I am new to mining but I started the Claymore Miner and ran it for a few hours then as i am figuring out how to add my wallet it turns out
THE DEVELOPER HAS HIS ETHEREUM WALLET ADDRESS PUT IN AS DEFAULT.
i searched his code on ethermine.org and he is getting abour an ETH a week from this. not cool.
Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 793. (Read 6590757 times)
June 24, 2017, 06:27:12 AM
June 24, 2017, 05:58:58 AM
Has anyone experienced claymore destroying your wifi connection?
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
I did find a way out of this, it looks like is some kind of interference of the GPUs working, Claymore does not have anything to do with this.
Had a free PCIe slot, have a PCIe wifi adapter, if I install it right on the slot the connection would be there but the system keep drooping shares, so I installed a raiser in order to get the wifi adapter far from the rig, now it works wonderfully
Just my 2 cents
wow, if this is the answer, I'll be so happy. I am using windows 10 and a usb wifi chip. I'll get a small hub and see if I can put the wifi card further away. Last night when I tried the usb wifi was sitting right under the GPUs. I was suspicious of interference, but didn't think too hard about it.
Now that I think about it, an USB cable extension should be enough too, gonna buy me a few of those to find out
June 24, 2017, 05:26:51 AM
Hello, I was mining with 2 GTX 1050ti for a week now.
Today I have received 4 more of these cards, but when I start the miner I get the error:
Here are the parameters
I have set the virtual memory to 16GB in Windows8.1, with 2 GPUs everything works fine. I have also used DDU to clear drivers and re-installed a fresh driver AFTER adding GPUs. Having more than 2 gives me this wierd error. Can this be corrected?
Asrock Fatal1ty H270 Performance
4GB DDR4 Ram
Intel Celeron G3920
750w Corsair MR750i 80+Gold
Asus Ex GTX 1050ti 4GB GDDR4
Thanks!
@EDIT1: Very high OC. Pulled the cards back to stock, and it's working fine. Guess I'll have to OC them again till I reach the top stable amounts
Today I have received 4 more of these cards, but when I start the miner I get the error:
Code:
GPU 0, GpuMiner cu_kd failed 4 (0), unspecified launch failure
GPU 1, GpuMiner cu_kd failed 4 (0), unspecified launch failure
GPU 1, Calc DAG failed!
GPU 0, Calc DAG failed!
GPU 2, GpuMiner cu_kd failed 4 (0), unspecified launch failure
GPU 2, Calc DAG failed!
GPU 1 failed
GPU 0 failed
GPU 2 failed
Setting DAG epoch #130 for GPU0
GPU 0, CUDA error 4 - cannot write buffer for DAG
Setting DAG epoch #130 for GPU1
GPU 1, CUDA error 4 - cannot write buffer for DAG
Setting DAG epoch #130 for GPU2
GPU 2, CUDA error 4 - cannot write buffer for DAG
ETH: 06/24/17-12:22:40 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s
GPU 0 failed
GPU 2 failed
GPU 1 failed
GPU 1, GpuMiner cu_kd failed 4 (0), unspecified launch failure
GPU 1, Calc DAG failed!
GPU 0, Calc DAG failed!
GPU 2, GpuMiner cu_kd failed 4 (0), unspecified launch failure
GPU 2, Calc DAG failed!
GPU 1 failed
GPU 0 failed
GPU 2 failed
Setting DAG epoch #130 for GPU0
GPU 0, CUDA error 4 - cannot write buffer for DAG
Setting DAG epoch #130 for GPU1
GPU 1, CUDA error 4 - cannot write buffer for DAG
Setting DAG epoch #130 for GPU2
GPU 2, CUDA error 4 - cannot write buffer for DAG
ETH: 06/24/17-12:22:40 - New job from eu2.ethermine.org:4444
ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s
GPU 0 failed
GPU 2 failed
GPU 1 failed
Here are the parameters
Code:
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu2.ethermine.org:4444 -ewal 0xc141f8A43bf450B36948eC9C3Fe5068f8deF6Ced.rig1 -epsw x
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu2.ethermine.org:4444 -ewal 0xc141f8A43bf450B36948eC9C3Fe5068f8deF6Ced.rig1 -epsw x
I have set the virtual memory to 16GB in Windows8.1, with 2 GPUs everything works fine. I have also used DDU to clear drivers and re-installed a fresh driver AFTER adding GPUs. Having more than 2 gives me this wierd error. Can this be corrected?
