Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 172.

AriesIV10

legendary

Activity: 1260

Merit: 1006

Mine for a Bit

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Maybe today we will see and update.

GH

member

Activity: 117

Merit: 10

Quote from: adaseb on February 10, 2017, 09:16:29 AM

Guess the coin (against the USD)

Fits 99% of all altcoins Roll Eyes

(OT)

adaseb

legendary

Activity: 3808

Merit: 1723

Guess the coin (against the USD)

haxiboy

newbie

Activity: 36

Merit: 0

Quote from: br2459 on February 10, 2017, 08:45:38 AM

Quote from: GH on February 10, 2017, 05:39:40 AM

Quote from: enricosofie on February 10, 2017, 05:10:44 AM

Hi,

I have 2 GPU's (rx480) in a system.
Yesterday it just rebooted and since then I get only the GPU temperature en fanspeed of GPU0.
I do not get to see the temperature and fanspeed of GPU1

What's wrong with this setup?
How to fix it?

regards,
Eric

Sounds like CrossFire is accidentally enabled. I would check.

Second that ^. I had that problem every time I installed new drivers for my 480s it would want to put them in cross-fire.

Disable crossfire and you may want to use hdmi dummy plugs

br2459

full member

Activity: 269

Merit: 102

Quote from: GH on February 10, 2017, 05:39:40 AM

Quote from: enricosofie on February 10, 2017, 05:10:44 AM

Hi,

I have 2 GPU's (rx480) in a system.
Yesterday it just rebooted and since then I get only the GPU temperature en fanspeed of GPU0.
I do not get to see the temperature and fanspeed of GPU1

What's wrong with this setup?
How to fix it?

regards,
Eric

Sounds like CrossFire is accidentally enabled. I would check.

Second that ^. I had that problem every time I installed new drivers for my 480s it would want to put them in cross-fire.

ujang1

hero member

Activity: 558

Merit: 500

Quote from: enricosofie on February 10, 2017, 05:10:44 AM

Hi,

I have 2 GPU's (rx480) in a system.
Yesterday it just rebooted and since then I get only the GPU temperature en fanspeed of GPU0.
I do not get to see the temperature and fanspeed of GPU1

What's wrong with this setup?
How to fix it?

regards,
Eric

Install MSI Afterburner and see there the temperature and fan speed. Perhaps some problems with drivers and you will need to reinstall them.

GH

member

Activity: 117

Merit: 10

Quote from: enricosofie on February 10, 2017, 05:10:44 AM

Hi,

I have 2 GPU's (rx480) in a system.
Yesterday it just rebooted and since then I get only the GPU temperature en fanspeed of GPU0.
I do not get to see the temperature and fanspeed of GPU1

What's wrong with this setup?
How to fix it?

regards,
Eric

Sounds like CrossFire is accidentally enabled. I would check.

enricosofie

newbie

Activity: 47

Merit: 0

Hi,

I have 2 GPU's (rx480) in a system.
Yesterday it just rebooted and since then I get only the GPU temperature en fanspeed of GPU0.
I do not get to see the temperature and fanspeed of GPU1

What's wrong with this setup?
How to fix it?

regards,
Eric

Zealotki11er

newbie

Activity: 19

Merit: 0

Quote from: IOTUSA on February 09, 2017, 10:51:58 AM

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Have you tested any new drivers? Would be nice to be able to just run the 17.x drivers across all cards to uniform rigs. Perhaps someone else here has some info statistics for 200/300/400 series cards using latest AMD Drivers? (this 15.12, 16.3 etc. driver mixing is driving me bonkers!)

I am using 17.1.2 with 290X and performance is the same as 16.11.3 and 16.8.2.

KrokoTill

newbie

Activity: 51

Merit: 0

Quote from: Bojcha on February 09, 2017, 04:16:30 PM

Quote from: KrokoTill on February 09, 2017, 04:05:51 PM

Quote from: Bojcha on February 09, 2017, 02:39:16 PM

Quote from: ?? on ??

Quote from: IOTUSA on February 09, 2017, 10:51:58 AM

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Have you tested any new drivers? Would be nice to be able to just run the 17.x drivers across all cards to uniform rigs. Perhaps someone else here has some info statistics for 200/300/400 series cards using latest AMD Drivers? (this 15.12, 16.3 etc. driver mixing is driving me bonkers!)

If we did that though I don't think we would be able to mod the bios because AMD disabled bios editing in 16.12.1
Correct me if i'm wrong though.

You can always put 2 DLL's in miner folder.

