Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 796.

Aquazi

full member

Activity: 215

Merit: 100

Something I really dislike about your miner Claymore is the fact that if I'm dual mining ETC, when DevFee starts I lose another 30-40 seconds because it needs to swap to a different DAG and then after DevFee ends it changes again to a different DAG (132 on ETC 130 on ETH).

I really, really dislike it about your miner.

Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.

preda

sr. member

Activity: 756

Merit: 250

Quote from: Vann on June 22, 2017, 08:09:09 AM

Quote from: batmanvip on June 22, 2017, 07:40:23 AM

hi i'm new in mining and have one question:

I have ASUS Z97-PRO with gtx970 (one PSU 750W)

i plan to buy 4x RX580 and one psu 650W gold. its posible to connect to Z97-pro and mining ETH with only rx580s?, because i dont plan make new rig for mining, i need use my computer normaly with gtx970 with no freezes, Its posible?

Go with the 750W or 850W EVGA G2/P2 instead of a 650W. The cost difference between the two is less than $50. The 650W only has two VGA connectors while the 750W has four and the 850W has four 8-pin + two 6-pin pigtail cables. The PSU will also run more efficiently using less of the maximum capacity.

you would plan to buy Grin

but you wont buy because in the world right now they are impossible to buy Shocked

platitude

member

Activity: 103

Merit: 10

Quote from: numeratrix on June 22, 2017, 04:27:35 PM

Does Claymore have alarms build in, and if so for what? I can't figure why the miner is setting off what sounds like a continuous BIOS beep. I stop the miner and the issue stops everytime. Undecided

Last stop point:

Maybe GPU1 overheat can cause that?

numeratrix

newbie

Activity: 15

Merit: 0

Does Claymore have alarms build in, and if so for what? I can't figure why the miner is setting off what sounds like a continuous BIOS beep. I stop the miner and the issue stops everytime. Undecided

Last stop point:

https://i.imgur.com/szb5jnC.png

platitude

member

Activity: 103

Merit: 10

Quote from: Havane on June 22, 2017, 03:35:23 PM

How much lbry hashrate can you have in dual mining with a Rx480?

Thx

https://whattomine.com/
Select LBRY, click on 480 and type: 1, click "Calculate", see the results

Havane

jr. member

Activity: 76

Merit: 3

How much lbry hashrate can you have in dual mining with a Rx480?

Thx

LJLT

newbie

Activity: 48

Merit: 0

Quote from: platitude on June 22, 2017, 10:21:00 AM

Quote from: LJLT on June 22, 2017, 09:31:51 AM

Quote from: LJLT on June 21, 2017, 11:56:37 PM

Hi guys, today i tried ver 9.5 two of my rigss all good. But the third one when i double click the .bat file it opens and close the comand line window in micro seconds.

I already deactivaded the win defender, dont know why this is happening.

Can someone help me.

Thanks

Please guys anyone, one piece of advice...

Copy your .bat file to Claymore directory
Press WIN+R, type: cmd, press ENTER, command prompt should open
Type: cd PATH_TO_CLAYMORE_MINER_DIRECTORY, press ENTER
Type the name of your .bat file and press ENTER, miner should start mining. If you see an error copy/paste it here. PM me if need more help.

Thanks

comp

member

Activity: 112

Merit: 10

Quote from: thameur on June 22, 2017, 01:49:49 PM

any news about the DAG

Yeah curious

thameur

newbie

Activity: 30

Merit: 0

any news about the DAG

Vlizze

newbie

Activity: 46

Merit: 0

Is there a way to output average hashrates instead of instant hashrates? Would make optimizing -dcri a lot easier.

rogeriosmorais

newbie

Activity: 26

Merit: 0

Quote from: rogeriosmorais on June 22, 2017, 06:28:50 AM

Quote from: tytanick on July 10, 2016, 03:21:56 AM

Quote from: GandalfG on July 09, 2016, 07:17:56 PM

Mining with Claymore and get full HDD (128GB SSD) in half hour.
After checking find /var/log/syslog and kern.log grown up to 52GB each.
System write this 4 messages about 4-5 thousands per second !

