Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 218.

cracker666

member

Activity: 79

Merit: 10

Quote from: Zied RF on January 16, 2017, 08:45:55 AM

Quote from: rpg on January 16, 2017, 08:32:32 AM

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

yes it's too low compared to other cards Undecided

, maybe today we will get more speed because claymore said that will get more for tonga in the next update

i get 180 with claymore and 200 with optiminer im hoping claymore beats optiminer as i prefer claymore

Astennu

newbie

Activity: 13

Merit: 0

Quote from: rpg on January 16, 2017, 08:49:41 AM

Quote from: Astennu on January 16, 2017, 08:42:06 AM

Quote from: rpg on January 16, 2017, 08:32:32 AM

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

No its not. Its a 380 not a 390.
380 = R9 285
Its similar to the R9 280 and 7950 but The 285 and 380 are GCN1.2 vs GCN1.0 and it has a 256 Bit memory bus vs 384 Bit. Shader wise it has the same 1792 shaders but a newer architecture. Fiji (Fury Cards) use the same 1.2 architecture.

R7 260 Bonaire and R9 290/390 Hawaii use GCN 1.1.

Memory speed and timings seem to impact performance quite a bit. I had a 7970 with Hynix MFR memory. it did +- 200 with timing mod it went up to 235 sol/s stock memory clocks core 1100. Memory OC on stock timings got it up to 210.

im getting ~260 on a msi 7950 that takes oc to the max thats why i'm so surprised

There are 2 reasons:
1: More memory bandwith and maybe lower latency (timing mod for the 7970 helps if you have Elpida en MFR memory AFR has quite good default timings). Also see RX480 cards that clock high compared to Tahiti and only get 250-270 ish. (there are people that report a bit higher sol/s with timing mod but then you cannot use the latest drivers)
2: ASM support only added for Tahiti and Fiji so far. That boosts performance quite a bit.

The next version of Claymore's miner might have a ASM option for Tonga based cards. Hopefully he can also add it for Polaris.
2:

rpg

hero member

Activity: 728

Merit: 500

Quote from: Astennu on January 16, 2017, 08:42:06 AM

Quote from: rpg on January 16, 2017, 08:32:32 AM

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

No its not. Its a 380 not a 390.
380 = R9 285
Its similar to the R9 280 and 7950 but The 285 and 380 are GCN1.2 vs GCN1.0 and it has a 256 Bit memory bus vs 384 Bit. Shader wise it has the same 1792 shaders but a newer architecture. Fiji (Fury Cards) use the same 1.2 architecture.

R7 260 Bonaire and R9 290/390 Hawaii use GCN 1.1.

Memory speed and timings seem to impact performance quite a bit. I had a 7970 with Hynix MFR memory. it did +- 200 with timing mod it went up to 235 sol/s stock memory clocks core 1100. Memory OC on stock timings got it up to 210.

im getting ~260 on a msi 7950 that takes oc to the max thats why i'm so surprised

Zied RF

newbie

Activity: 29

Merit: 0

Quote from: rpg on January 16, 2017, 08:32:32 AM

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

yes it's too low compared to other cards Undecided

, maybe today we will get more speed because claymore said that will get more for tonga in the next update

Astennu

newbie

Activity: 13

Merit: 0

Quote from: rpg on January 16, 2017, 08:32:32 AM

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

No its not. Its a 380 not a 390.
380 = R9 285
Its similar to the R9 280 and 7950 but The 285 and 380 are GCN1.2 vs GCN1.0 and it has a 256 Bit memory bus vs 384 Bit. Shader wise it has the same 1792 shaders but a newer architecture. Fiji (Fury Cards) use the same 1.2 architecture.

R7 260 Bonaire and R9 290/390 Hawaii use GCN 1.1.

Memory speed and timings seem to impact performance quite a bit. I had a 7970 with Hynix MFR memory. it did +- 200 with timing mod it went up to 235 sol/s stock memory clocks core 1100. Memory OC on stock timings got it up to 210. (claymore V10).
They are now doing +- 255 on 1000-1375 MHz with V11.

SpaceBallsOne

newbie

Activity: 16

Merit: 0

Quote from: rpg on January 16, 2017, 08:32:32 AM

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

i have 6 r9 380s. they get 166 -- the 380x are same speed as 380. (stock clocks, settings on v11)

rpg

hero member

Activity: 728

Merit: 500

Quote from: Zied RF on January 16, 2017, 07:43:43 AM

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

that sounds way too low. perhaps 275?

roony

full member

Activity: 196

Merit: 100

Did you see the roonies on him???

Soo, new version will be released today. Very excited

rpg

hero member

Activity: 728

Merit: 500

Quote from: CODISMYLIFE on January 16, 2017, 02:40:51 AM

guys i have question
can you tell me about hasrate of amd 7770 on new version of claymore?

about 75

Astennu

newbie

Activity: 13

Merit: 0

Quote from: imunisasi on January 16, 2017, 07:24:04 AM

Quote from: Lucky - Luciano on January 15, 2017, 04:49:45 PM

Quote from: Ursul0 on January 15, 2017, 04:17:04 PM

Quote from: Golku on January 15, 2017, 04:07:50 PM

It's not needed he uses Watttool

GPU 1180
Memory 1750
both running at 904MV

true that. I never go above 1180MHz for the core on the last phase and it's never over 925mv.
btw memory read intensive dagger-hashimoto doing fine on 850mv (total power from these 6 is below 920W in dual mining)

eth only is 816W:
https://s27.postimg.org/r55u2mro3/eth_only_zp2_816_W.png

Excellent settings. Thank you, boys. I am now graphics cards cloks 1180 GPU, 2100 GDDR5 RAM, - 48 mV, power limit +0. I now have 6 x 250 Sol / s = 1500 Sol / s and the power consumption is 880 W (measured by energy meter).