It may not always help. Haven't tried with CM this trick, but opti failed to detect OpenCL devices with 15.12 dll-s while installed driver was 17.x

Depend, ofc you cannot put 15.12 if you are on RX.

It was 370, not RX. Works fine with installed 15.12, but not with dll trick.

Bojcha

hero member

Activity: 848

Merit: 500

Quote from: KrokoTill on February 09, 2017, 04:05:51 PM

Quote from: Bojcha on February 09, 2017, 02:39:16 PM

Quote from: ?? on ??

Quote from: IOTUSA on February 09, 2017, 10:51:58 AM

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Have you tested any new drivers? Would be nice to be able to just run the 17.x drivers across all cards to uniform rigs. Perhaps someone else here has some info statistics for 200/300/400 series cards using latest AMD Drivers? (this 15.12, 16.3 etc. driver mixing is driving me bonkers!)

If we did that though I don't think we would be able to mod the bios because AMD disabled bios editing in 16.12.1
Correct me if i'm wrong though.

You can always put 2 DLL's in miner folder.

It may not always help. Haven't tried with CM this trick, but opti failed to detect OpenCL devices with 15.12 dll-s while installed driver was 17.x

Depend, ofc you cannot put 15.12 if you are on RX.

KrokoTill

newbie

Activity: 51

Merit: 0

Quote from: Bojcha on February 09, 2017, 02:39:16 PM

Quote from: ?? on ??

Quote from: IOTUSA on February 09, 2017, 10:51:58 AM

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Have you tested any new drivers? Would be nice to be able to just run the 17.x drivers across all cards to uniform rigs. Perhaps someone else here has some info statistics for 200/300/400 series cards using latest AMD Drivers? (this 15.12, 16.3 etc. driver mixing is driving me bonkers!)

If we did that though I don't think we would be able to mod the bios because AMD disabled bios editing in 16.12.1
Correct me if i'm wrong though.

You can always put 2 DLL's in miner folder.

It may not always help. Haven't tried with CM this trick, but opti failed to detect OpenCL devices with 15.12 dll-s while installed driver was 17.x

Bojcha

hero member

Activity: 848

Merit: 500

Quote from: ?? on ??

Quote from: IOTUSA on February 09, 2017, 10:51:58 AM

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Have you tested any new drivers? Would be nice to be able to just run the 17.x drivers across all cards to uniform rigs. Perhaps someone else here has some info statistics for 200/300/400 series cards using latest AMD Drivers? (this 15.12, 16.3 etc. driver mixing is driving me bonkers!)

If we did that though I don't think we would be able to mod the bios because AMD disabled bios editing in 16.12.1
Correct me if i'm wrong though.

You can always put 2 DLL's in miner folder.

IOTUSA

sr. member

Activity: 504

Merit: 250

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Have you tested any new drivers? Would be nice to be able to just run the 17.x drivers across all cards to uniform rigs. Perhaps someone else here has some info statistics for 200/300/400 series cards using latest AMD Drivers? (this 15.12, 16.3 etc. driver mixing is driving me bonkers!)

Etherion

sr. member

Activity: 512

Merit: 260

take your time and release a good one. using Op1.6.1 now so happy for now but will switch when C12 ois out

marvykkio

hero member

Activity: 798

Merit: 1000

it would be appropriate to speed up the RX 400 range, try to bring over 300

Grin

fr4nkthetank

legendary

Activity: 2294

Merit: 1182

Now the money is free, and so the people will be

Quote from: fenomenhaa on February 09, 2017, 08:43:30 AM

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

What's the expected hashrate of hawaii?i wonder how much increase .

Well on Optiminer I get almost 400, although they are overclocked a bit. I hope claymore can top that

fenomenhaa

sr. member

Activity: 248

Merit: 250

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

What's the expected hashrate of hawaii?i wonder how much increase .

fr4nkthetank

legendary

Activity: 2294

Merit: 1182

Now the money is free, and so the people will be

Quote from: Claymore on February 09, 2017, 06:21:45 AM

Damn it, I find new assembler tricks every day. I want to use them all, this causes new delays again and again. All these things take too much time.
Right now I can release an update with speedup for Hawaii cards but I had no time to add new tricks to other cards, I need a couple days for that. So no update today Sad

Claymore, the magician

We shall wait patiently. Are the speedups better than Optiminer so far ?

Redcard

newbie

Activity: 28

Merit: 0

Better release it when the zec price start to go up

Topic: Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 172. (Read 3839398 times)