Code:

Jul 9 23:58:37 test-rig kernel: [ 1399.017519] VM fault (0x01, vmid 6) at page 135290427, read from 'TC3' (0x54433300) (196)
Jul 9 23:58:37 test-rig kernel: [ 1399.017554] amdgpu 0000:04:00.0: GPU fault detected: 147 0x01c84801
Jul 9 23:58:37 test-rig kernel: [ 1399.017557] amdgpu 0000:04:00.0: VM_CONTEXT1_PROTECTION_FAULT_ADDR 0x08105E39
Jul 9 23:58:37 test-rig kernel: [ 1399.017559] amdgpu 0000:04:00.0: VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0C048001

Jul 9 23:58:37 test-rig kernel: [ 1399.017561] VM fault (0x01, vmid 6) at page 135290425, read from 'TC4' (0x54433400) (72)
Jul 9 23:58:37 test-rig kernel: [ 1399.017567] amdgpu 0000:01:00.0: GPU fault detected: 147 0x01f08801
Jul 9 23:58:37 test-rig kernel: [ 1399.017569] amdgpu 0000:01:00.0: VM_CONTEXT1_PROTECTION_FAULT_ADDR 0x08105E3E
Jul 9 23:58:37 test-rig kernel: [ 1399.017570] amdgpu 0000:01:00.0: VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0C088001

Jul 9 23:58:37 test-rig kernel: [ 1399.017572] VM fault (0x01, vmid 6) at page 135290430, read from 'TC6' (0x54433600) (136)
Jul 9 23:58:37 test-rig kernel: [ 1399.017607] amdgpu 0000:04:00.0: GPU fault detected: 147 0x01e84801
Jul 9 23:58:37 test-rig kernel: [ 1399.017610] amdgpu 0000:04:00.0: VM_CONTEXT1_PROTECTION_FAULT_ADDR 0x08105E3D
Jul 9 23:58:37 test-rig kernel: [ 1399.017612] amdgpu 0000:04:00.0: VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0C048001

Despite this mine worked properly 24.3 MH/s on each card until the disk is full

Someone also stumbled upon a similar problem?

System:
Lubuntu 16.04 with amdgpu-pro_16.30.3

5x RX 480 8GB ref model
Asrock FM2A88X + BTC

Hi, i have the same problem in my new project : http://simplemining.net/
Anyway it doesnt bother mining and about logs you can turn then off:
as root execute this command and you will have no longer such problem

systemctl disable rsyslog.service
then delete big file logs from /var/log/ adn reboot system, then it will work fine.
If you want i will release my http://simplemining.net/ Operating System which will have this fix and many more + feature updates.
If you want make donation BTC: 1ERRVbvV23h51ScH73nQr6TDmaieKNuuVD

I'm running into the same problem in simpleMining OS.

1 - My pendrive is not full:

Filesystem Size Used Avail Use% Mounted on
udev 1.9G 0 1.9G 0% /dev
tmpfs 390M 35M 356M 9% /run
/dev/sda2 6.5G 2.1G 4.4G 33% /
tmpfs 2.0G 0 2.0G 0% /dev/shm
tmpfs 5.0M 0 5.0M 0% /run/lock
tmpfs 2.0G 0 2.0G 0% /sys/fs/cgroup
tmpfs 2.0G 8.0K 2.0G 1% /var/log
tmpfs 2.0G 89M 1.9G 5% /var/tmp
tmpfs 300M 16K 300M 1% /tmp
tmpfs 2.0G 0 2.0G 0% /var/log/apt
/dev/sda1 8.9M 3.5K 8.9M 1% /mnt/user
tmpfs 390M 0 390M 0% /run/user/1000

2 - Logs are disabled in claymore

3 - I've executed the sudo systemctl disable rsyslog.service command, didnt help.

4 - It only started to pop up when I plugged in the 3rd card.

5 - My hashing does not seem to be affected by it.

6 - It's a Z270-P Asus Prime MB.

Anyone?

Klexicon

newbie

Activity: 11

Merit: 0

Quote from: Steve_Sanders on June 22, 2017, 02:48:14 AM

Hey guys I've been mining eth+dcr successfully for 12h now (my very first try ever), and i get 14-15 Mh/s on Eth and 145 Mh/s with Dcr with a gtx 1060 3gb.

I pointed the miner to my eth wallet and the dcr to the suprnova pool but while i receive dcr (0,0010 dcr so far) i still see no fractions of eth, is it normal?

Can you share more information on your setup and any settings you may have altered? There's a few of us with the same card who are unable to get the hashrate you are getting.

H0wzer87

newbie

Activity: 2

Merit: 0

Hey guys, noob here, I just set up my first rig with ubuntu. Claymore is starting and finds both test GPUs. But after a few minutes I get following error: miner thread hangs need to restart miner.

Is there any solution to this? what did I set up wrong?

thanks a lot

marine1983

newbie

Activity: 4

Merit: 0

Quote from: draz117 on June 22, 2017, 09:29:53 AM

I downloaded the V9.5 and i keep getting this error for gtx 1060 3gb
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.

