Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 823. (Read 6590718 times)
June 13, 2017, 11:57:41 AM
When I mining on Eth only mode i get 88 mh/s when I switch to Eth + Sia dual mode I get 16 mh/s . wasnt the Eth hashrate suposed to be equal in dual mining mode?
June 13, 2017, 11:51:52 AM
batch:-
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1.123 -epsw x
but i get this error? where am going wrong? must be making a simple mistake
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_FORCE_64BIT_PTR 0
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_MAX_HEAP_SIZE 100
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_USE_SYNC_OBJECTS 1
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_MAX_ALLOC_PERCENT 100
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_SINGLE_ALLOC_PERCENT 100
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D856
4f1F3E4bF73a02a2Cd1.home1 -epsw
'EthDcrMiner64.exe' is not recognized as an internal or external command,
operable program or batch file.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>pause
Press any key to continue . . .
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1.123 -epsw x
but i get this error? where am going wrong? must be making a simple mistake
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_FORCE_64BIT_PTR 0
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_MAX_HEAP_SIZE 100
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_USE_SYNC_OBJECTS 1
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_MAX_ALLOC_PERCENT 100
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>setx GPU_SINGLE_ALLOC_PERCENT 100
SUCCESS: Specified value was saved.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D856
4f1F3E4bF73a02a2Cd1.home1 -epsw
'EthDcrMiner64.exe' is not recognized as an internal or external command,
operable program or batch file.
C:\Users\GADGET-ELECTRONICS\Desktop\Claymore CryptoNote GPU Miner v9.7 Beta - PO
OL>pause
Press any key to continue . . .
June 13, 2017, 11:35:08 AM
Wolf0, I'm a little confused on the memory issue. What is the desired memory on the RX480? Are there any to totally stay away from? And how can you tell what memory a card has before you buy it. I search for specs and it's not something that really seems to be listed. Maybe I'm missing it.
4GB is more than adequate. If you have 8GB it might hash slightly faster but a lot of the extra memory is not used for mining.
Sorry. I should have been more specific. I'm talking about the brand of memory. If I'm wanting a good performing card, what is the better brand of memory to seek out. And how can you tell what it is before you buy it.
June 13, 2017, 11:28:13 AM
Quick shoutout for anyone still running v9.3 on Win10 - Defender just decided it was a Trojan and deleted it on my rigs. v9.5 appears to be fine ...
Always smart to add a Windows Defender exception on the folder you keep your mining software in. Miners regularly get falsely flagged as trojans because they get packaged in trojans.
I already do that and it is working perfectly.
June 13, 2017, 11:19:16 AM
Quick shoutout for anyone still running v9.3 on Win10 - Defender just decided it was a Trojan and deleted it on my rigs. v9.5 appears to be fine ...
Always smart to add a Windows Defender exception on the folder you keep your mining software in. Miners regularly get falsely flagged as trojans because they get packaged in trojans.
June 13, 2017, 11:07:42 AM
Hey I detached my DVI from gpu and now I attached it to the onboard.
If I launch miner drivers and miner say no gpu detected.
Windows detects it (Radeon drivers do not).
Any chance?
If I launch miner drivers and miner say no gpu detected.
Windows detects it (Radeon drivers do not).
Any chance?
June 13, 2017, 11:03:52 AM
Hi all, new to mining world.
I'm learning the basics of mining
After a little trouble, i set up a win 7 x64 rig with 1 Vaporx 7970 3G and an MSI GTX 780 3G
I'm running EthDcrMiner64.exe -epool http://localhost:8545 -asm 1 -mode 1 -tt 80 -benchmark 1
Total hashrate is 27,8 Mh/s
ATI hashrate 13 Mh/s catalist crimson 15.12
Nvidia hashrate 14,8 Mh/s driver 382.33 cuda 8
Now the questions:
1 - Ati hashrate isn't too low?
2 - Nvidia start ming at 17 Mh/s and after few seconds drops to 14~, maybe the temperature that is around 85°C?
3 - Can you suggest me some trick and options to optimize hashing rate and the cooling of the nvidia card?
Thanks in advance!
I'm learning the basics of mining
After a little trouble, i set up a win 7 x64 rig with 1 Vaporx 7970 3G and an MSI GTX 780 3G
I'm running EthDcrMiner64.exe -epool http://localhost:8545 -asm 1 -mode 1 -tt 80 -benchmark 1
Total hashrate is 27,8 Mh/s
ATI hashrate 13 Mh/s catalist crimson 15.12
Nvidia hashrate 14,8 Mh/s driver 382.33 cuda 8
Now the questions:
1 - Ati hashrate isn't too low?
