Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 643.

Recnoir

newbie

Activity: 6

Merit: 0

Quote from: parentino on August 25, 2017, 08:35:20 PM

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

Did you apply the atikmdag bios patcher after installing the blockchain driver?

parentino

newbie

Activity: 6

Merit: 0

Hi,just a noob question,just installed latest Beta-Blockchain-Workloads-Aug23,and miner stop working,it reads both cards and than i get "stoped working" messageeverything was just fine with previous crimson 17.xxx,bat file wasnt changed,rolled back to 17.xx version and everything work fine,rlly wanted to try blockhain driver,using claymore 9.8 version on windows 7,cards are rx 470s,any known issues for this cards and driver,thx?

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: NoHash on August 25, 2017, 03:12:31 PM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

How many Watts at the wall?

I have an air that I am headed down to test
Did you mod the voltage? If so, what did you use?

Thanks

I'll bring my watt-meter tomorrow.
I did lower the voltage with wattman.
And again ... 1100 mem gives non-valid shares sometimes in claymore ... need 1080 to be stable ... or more cooling maybe
I'll try to apply additional fan to blow to the card tomorrow too

NoHash

newbie

Activity: 34

Merit: 0

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

How many Watts at the wall?

I have an air that I am headed down to test
Did you mod the voltage? If so, what did you use?

Thanks

greatauror28

full member

Activity: 181

Merit: 101

Ethereum Miner

Quote from: SubZer0 on August 25, 2017, 01:50:05 PM

At nanopool i can only choose Pascal or Sia as a second coin to mine no DCR?
Where do you guys find that option, or is it a other website.
Would like to hear more about this wan't to change from ETH+SIA to this.

Nanopool doesn't support deCRED. You'd have to enter a supernova (or similar) address to mine dcr.

I recently shifted from eth+sia into eth+dcr due to the pitiful earnings I'm getting now from siacoin. And besides, DCR keeps rising in value. I can also attest that with the same -dcri settings, you'd get higher hash rate for DCR than SIA and lower power draw too.

6x Rx580 | Claymore 9.8 | Aug11 Blockchain Drivers | 175.5 ETH 3500 DCR | 115W GPU-Z | DCRI 20

SubZer0

full member

Activity: 274

Merit: 100

At nanopool i can only choose Pascal or Sia as a second coin to mine no DCR?
Where do you guys find that option, or is it a other website.
Would like to hear more about this wan't to change from ETH+SIA to this.

NavyCuda

member

Activity: 107

Merit: 10

Quote from: noviceminer on August 25, 2017, 01:04:52 PM

Quote from: rednoW on August 25, 2017, 12:57:53 PM

Quote from: NavyCuda on August 25, 2017, 12:03:05 PM

Quote from: rednoW on August 25, 2017, 11:46:33 AM

Quote from: NavyCuda on August 25, 2017, 11:30:43 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

I was getting 42.1Mh/s and ~1100Mh/s DCR at 1137cc/1100HBM2. Until it hard crashes... Which I think is related to the block chain driver and Vega FE.

What was the core voltage with this settings?
Pitty, I had to low memclock to 1080mhz because there were some incorrect ETH shares reported by miner.
Now seems ok ... and no single crash yet ...

Have you tried ETH + SIA and other combinations ?

No I have not.

NavyCuda

member

Activity: 107

Merit: 10

Quote from: rednoW on August 25, 2017, 12:57:53 PM

Quote from: NavyCuda on August 25, 2017, 12:03:05 PM

Quote from: rednoW on August 25, 2017, 11:46:33 AM

Quote from: NavyCuda on August 25, 2017, 11:30:43 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

I was getting 42.1Mh/s and ~1100Mh/s DCR at 1137cc/1100HBM2. Until it hard crashes... Which I think is related to the block chain driver and Vega FE.

What was the core voltage with this settings?
Pitty, I had to low memclock to 1080mhz because there were some incorrect ETH shares reported by miner.
Now seems ok ... and no single crash yet ...

I set core voltage with claymore's miner, 1000mV. I needed 1000 or my memory overclock would fall to 800MHz. On vega fe beta drivers, 950Mv.

noviceminer

newbie

Activity: 72

Merit: 0

Quote from: rednoW on August 25, 2017, 12:57:53 PM

Quote from: NavyCuda on August 25, 2017, 12:03:05 PM

Quote from: rednoW on August 25, 2017, 11:46:33 AM

Quote from: NavyCuda on August 25, 2017, 11:30:43 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

I was getting 42.1Mh/s and ~1100Mh/s DCR at 1137cc/1100HBM2. Until it hard crashes... Which I think is related to the block chain driver and Vega FE.

What was the core voltage with this settings?
Pitty, I had to low memclock to 1080mhz because there were some incorrect ETH shares reported by miner.
Now seems ok ... and no single crash yet ...

Have you tried ETH + SIA and other combinations ?