You need to set windows page file to 16gb

platitude

member

Activity: 103

Merit: 10

Quote from: LJLT on June 22, 2017, 09:31:51 AM

Quote from: LJLT on June 21, 2017, 11:56:37 PM

Hi guys, today i tried ver 9.5 two of my rigss all good. But the third one when i double click the .bat file it opens and close the comand line window in micro seconds.

I already deactivaded the win defender, dont know why this is happening.

Can someone help me.

Thanks

Please guys anyone, one piece of advice...

Copy your .bat file to Claymore directory
Press WIN+R, type: cmd, press ENTER, command prompt should open
Type: cd PATH_TO_CLAYMORE_MINER_DIRECTORY, press ENTER
Type the name of your .bat file and press ENTER, miner should start mining. If you see an error copy/paste it here. PM me if need more help.

RuMiner

member

Activity: 168

Merit: 15

Quote from: h2gvaka on June 22, 2017, 08:03:13 AM

Can you set Claymore to share mined ETH to two wallets and set how much percentage to send to one and how much to another?

I made a bat file for tihs. it is started via sheduler on saturday and on monday, so I mine monday to friday to one wallet, weekends to another one.
main.txt contains one pool config, safe.txt second config for saturday and sunday (theese files must contain last string empty!)
settings.txt - general miner settings
logdir - your miner path
when started, it detects a weekday and generates config.txt by merging appropriate pool settings and the rest of it

Code:

@echo off
rem Startday ver 1.01
For /F "Skip=1" %%i In ('WMIC Path Win32_LocalTime Get DayOfWeek') Do Set /A $DayOfWeek=%%i+1&GoTo DayOfWeek
:DayOfWeek
Echo Day: %$DayOfWeek%
taskkill -f /im EthDcrMiner64.exe
timeout 10
rem ############################################
set logdir=C:\hal\dual_main
rem ############################################
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
set WORKER=%computername%
del %logdir%\config.txt

if %$DayOfWeek%==1 (
copy %logdir%\safe.txt+%logdir%\settings.txt %logdir%\config.txt /b
) else (
if %$DayOfWeek%==7 (
copy %logdir%\safe.txt+%logdir%\settings.txt %logdir%\config.txt /b
) else (
copy %logdir%\main.txt+%logdir%\settings.txt %logdir%\config.txt /b
))

%logdir%\EthDcrMiner64.exe %logdir%\config.txt

Olie1234

newbie

Activity: 2

Merit: 0

Can some please tell me what is preventing claymore core voltage setting to change, I changed it to 975 and now its not changing anymore, in watttool is show change by not in gpu-z.
No Wattman installed and uninstalled msi afterburner. Tx.

LJLT

newbie

Activity: 48

Merit: 0

Quote from: LJLT on June 21, 2017, 11:56:37 PM

Hi guys, today i tried ver 9.5 two of my rigss all good. But the third one when i double click the .bat file it opens and close the comand line window in micro seconds.

I already deactivaded the win defender, dont know why this is happening.

Can someone help me.

Thanks

Please guys anyone, one piece of advice...

draz117

newbie

Activity: 1

Merit: 0

I downloaded the V9.5 and i keep getting this error for gtx 1060 3gb
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.

Tiuz

newbie

Activity: 1

Merit: 0

Quote from: Claymore on June 19, 2017, 10:25:44 AM

Quote from: sofianeelec on June 19, 2017, 08:33:49 AM

Quote from: davescream on June 18, 2017, 04:20:59 PM

Claymore,
do you have any ideas how to overcome Polaris hashrate drop for epoch >129 ?

Genoil said that DAG now took 100% of first memory bank (2gb) and go to second memory bank, so access two banks instead of one leads significant hashrate drop.

Do you make any research in this direction, or it is hopeless? What you think, any comments?

I have this probleme with 8g rx 480 hash drop every new dag epoche on ethereum and ethereum classic

Minergate miner say with her laste version we do not loss effective Hashrate see here;

https://minergate.com/blog/v-6-5-no-hashrate-drop-after-dag-epoch-switch/

From the description I understood that now they generate DAG on GPU too. So it is not related to this issue.

I see the speed drop. I checked possible workarounds, at least for Polaris, they failed. So probably this hashrate drop cannot be fixed, at least on miner software level.

Do you know if there are other solutions to this problem? Can this be fixed with a driver-update by AMD?

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 796. (Read 6590757 times)