Asrock Fatal1ty H270 Performance
4GB DDR4 Ram
Intel Celeron G3920
750w Corsair MR750i 80+Gold
Asus Ex GTX 1050ti 4GB GDDR4
Thanks!
@EDIT1: Very high OC. Pulled the cards back to stock, and it's working fine. Guess I'll have to OC them again till I reach the top stable amounts
June 24, 2017, 04:51:23 AM
I found a few recent questions related to low speed of LBC mining in dual mode. Check Readme, "KNOWN ISSUES" section:
.....
- LBC PoW is not very good for dual mining, it causes a bit less Ethereum mining speed.
.....
Also ASM mode is not implemented for LBC yet, but I'm working on it and expect about x2 speedup for LBC when it is finished (for AMD cards). It's a lot of work though, so it will take some more time.
.....
- LBC PoW is not very good for dual mining, it causes a bit less Ethereum mining speed.
.....
Also ASM mode is not implemented for LBC yet, but I'm working on it and expect about x2 speedup for LBC when it is finished (for AMD cards). It's a lot of work though, so it will take some more time.
June 24, 2017, 04:44:05 AM
Something I really dislike about your miner Claymore is the fact that if I'm dual mining ETC, when DevFee starts I lose another 30-40 seconds because it needs to swap to a different DAG and then after DevFee ends it changes again to a different DAG (132 on ETC 130 on ETH).
I really, really dislike it about your miner.
Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.
I really, really dislike it about your miner.
Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.
+1 i'm also loosing speed because of this
+1 too.
Also if mining on NiceHash is even worse, as you can get whatever coin with daggerhashimoto algo, and swap DAG like crazy :-D
Ok in next update I will improve nicehash support (so devfee will be mined there too) and add "-allcoins etc" mode which selects devfee ETC pools. New version will be available in 2-3 days.
June 24, 2017, 03:24:59 AM
Something I really dislike about your miner Claymore is the fact that if I'm dual mining ETC, when DevFee starts I lose another 30-40 seconds because it needs to swap to a different DAG and then after DevFee ends it changes again to a different DAG (132 on ETC 130 on ETH).
I really, really dislike it about your miner.
Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.
I really, really dislike it about your miner.
Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.
+1 i'm also loosing speed because of this
+1 too.
Also if mining on NiceHash is even worse, as you can get whatever coin with daggerhashimoto algo, and swap DAG like crazy :-D
June 24, 2017, 03:07:07 AM
the miner do not restart when gpu hang, i need to reboot manualy all the rig to start miner correctly a gain !
do you have a reboot.bat/reboot.sh with shutdown called inside ?
if yes, there is a problem. often when GPU hang because of overclocking and heat, there are many memory errors in kernel logs, and the linux kernel end with a panic on unstoppable processor thread. I use a hardware watchdog
no i do not use reboot.bat i use default wd I mean just restart miner when gpu hang and this not hapened when gpu hang
any help
June 24, 2017, 01:53:12 AM
Something I really dislike about your miner Claymore is the fact that if I'm dual mining ETC, when DevFee starts I lose another 30-40 seconds because it needs to swap to a different DAG and then after DevFee ends it changes again to a different DAG (132 on ETC 130 on ETH).
I really, really dislike it about your miner.
Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.
I really, really dislike it about your miner.
Just set an ETC pool for your devfee if mining ETC for christ sake, I understand you do a good job with your miners (you also make an awful lot of money, but it's cool anyway, it's deserved), but that's a long way from 1-2%, it's much closer to around 5% of lost hashrate each our with this dag swapping.
+1 i'm also loosing speed because of this
June 24, 2017, 01:45:45 AM
Has anyone experienced claymore destroying your wifi connection?
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
I did find a way out of this, it looks like is some kind of interference of the GPUs working, Claymore does not have anything to do with this.
Had a free PCIe slot, have a PCIe wifi adapter, if I install it right on the slot the connection would be there but the system keep drooping shares, so I installed a raiser in order to get the wifi adapter far from the rig, now it works wonderfully
Just my 2 cents
wow, if this is the answer, I'll be so happy. I am using windows 10 and a usb wifi chip. I'll get a small hub and see if I can put the wifi card further away. Last night when I tried the usb wifi was sitting right under the GPUs. I was suspicious of interference, but didn't think too hard about it.
June 23, 2017, 10:54:03 PM
@Claymore,
Could you please check memory controller load? As others stated some cards randomly gets lower load on memory controller and this causes decreased hashrate.
For instance, my average hash rate should be around 264,5 MH/s for my 9 gpu rig. But it displays effective hourly rate around 205.0 MH/s.
I have tested this for more than 7 hours and this is the case for me. Even on ETH only mining using fine tuning and low power bios.
9 gpu rigCould you please check memory controller load? As others stated some cards randomly gets lower load on memory controller and this causes decreased hashrate.
For instance, my average hash rate should be around 264,5 MH/s for my 9 gpu rig. But it displays effective hourly rate around 205.0 MH/s.
I have tested this for more than 7 hours and this is the case for me. Even on ETH only mining using fine tuning and low power bios.
Is that nVidia?
June 23, 2017, 08:25:31 PM
Hi Claymore,
Is there any chance you can fix the "memory problem" that will affect Polaris Cards very soon ?
I quoted "memory problem" because it will also affect 8GB cards next month so there's not only a memory problem, but something else related to Polaris Cards
Thanks in advance for your answer
Is there any chance you can fix the "memory problem" that will affect Polaris Cards very soon ?
I quoted "memory problem" because it will also affect 8GB cards next month so there's not only a memory problem, but something else related to Polaris Cards
Thanks in advance for your answer
June 23, 2017, 08:20:44 PM
Has anyone experienced claymore destroying your wifi connection?
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
I did find a way out of this, it looks like is some kind of interference of the GPUs working, Claymore does not have anything to do with this.
Had a free PCIe slot, have a PCIe wifi adapter, if I install it right on the slot the connection would be there but the system keep drooping shares, so I installed a raiser in order to get the wifi adapter far from the rig, now it works wonderfully
Just my 2 cents
June 23, 2017, 05:51:24 PM
the miner do not restart when gpu hang, i need to reboot all the rig to start miner correctly
do you have a reboot.bat/reboot.sh with shutdown called inside ?
if yes, there is a problem. often when GPU hang because of overclocking and heat, there are many memory errors in kernel logs, and the linux kernel end with a panic on unstoppable processor thread. I use a hardware watchdog
no i do not use reboot.bat i use default wd I mean just restart miner when gpu hang and this not hapened when gpu hang
June 23, 2017, 05:48:12 PM
For Nvidia slow hashrate, install windows 10 creators update.
June 23, 2017, 04:45:30 PM
the miner do not restart when gpu hang, i need to reboot all the rig to start miner correctly
do you have a reboot.bat/reboot.sh with shutdown called inside ?
if yes, there is a problem. often when GPU hang because of overclocking and heat, there are many memory errors in kernel logs, and the linux kernel end with a panic on unstoppable processor thread. I use a hardware watchdog
June 23, 2017, 04:39:19 PM
Has anyone experienced claymore destroying your wifi connection?
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
Yes (on Ubuntu)
probably the interferences.
put the antenna further away from rig, and use a big antenna, or CPL (plugger farther)
June 23, 2017, 04:15:22 PM
hello,
i have probleme with claymore miner
the miner do not restart when gpu hang, i need to reboot all the rig to start miner correctly
the claymore miner stop mining, and the wd is activated and can i know witch gpu hang, and the miner try to restart but hang and not continue,
befor i do not have this probleme, when gpu hang the miner restart correctly and keep mining with any probleme
All your help are welcome
Thanks
i have probleme with claymore miner
the miner do not restart when gpu hang, i need to reboot all the rig to start miner correctly
the claymore miner stop mining, and the wd is activated and can i know witch gpu hang, and the miner try to restart but hang and not continue,
befor i do not have this probleme, when gpu hang the miner restart correctly and keep mining with any probleme
All your help are welcome
Thanks
any one to help this is serieus probleme !
June 23, 2017, 03:39:16 PM
Hello, i have looked at a lot of the pages in this thread but can not find my issue. I have 5 GTX 1060 msi 3gb cards, trying to use claymore miner. It starts to mine fine then crashes with the following error.