2 - Nvidia start ming at 17 Mh/s and after few seconds drops to 14~, maybe the temperature that is around 85°C?
3 - Can you suggest me some trick and options to optimize hashing rate and the cooling of the nvidia card?
Thanks in advance!
June 13, 2017, 10:58:54 AM
Guys im having trouble getting the batch file correct i think, would someone be able to give me one to run ive tried all sorts but it just starts up in the black command window then goes straight off. ive tried different pools also
The weird thing is if i click on the start batch file that comes in claymoores folder it starts up fine and my cards all start hashing on there servers / accounts
im runnning 3 x r380 on win 7 64 bit
Batch files ive tried to use are:
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1.123 -epsw x
and
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1 -epsw x
and
-o stratum+tcp://us-east.cryptonight-hub.miningpoolhub.com:20580
-u andi1571.home
-p x
#-allpools 1
#-tt 75
and
NsGpuCNMiner.exe -o stratum+tcp://xmr-eu.dwarfpool.com:8050 -u 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1
The weird thing is if i click on the start batch file that comes in claymoores folder it starts up fine and my cards all start hashing on there servers / accounts
im runnning 3 x r380 on win 7 64 bit
Batch files ive tried to use are:
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1.123 -epsw x
and
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1 -epsw x
and
-o stratum+tcp://us-east.cryptonight-hub.miningpoolhub.com:20580
-u andi1571.home
-p x
#-allpools 1
#-tt 75
and
NsGpuCNMiner.exe -o stratum+tcp://xmr-eu.dwarfpool.com:8050 -u 0x9793F71eC2f913d01D8564f1F3E4bF73a02a2Cd1
June 13, 2017, 10:33:56 AM
Quick shoutout for anyone still running v9.3 on Win10 - Defender just decided it was a Trojan and deleted it on my rigs. v9.5 appears to be fine ...
Just go into Defender and tell it the offending exe, dll, etc is allowed. They came up as trojans because dumbass scumbags use the code in mining bots.
June 13, 2017, 10:32:32 AM
1060/1070 prices gone crazy in my country, LOL 
ETH skyrocket... BTC drops.. My pool went from 7 to 10 TH/s in few days..
What do you think about 570/4GB, will it still be worth it when they restock, if they...? Amazon only shows preorder on all RXses..
ETH skyrocket... BTC drops.. My pool went from 7 to 10 TH/s in few days..What do you think about 570/4GB, will it still be worth it when they restock, if they...? Amazon only shows preorder on all RXses..
570 4GB will be worth buying if you are lucky enough to find one.
June 13, 2017, 10:30:56 AM
Wolf0, I'm a little confused on the memory issue. What is the desired memory on the RX480? Are there any to totally stay away from? And how can you tell what memory a card has before you buy it. I search for specs and it's not something that really seems to be listed. Maybe I'm missing it.
4GB is more than adequate. If you have 8GB it might hash slightly faster but a lot of the extra memory is not used for mining.
June 13, 2017, 10:29:03 AM
Hi Everybody:
As a lot of messages I have seen here, I will start stating that I'm new here and new in mining, I started mining on friday, so far great, I have learnt a lot.
Right now I am mining with only 3 ASUS STRIX RX580 8GB OC, I have reduced the GPU clock in 5% and increased the memory clock speed to 2200 MHz, I have got 27.4 MH/s from 24.5MH/s, all this in AMDs Wattman, I had problems with the Asus Aura Light Effects, it seems it mess with the MH/s fluency, It is off and uninstalled now.
I have read about some widely known power adjustments, I understand the idea is to reduce voltage, so reduce power consumption, and increase memory clock speed, so increase MH/s, I have read too about doing it with AMDs Wattman or MSIs AfterBurner, and about bios flashing.
Knowing many has been able to get 29MH/s and 135 Watts of power from this cards, my questions so far are the following:
- There is need to flash a new bios to get the best performance?, if so, how many MH/s could I get?, or power reduction?.
- If I can get similar improvements with AMDs Wattman, which are the parameters I must use?.
Thank you very much for your support.
Carlos
As a lot of messages I have seen here, I will start stating that I'm new here and new in mining, I started mining on friday, so far great, I have learnt a lot.
Right now I am mining with only 3 ASUS STRIX RX580 8GB OC, I have reduced the GPU clock in 5% and increased the memory clock speed to 2200 MHz, I have got 27.4 MH/s from 24.5MH/s, all this in AMDs Wattman, I had problems with the Asus Aura Light Effects, it seems it mess with the MH/s fluency, It is off and uninstalled now.