Quote from: abz1 on January 15, 2017, 05:42:55 PM

Zcash v 11 is doing quite good.

Undervolted 4 x cards I get 1046 H/s and 360 watts at the wall.

what software both of u use for that ?

Maybe MSI Afterburner.
You can also edit voltages in the drivers with AMD Wattman. I use the latter. You can set voltages and clockspeeds for multiple steps. not that interesting for mining but it is for gaming. But could also be usefull if you switch to a algo with higher load and temps. If you set a power limit it can switch to a lower speed step with lower clocks and voltages to save power. A custom bios would be nicer. But then you cant use the latest drivers.

With MSI afterburner you do have to option to change the values at the same time for similar cards. But the weakest card will be your limit then. Other cards might be able to run the same speeds at lower voltages or higher clocks at the same voltage.

Zied RF

newbie

Activity: 29

Merit: 0

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

you can get max 175 Sol/s on v11

Astennu

newbie

Activity: 13

Merit: 0

Quote from: CODISMYLIFE on January 16, 2017, 07:24:58 AM

guys can you tell me about hashrate of r9 380?

I have seen multiple listings in this topic. So search a little.
Google can also help.

If i remember correctly it was +- 160-170 ish.

CODISMYLIFE

newbie

Activity: 27

Merit: 0

guys can you tell me about hashrate of r9 380?

imunisasi

member

Activity: 86

Merit: 10

Quote from: Lucky - Luciano on January 15, 2017, 04:49:45 PM

Quote from: Ursul0 on January 15, 2017, 04:17:04 PM

Quote from: Golku on January 15, 2017, 04:07:50 PM

It's not needed he uses Watttool

GPU 1180
Memory 1750
both running at 904MV

true that. I never go above 1180MHz for the core on the last phase and it's never over 925mv.
btw memory read intensive dagger-hashimoto doing fine on 850mv (total power from these 6 is below 920W in dual mining)

eth only is 816W:

Excellent settings. Thank you, boys. I am now graphics cards cloks 1180 GPU, 2100 GDDR5 RAM, - 48 mV, power limit +0. I now have 6 x 250 Sol / s = 1500 Sol / s and the power consumption is 880 W (measured by energy meter).

Quote from: abz1 on January 15, 2017, 05:42:55 PM

Zcash v 11 is doing quite good.

Undervolted 4 x cards I get 1046 H/s and 360 watts at the wall.

what software both of u use for that ?

marvykkio

hero member

Activity: 798

Merit: 1000

guys i have a question,
As h / s to 470 8 gb
As h / s the 470 4 gb

Astennu

newbie

Activity: 13

Merit: 0

Quote from: Claymore on January 15, 2017, 10:07:42 AM

Quote from: KL0nLutiy on January 15, 2017, 09:43:18 AM

Will the new update of the miner be today?

No. I plan to release it tomorrow, need to check different drivers to improve compatibility.

Nice! Maybe this solves my problem with the Fury Nano and Nitro that i have. They cannot run ASM they go to 0 sol/s. So i force them to run normally.
Tried lower clocks and drifferent drivers but so far it was not working.

7970's are doing very well with V11.

I also had a problem with a R9 295X2 would crash after 1-2 shares. Did run stable with old 15.12 drivers but wont work with newer 16.12.2
Thats to bad because with wattman support in new drivers you can tweak the card way better. Fingers crossed for the next version

dinc

sr. member

Activity: 854

Merit: 305

Quote from: Disallowedword on January 15, 2017, 06:08:33 PM

Quote from: dinc on January 15, 2017, 04:20:54 PM

Quote from: capler on January 15, 2017, 03:52:17 PM

Quote from: Claymore on January 15, 2017, 10:07:42 AM

Quote from: KL0nLutiy on January 15, 2017, 09:43:18 AM

Will the new update of the miner be today?

No. I plan to release it tomorrow, need to check different drivers to improve compatibility.

And Linux version tomorrow?

Quote from: Claymore on January 11, 2017, 05:37:37 PM

v11.0:
..........
Linux version will be available later.

How much to wait? A year, two?

AS i think it's more difficult to make the linux version, but i notice that on linux my card has lower temp lower fan's %)

You got me wondering, how does the Watt/Sol compare between linux and windows. Normally cooler=less wattage, is this true with Claymore's Linux versions?

I have done nothing to conserve power. It seems like the top end of the hashrate is no more expensive than the lower end on the rx480 8gb. I can see it with a 10-15.00 coin like Eth, but wont there be some powermizers contemplating suicide when zec pumps to 100.00+ in a few months?

I don't sell any zec that was valued under 45.00 when the block paid. Could be me getting screwed in a few months, but seems like I have better than 50/50 chance at good profits, if/no hackers...

I said u what i see.
When I running claymore miner on linux - i have something like '60t and 71-72% fans'
Then I install Ubuntu and now i have something like '58t and 60% fans'

dragonchopper9

sr. member

Activity: 361

Merit: 250

Quote from: CODISMYLIFE on January 16, 2017, 02:40:51 AM

guys i have question
can you tell me about hasrate of amd 7770 on new version of claymore?

I do not think that such cards can mine in plus. Electricity will kill all profit. But I could be wrong.

CODISMYLIFE

newbie

Activity: 27

Merit: 0

guys i have question
can you tell me about hasrate of amd 7770 on new version of claymore?

yun9999

sr. member

Activity: 414

Merit: 251

@CLAYMORE - Which -a number is for what type of card? So far it seems the code is good at picking auto for 470 and 480 but with Fury cards, using -a 2 is best. However is auto accurate or is there better -a # for 390, 470 and 480?

Topic: Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 218. (Read 3839201 times)