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: NavyCuda on August 25, 2017, 12:03:05 PM

Quote from: rednoW on August 25, 2017, 11:46:33 AM

Quote from: NavyCuda on August 25, 2017, 11:30:43 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

I was getting 42.1Mh/s and ~1100Mh/s DCR at 1137cc/1100HBM2. Until it hard crashes... Which I think is related to the block chain driver and Vega FE.

What was the core voltage with this settings?
Pitty, I had to low memclock to 1080mhz because there were some incorrect ETH shares reported by miner.
Now seems ok ... and no single crash yet ...

NavyCuda

member

Activity: 107

Merit: 10

Quote from: rednoW on August 25, 2017, 11:46:33 AM

Quote from: NavyCuda on August 25, 2017, 11:30:43 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

I was getting 42.1Mh/s and ~1100Mh/s DCR at 1137cc/1100HBM2. Until it hard crashes... Which I think is related to the block chain driver and Vega FE.

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: NavyCuda on August 25, 2017, 11:30:43 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

Definetly not the case when dual-mining. Hashrate decreased significantly.
And the voltage stay the same.
Will get power meter and need some advice howto downvolt below 1v to test low-power modes.

NavyCuda

member

Activity: 107

Merit: 10

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

Drop your clocks to 1137. Same hash rate, much cooler running.

gegstore

member

Activity: 78

Merit: 10

Quote from: TechPark on August 25, 2017, 01:22:49 AM

Quote from: gegstore on August 24, 2017, 10:37:12 PM

Quote from: TechPark on August 24, 2017, 09:33:39 PM

Quote from: gegstore on August 24, 2017, 09:21:29 PM

Quote from: TechPark on August 24, 2017, 09:18:58 PM

Quote from: gegstore on August 24, 2017, 01:32:57 PM

ethman don't work with 9.8 version
help me

It does work for me.
What is your bat/config file?
What is the error message?
Screenshots will be helpful...

no error message but only from other pc i don't see nothing loss connection
with 9.7 i see all

Provide screenshots and config files

i have resolve from myself, windows firewall don't have the miner in the whitelist

i don't can post the screenshot but i repeat with claymore 9.7 all work good

Well... if you do not provide any more information there is nothing to work with...
ETHMAN works for me and I have 9.8

rednoW

legendary

Activity: 1510

Merit: 1003

Quote from: Shnikes101 on August 25, 2017, 10:50:46 AM

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

The card definitely prefers to stay cool. What's your one minute ETH avg.? Good to see you got Memory stable at 1100 - also at 1v? Beta mining drivers or 17.8.1?

HBM2 voltage cannot be changed with now available tools.
I'm using 17.8.2 drivers.
Beta mining drivers caused constant rebooting win7 64 on windows load.

nadrojcote

full member

Activity: 234

Merit: 102

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

That decred hashrate is impressive!

Shnikes101

full member

Activity: 254

Merit: 109

Quote from: rednoW on August 25, 2017, 10:26:28 AM

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

The card definitely prefers to stay cool. What's your one minute ETH avg.? Good to see you got Memory stable at 1100 - also at 1v? Beta mining drivers or 17.8.1?

mizzack

newbie

Activity: 1

Merit: 0

Finally figured out how to reproducibly get undervolts to (mostly) stick on the blockchain drivers with Afterburner and Wattman

1) Apply clocks/volts in Wattman. e.g. 1130/850.
2) Launch AB with no adjustments set. (+0mV)
4) Launch Claymore and wait for the miner to fully kick in. Observe your voltage in AB (that you set in Wattman) get completely ignored.
5) Change your Wattman clocks to, say, 1135Mhz and apply (then back to 1130 and apply). Observe the voltage in AB go back to a static, undervolted clock.
6) Note the ∆ in AB. E.g if I set Wattman to 850mV, it might be reading 937mV in AB.
7) Adjust AB voltage offset but don't bother applying it yet. It won't do anything. So, to go from 937mV actual we'd want -90 offset in AB.
8 ) Stop the miner.
9) Apply AB voltage offset.
10) Launch miner. You'll see your voltages jump up again, so do step #4 again. You should now be pretty close to your desired voltage.[/li][/list]

I've only seen it reset to high voltage occasionally when doing something like turning the monitor on/off. Step #4 resolves it.

With this I'm seeing ~5-10W per card improvement over 17.7.1 dualmining.

rednoW

legendary

Activity: 1510

Merit: 1003

RX Vega 64 Liquid 1560gpu/1100mem@1v gpu core
dualminer 9.8 -dcri 60
55-60 degrees with 3000 rpm

jackbox

legendary

Activity: 1246

Merit: 1024

Quote from: ascaloon on August 25, 2017, 09:39:44 AM

Hello!

Anybody has news about whats the diference between 11th aug and 23th aug relesed blockchain fix driver?

win10-64bit-crimson-relive-beta-blockchain-workloads-aug11.exe
Win10-64Bit-Crimson-ReLive-Beta-Blockchain-Workloads-Aug23.exe

Thanks.

VEGA support added. That's it. It still does not work properly.

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 643. (Read 6590565 times)