I have read about some widely known power adjustments, I understand the idea is to reduce voltage, so reduce power consumption, and increase memory clock speed, so increase MH/s, I have read too about doing it with AMDs Wattman or MSIs AfterBurner, and about bios flashing.
Knowing many has been able to get 29MH/s and 135 Watts of power from this cards, my questions so far are the following:
- There is need to flash a new bios to get the best performance?, if so, how many MH/s could I get?, or power reduction?.
- If I can get similar improvements with AMDs Wattman, which are the parameters I must use?.
Thank you very much for your support.
Carlos
If you're still using Windows (which is about as stable as a house of cards during a hurricane), then you can easily undervolt using MSI AB or whatever. Also, only 27.4MH/s? Those can't be Samsung, are they?
LOL.... "...If you're still using Windows (which is about as stable as a house of cards during a hurricane)..." ~ Wolf0, 2017
thanks for brief grin... needed one.... after the BTC bloodbath last night
27.5mh
possibly SK-Hynix... lucky card this
Use GPUZ to find out memory type
It seems I am Lucky, these are Samsung, just checked.
What I need to change?, which settings must I use?.
Thx very much,
Damn! I thought copy+paste hackjob from 1750 -> 2000 would do better than that on Samsung K4G80325FB. I figured at least 28.5MH/s (which still, for Samsung, is not good) but... wow.
Wolf0, I'm a little confused on the memory issue. What is the desired memory on the RX480? Are there any to totally stay away from? And how can you tell what memory a card has before you buy it. I search for specs and it's not something that really seems to be listed. Maybe I'm missing it.
June 13, 2017, 10:28:39 AM
Quick shoutout for anyone still running v9.3 on Win10 - Defender just decided it was a Trojan and deleted it on my rigs. v9.5 appears to be fine ...
June 13, 2017, 10:18:12 AM
Claymore,
the problem with ETHMan 3.1 + Dualminer 9.5
If some rig go down, and then after some time goes up, it dosent restore in ETHMan, on screenshot you see that miner restarted and work, i launched web console and it works already 2 minutes, but ETHMan still show "lost ****". Even after 10 minutes ETHMan dosent see rig. So as it was with ETHMan 3.0, I need restart it to see all rigs stats again.
If you included cryptography and https, then maybe here some trouble with ssl? need to update certificate if connection was lost?
Can confirm this, same problem here.
The last update of EthMan improved the 100% lock after a warning, but a rig which was offline and comes back up is not (always?) shown as alive until EthMan is restarted.
Also the batch action is still not retriggered in case of a persisting failure.
the problem with ETHMan 3.1 + Dualminer 9.5
If some rig go down, and then after some time goes up, it dosent restore in ETHMan, on screenshot you see that miner restarted and work, i launched web console and it works already 2 minutes, but ETHMan still show "lost ****". Even after 10 minutes ETHMan dosent see rig. So as it was with ETHMan 3.0, I need restart it to see all rigs stats again.
If you included cryptography and https, then maybe here some trouble with ssl? need to update certificate if connection was lost?
Can confirm this, same problem here.
The last update of EthMan improved the 100% lock after a warning, but a rig which was offline and comes back up is not (always?) shown as alive until EthMan is restarted.
Also the batch action is still not retriggered in case of a persisting failure.
I spent half a day in attempts to reproduce it, but it works fine for me, weird. If you can 100% reproduce this issue I can prepare debug version with logging and send it to you so I can get more info. PM me if you want to participate.
Retriggering: if a rig was lost, BAT file will be executed. If rig is back again and then again will be lost, BAT will be executed again. What's wrong exactly?
I can not 100% reproduce it. Just had the error again two hours ago. Rig already back online but shown as offline for 2+ hours. But it does not happen always, some additional aspect I don't see at the moment must play a role here. But of course I can try to help if you have a logging debug version for me.
Retriggering: as I already wrote - a single action may not be sufficient to bringt the rig back up. (i.e.: rig hangs - action triggered -> auto-reset rig - if windows boots into recovery mode because it is the x-th reset in a row you are ...... - the rig stays offline waiting for user input until infinity).
So: if an action did not bring the rig back up after the same delay time, it should trigger the same action again and again until the problem is resolved. (Leaving out luxury options like number of max. attempts or configurable follow up delay
) June 13, 2017, 10:13:02 AM
2% ? wasn't the fee 1% ?
I know zcash miner had 2%, but not eth...
Its a good miner. Just there are variables around it that show how green this area is. For instance, In windows 10 with 17.4.4 + rx570, once you start the miner I can no longer modify voltages/speeds on the fly with third party software. As soon as you close the miner, it works again.