GPU 1, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 1, GpuMiner kx failed 1
GPU 3, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 1, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 2, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 1 failed
GPU 3, GpuMiner kx failed 1
GPU 1, GpuMiner kx failed 1
GPU 2, GpuMiner kx failed 1
GPU 0, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 3, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 3 failed
GPU 1 failed
GPU 2, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 2 failed
GPU 0, GpuMiner kx failed 1
GPU 3, GpuMiner kx failed 1
GPU 2, GpuMiner kx failed 1
GPU 0, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 0 failed
GPU 3 failed
GPU 2 failed
GPU 0, GpuMiner kx failed 1
GPU 0 failed
******************************************
here is my batch file.
timeout /t 10
@echo %time% %date%
@echo off
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
EthDcrMiner64.exe -tt 0 -epool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -ewal 18PPjuF7psTxFRWcP7dBZgbGRHW78fGGWB -epsw x -esm 3 -allpools 1 -estale 0 -dpool stratum+tcp://decred.eu.nicehash.com:3354 -dwal 18PPjuF7psTxFRWcP7dBZgbGRHW78fGGWB
**********************************************
also, device manager shows 5 gpus, but claymore only finds 4. Any tips on this as well.
any help would be appreciated.
I have the same issue with him! My rig have 6 VGA Giga 3gb, but 1st VGA stoped GPU 1, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 1, GpuMiner kx failed 1
GPU 3, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 1, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 2, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 1 failed
GPU 3, GpuMiner kx failed 1
GPU 1, GpuMiner kx failed 1
GPU 2, GpuMiner kx failed 1
GPU 0, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 3, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 3 failed
GPU 1 failed
GPU 2, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 2 failed
GPU 0, GpuMiner kx failed 1
GPU 3, GpuMiner kx failed 1
GPU 2, GpuMiner kx failed 1
GPU 0, GpuMiner cu_k00 failed 4, unspecified launch failure
GPU 0 failed
GPU 3 failed
GPU 2 failed
GPU 0, GpuMiner kx failed 1
GPU 0 failed
******************************************
here is my batch file.
timeout /t 10
@echo %time% %date%
@echo off
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
EthDcrMiner64.exe -tt 0 -epool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -ewal 18PPjuF7psTxFRWcP7dBZgbGRHW78fGGWB -epsw x -esm 3 -allpools 1 -estale 0 -dpool stratum+tcp://decred.eu.nicehash.com:3354 -dwal 18PPjuF7psTxFRWcP7dBZgbGRHW78fGGWB
**********************************************
also, device manager shows 5 gpus, but claymore only finds 4. Any tips on this as well.
any help would be appreciated.
Have anyone help us (If you are having a single card first (others may fail afterward but usually starts with the same card), check your riser. specifically I would replace the cheap USB cable that comes with it along with the power adapter if you are using it. That's where most of my failures have been from. The other thing to check is to put a meter at the wall and see what your total draw is and make sure you are not maxing out your power supply.
i have a 850 power supply and each card is using 105-110 watt, so i should have plenty of power. Also, the issue happens with 4 cards installed not even 5. Currently , i have three of the cards on the board and only one using the riser and still get the same message. three cards on the board alone run no problem. I am trying to get 4 stable before i work on the 5th. I do not know why the error keeps coming up. I will try to replace the usb cord and the molex to sata. I also have another riser board on the way from a different and better company(according to the reviews). Any other suggestions are appreciated.
June 23, 2017, 03:37:00 PM
I have R9 280x not overclocked. I started mining with claymore and Nicehash pool. Today most of the time I'm mining at 13mhs, but at unregulated time I see the mhs is raised to 25mhs in Nicehash pool. And the temperature of the card is raised to 80 degrees. At 13mhs the temp is 67 degrees. Why is that happen? Who control my card at how much mhs will mining?
What could be the reason?
My configuration bat file is:
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -ewal mywallet.worker1 -epsw x -r 1 -esm 3 -allpools 1 -estale 0 -dpool stratum+tcp://decred.eu.nicehash.com:3354 -dwal mywallet .worker1
What could be the reason?
My configuration bat file is:
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -ewal mywallet.worker1 -epsw x -r 1 -esm 3 -allpools 1 -estale 0 -dpool stratum+tcp://decred.eu.nicehash.com:3354 -dwal mywallet .worker1
Mine ZEC with your 280X. Don't mine ETH.
June 23, 2017, 03:32:08 PM
Has anyone experienced claymore destroying your wifi connection?
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
Without claymore running I can ping my gateway all <50ms. As soon as claymore starts mining the connection seems to be wrecked. Pings drop and claymore cannot access the network. Some pings get through but very few and with huge delays (3000 ms).
The only solution I've seen people talk about is hardwiring. I've noticed it only happens with my new router and my rig on the old router works. However I cannot reach the old router from where I want the new rig.
Jump to: