someone responds by Tuesday.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: sjc1490 on August 30, 2014, 06:03:49 PM

If anyone can find out how to rma a bad board from FC or Canary's GB please post info here, thanks.

Did you send them each a pm?

sjc1490

hero member

Activity: 546

Merit: 500

If anyone can find out how to rma a bad board from FC or Canary's GB please post info here, thanks.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: klondike_bar on August 30, 2014, 10:30:41 AM

Quote from: JstnPwll on August 30, 2014, 09:21:03 AM

I have a board with dead chips hashing at 126.53GHs (138.24GHs expected). This falls within the free replacement zone. How do we get a board replaced?

10% isnt that far off target - assuming you have to send your board in for RMA first is 12GH worth the time and losing 126GH of mining power for 1-2weeks? 12GH is only worth like $12 - hardly worth the time to dissassemble, package, ship, receive, assemble new board when youll lose out on $5 worth of mining income in the meantime

the 128 out of 138 is the working chip set of stats. he should be more like 201 out of 207 .

the lower number is pretty flakey moves all over on my four boards, but the expected for him 138 is way under the normal expected of 207. that number should be rigid and only move when you change freq say freq 260 = 199 gh, freq 270 = 207gh, freq 280 = 214gh

sidehack

legendary

Activity: 3416

Merit: 1865

Curmudgeonly hardware guy

I can confirm they work on slush (bitcoin.cz) and mmpool (mmpool.org) as well. I'll see about posting our experimental slush proxy mod (which is still in progress) that I've been using to mine on ozcoin successfully for the last 24 hours.

jimmothy

hero member

Activity: 770

Merit: 509

Quote from: klondike_bar on August 30, 2014, 10:30:41 AM

Quote from: JstnPwll on August 30, 2014, 09:21:03 AM

I have a board with dead chips hashing at 126.53GHs (138.24GHs expected). This falls within the free replacement zone. How do we get a board replaced?

10% isnt that far off target - assuming you have to send your board in for RMA first is 12GH worth the time and losing 126GH of mining power for 1-2weeks? 12GH is only worth like $12 - hardly worth the time to dissassemble, package, ship, receive, assemble new board when youll lose out on $5 worth of mining income in the meantime

Each board is supposed to be 200-215 gh/s.

klondike_bar

legendary

Activity: 2128

Merit: 1005

ASIC Wannabe

Quote from: JstnPwll on August 30, 2014, 09:21:03 AM

I have a board with dead chips hashing at 126.53GHs (138.24GHs expected). This falls within the free replacement zone. How do we get a board replaced?

10% isnt that far off target - assuming you have to send your board in for RMA first is 12GH worth the time and losing 126GH of mining power for 1-2weeks? 12GH is only worth like $12 - hardly worth the time to dissassemble, package, ship, receive, assemble new board when youll lose out on $5 worth of mining income in the meantime

JstnPwll

member

Activity: 92

Merit: 10

I have a board with dead chips hashing at 126.53GHs (138.24GHs expected). This falls within the free replacement zone. How do we get a board replaced?

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

I am still using ghash I don't have the time to setup a proxy. It does work nicely with ghash. I have tried different settings and it seems to prefer freq 260 it also uses less power at that setting.

The Be200 gui is really shamefully done only 1 pool no rollover. This was a nice piece of gear and you spoiled it for the miners. I will not sell it I will mine it to death as to resell it with the current gui would be wrong. How about a 2 or 3 pool choice with rollovers in the gui, better yet it came late instead of a coupon or a rebate send out a new controller with a gui that allows for 3 pool choices with auto rollover.

WBF1

sr. member

Activity: 419

Merit: 250

Quote from: helipotte on August 29, 2014, 04:54:49 PM

Quote from: sidehack on August 29, 2014, 04:14:23 PM

I was having issues earlier connecting to slush with one, but it's working beautifully through the modified ckpool proxy. Might try again later and see what was up.

Is this proxy available for download? Cheesy

also wondering this. using BFGminer as proxy gives me particularly high reject rates (although that could be some settings I need to change?).

Topic: Block Erupter Tube Sales Information Thread [Round4, Price at <1btc per TH/s] - page 14. (Read 88194 times)