Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 1151. (Read 6590565 times)

How many GPU's do you have on device manager and what are their status? 

Yep, all 6 cards are using powered risers. 2 risers per SATA PSU cable. Using a EVGA 1600. I've used these risers on 295x2 so I know the risers are good. Same MB and risers rig, just 480 cards. Will not post so can't even troubleshoot further.

Are you using powered risers?  They are needed if running more than 2... maybe 3 cards.  The MB can only supply ~150W to PCIe slots.  Cards can draw up to 75W from the slot (though 66W or less is more recommended...).  It would be an issue, especially if using 6 pin rather than 8 pin PCIe power connector 480s.

Am I doing something wrong? I see many people here running 6 X RX480 on the BTC PRO MB and Win7 and Win10, I have the same setup using powered risers and with 6 cards can't even get to post. Most I got working is 4 cards. I have the MB running 295 X2 GPU, 3 of them for a total of 6 GPU's fine, but no dice with the 480's. Am I missing something?

I would prefer static interface, though currently I like Claymore better than Genoil, it has colors, and better formatting, perhaps it could be an option?  Or some sort of hybrid static/scrolling.

Honestly, I prefer the scrolling

Static interface would be nice!!!

Hi Claymore!

At first - seems that it some built-in temp hysteresis parameter, what was set to 4 degr. At example on my rig, when tt limit set to 65 degr., and temp reach this value, fan begin work on 100%. And it continue working on 100%, till temp downs to 61 degr. It would be fine, if there were active option for temp hysteresis, which user can set manually for better configuration rigs.
And second: are you planning to add static interface, like cgminer or sgminer? When I looking on moving, from down to top, lines with different colours, I worry that I will get epileptic fit . But seriously, moving lines is anachronism from standart ethminer. It's time to make normal static interface.

I am having a problem with one of my rigs it is crashing all the time (sometimes I have to disconnect the power to all GPUs, uninstall the onboard graphics, and then connect the power to all cards again before rebooting the PC to get the PC to boot, and sometimes I even get THREAD_STUCK_IN_DEVICE_DRIVER error message when trying to boot the PC), and I did find out that if I turn off GPU 5 it seems to work better and not crashing.
I am running in Windows 10 x64 with Sappire Radeon RX 480, and I did try different drivers without any luck. And I got the same clock settings on all cards (I am running 4 more RX480 on another machine and that one did not crash one single time in over 3 weeks) This is how the logfile looks right before the crash if I run with GPU 5 on...


02:27:22:161   11f0   ETH: GPU0 27.335 Mh/s, GPU1 27.361 Mh/s, GPU2 27.348 Mh/s, GPU3 27.288 Mh/s, GPU4 27.351 Mh/s, GPU5 0.000 Mh/s
02:27:22:166   11f0    DCR - Total Speed: 2733.663 Mh/s, Total Shares: 319, Rejected: 4
02:27:22:171   11f0    DCR: GPU0 546.709 Mh/s, GPU1 547.214 Mh/s, GPU2 546.966 Mh/s, GPU3 545.762 Mh/s, GPU4 547.012 Mh/s, GPU5 0.000 Mh/s
02:27:22:446   ca0   DCR: weak share, skip
02:27:23:291   6ac   DCR: weak share, skip
02:27:23:761   408   GPU0 t=59C fan=44%, GPU1 t=84C fan=61%, GPU2 t=79C fan=53%, GPU3 t=79C fan=58%, GPU4 t=85C fan=61%, GPU5 t=85C fan=60%
02:27:23:766   408   em hbt: 0, dm hbt: 0, fm hbt: 0,
02:27:23:766   408   watchdog - thread 0, hb time 203
02:27:23:771   408   watchdog - thread 1, hb time 94
02:27:23:771   408   watchdog - thread 2, hb time 0
02:27:23:771   408   watchdog - thread 3, hb time 125
02:27:23:776   408   watchdog - thread 4, hb time 31
02:27:23:776   408   watchdog - thread 5, hb time 141
02:27:23:781   408   watchdog - thread 6, hb time 219
02:27:23:781   408   watchdog - thread 7, hb time 110
02:27:23:786   408   watchdog - thread 8, hb time 94
02:27:23:786   408   watchdog - thread 9, hb time 203
02:27:23:791   408   watchdog - thread 10, hb time 77656
02:27:23:791   408   WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:23:796   408   watchdog - thread 11, hb time 77547
02:27:23:801   408   WATCHDOG: GPU 5 hangs in OpenCL call, exit
02:27:24:806   408   Restarting OK, exit...





This is how my *.bat file looks

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xMyEtherWalletAddress -epsw x -eworker miner2 -dpool stratum+tcp://dcr.coinmine.pl:2222 -dwal MyUsername.miner2 -dpsw MyPassword -dcri 40



What can be wrong, any advice?

What are you guys getting hash rate wise for NVIDIA 1070 dual mining with SIA using Claymore?

to high power consumation on sia+eth  1215w vs 990w 4x390x  eth + sia vs eth solo 1055/1500 -100mv

Ok, will be added in next update.

Claymore, could you do some ethman modification: let ethman show "off" instead gpu temperature of those cards, wich was switched off by max temp reached or another reason

That's what did the trick, thank you, I got the same advice from the dev.

Been playing with some of the more advanced features of the miner.
Temp control, voltage control, etc.
One of my 4 cards gives me this error, how to fix this?

Failed to set new Power Control treshold for GPU #0

del *_log.txt
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu.dwarfpool.com:8008 -ewal 0xxxxxxxxxxx/MiningrigAMD -epsw x -dpool sia.suprnova.cc:7777 -dwal xxxx.gpu -dpsw x -dcoin sia -allpools 1 -powlim -18 -cvddc 1030 -tt -100 -ttdcr 80

Card #0 = a AMD 280x by the way.
Running at Crimson 16.3.2 driver by the way.

Thank you for your time and advice, I found solution with the help of the dev by using -li. That did a nice, fine and silky job ;]

yes, thank you for your time and possible solutions in my issue, i got them nailed. Gaming is out of the question or else I need to drop hashrate even further.

Coinotron pool has auto switch between ETH and ETC to more profit

As opposed to what? Disabling dev fee?

So I run this as my batch file with with exactly that as listed on the dcr.suprnova.cc page. Do I edit my wallet address over the "1" in the "-dwal suprnove.1"?

Also it would seem that eth mining worked with my current ethermine.org in the batch file. I just want to make sure that it isn;t a necessity to run both of those on the suprnova pools.

Do I just use suprnova.1 in the batch file and the decred wallet in the config? Far as suprnova I made a worker but I do not know what to do with that.

edit:
I think I get it. supernova.1 is supposed to be my pool username.workername. Figured it out while trying to get LBRY mining working. I read that there is improper fan and power controls for nvidia dual mining right now so I will get back to this later.