Theres also the ordering of gpus. I still dont know how claymore miner determines which gpu is 0 and so on...
I know zcash miner had 2%, but not eth...
Its a good miner. Just there are variables around it that show how green this area is. For instance, In windows 10 with 17.4.4 + rx570, once you start the miner I can no longer modify voltages/speeds on the fly with third party software. As soon as you close the miner, it works again.
Theres also the ordering of gpus. I still dont know how claymore miner determines which gpu is 0 and so on...
June 13, 2017, 10:12:03 AM
How do you check for memory errors under Linux? I was asking this question few times with no answer 
Quite serious ones will appear in the kernel log - so you'd just check dmesg. I'm pretty sure there's a register with the count somewhere in the space, if I directly access the GPU (not bothering with the driver), but there's already SO MUCH awesome shit I can do with this access that I have yet to implement (and I've implemented plenty!) so it's not that high on my TODO list...When Claymore launch watchdog because of hang, I always spot erreors in the kernel logs (journal -k | grep amdgpu ). It is mostly segmentation faults...
I don't know how you can detect memory errors... it it hardware ECC silent errors counted ? parity errors?
normally uncorrected errors cause bad computation, thus incorrect shares. My rule is that when my watchdog detect incorrect share of GPU hanging, the bios is blacklisted and another selected. Bios don't make two errors, they are fired at the first
.I've got one gpu, which make one incorrect share for 2-3 thousands good shares, running 30.7 Mhs. Zero memory errors on hwinfo64. And you would trash its bios? Can't agree..
June 13, 2017, 09:58:40 AM
How do you check for memory errors under Linux? I was asking this question few times with no answer
Quite serious ones will appear in the kernel log - so you'd just check dmesg. I'm pretty sure there's a register with the count somewhere in the space, if I directly access the GPU (not bothering with the driver), but there's already SO MUCH awesome shit I can do with this access that I have yet to implement (and I've implemented plenty!) so it's not that high on my TODO list...When Claymore launch watchdog because of hang, I always spot erreors in the kernel logs (journal -k | grep amdgpu ). It is mostly segmentation faults...
I don't know how you can detect memory errors... it it hardware ECC silent errors counted ? parity errors?
normally uncorrected errors cause bad computation, thus incorrect shares. My rule is that when my watchdog detect incorrect share of GPU hanging, the bios is blacklisted and another selected. Bios don't make two errors, they are fired at the first
. 
June 13, 2017, 09:57:18 AM
I don't use crossfire, GPUZ show crossfire is disable.
I d'ont know what is RDP
I d'ont know what is RDP
i think the main reason you put the card to the pci-e directly
June 13, 2017, 09:52:38 AM
I don't use crossfire, GPUZ show crossfire is disable.
I d'ont know what is RDP
Edit : After research, RDP is Remote Desktop Connection.
ok !
I test with team viewer et OMG this problème is resolved!
Thank you
I d'ont know what is RDP
Edit : After research, RDP is Remote Desktop Connection.
ok !
I test with team viewer et OMG this problème is resolved!
Thank you
June 13, 2017, 09:45:11 AM
Hello everyone.
I’m a new guy in this forum and i come to expose my big problème with claymore.
I don’t find solution and nobody knows how to help me.
I mine with 6 RX 480 4Go Nitro Sapphire on windows 10.
As you cas see on this picture, i have good result BUT, about FAN, i can’t see all of GPU.
I always see the GPU0 FAN.
I don’t know why, but before i always see all of GPU FANS.
And i use MISafterburer to OC my cards but claymore just OC the GPU0 and not all cards.
I think it's probably because i just see gpu0 fans.
Have you an explication about my problème ?
I test claymore 9,4, and 9,5 but this problème existe on all claymore version.
Thank you.
I’m a new guy in this forum and i come to expose my big problème with claymore.
I don’t find solution and nobody knows how to help me.
I mine with 6 RX 480 4Go Nitro Sapphire on windows 10.
As you cas see on this picture, i have good result BUT, about FAN, i can’t see all of GPU.
I always see the GPU0 FAN.
I don’t know why, but before i always see all of GPU FANS.
And i use MISafterburer to OC my cards but claymore just OC the GPU0 and not all cards.
I think it's probably because i just see gpu0 fans.
Have you an explication about my problème ?
I test claymore 9,4, and 9,5 but this problème existe on all claymore version.
Thank you.
Uff still the same question for milionth time. Disable crossfire, don't use RDP...
Jump to: