Has anyone figured out how to get Dollemizer off the S9 ?
Answered my own question.
Move first jumper in upper left corner of the board, to pins 1-2 closest to the edge of the board.
Boot up from SD card with OS of your choice (BrainsOS in my case)
Topic: Dollemizer Firmware ASICBOOST Comming! [custom s9, s9i, t9 Firmware upgrade] (Read 33192 times)
November 28, 2023, 01:49:40 PM
June 07, 2020, 04:12:31 AM
Noted.
June 06, 2020, 04:41:25 PM
S9K and S9SE support for this firmware?
Some of us here take the time and effort to warn others about a scammy firmware/person and you just ignore all of that, and then a few weeks later you will come back to complain about it and look for solutions, don't be lazy, read the comments!! this firmware is SCAM, I have even left them negative feedback fairly visible on their profile.
STAY AWAY FROM THEM!!
June 06, 2020, 09:51:57 AM
S9K and S9SE support for this firmware?
January 19, 2019, 08:20:08 AM
The problem is your way of testing:
PCB temp is up to the ambient conditions of a miner.
The original FW is running roughly 620-650MHz and the energy consumption is ever rising exponentially when rising the clock speed, also the temperatures are rising (more energy = higher temperatures).
Fan set and all other settings are up to some temp measurements while single board test and boot procedure.
Further mV settings are according experiences regarding optimum IC temps for best value of has hash rate and efficiency.
Nevertheless there is a much better FW available and a better cooling system.
PCB temp is up to the ambient conditions of a miner.
The original FW is running roughly 620-650MHz and the energy consumption is ever rising exponentially when rising the clock speed, also the temperatures are rising (more energy = higher temperatures).
Fan set and all other settings are up to some temp measurements while single board test and boot procedure.
Further mV settings are according experiences regarding optimum IC temps for best value of has hash rate and efficiency.
Nevertheless there is a much better FW available and a better cooling system.
January 19, 2019, 07:45:58 AM
not....
Its just a lie.. Dev fee is a lot higher..
Its just a lie.. Dev fee is a lot higher..
indeed , it's a lie just had to try out myself
January 19, 2019, 07:37:09 AM
Hi.
I set clock to 700 and volt to 840 mv and it work good .
But FAN PWM set to 0 after 10 min and temp go to 70 .
In original firmware it never set to 0 and temp up to 60
I have an extra cooling system for a miner
Dollemizer
Org firmware
Same time in day different org and Dollemizer :/
I set clock to 700 and volt to 840 mv and it work good .
But FAN PWM set to 0 after 10 min and temp go to 70 .
In original firmware it never set to 0 and temp up to 60
I have an extra cooling system for a miner
Dollemizer
Code:
set FAN speed according to: temp_highest=70 temp_top1[PWM_T]=70 temp_top1[TEMP_POS_LOCAL]=62 temp_change=0 fix_fan_steps=-29
FAN PWM: 0
read_temp_func Done!
CRC error counter=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=0
Org firmware
Code:
Max pcb temp : 48
set FAN speed according to: temp_highest=48 temp_top1[PWM_T]=48 temp_top1[TEMP_POS_LOCAL]=48 temp_change=1 fix_fan_steps=0
FAN PWM: 30
read_temp_func Done!
CRC error counter=0
set FAN speed according to: temp_highest=48 temp_top1[PWM_T]=48 temp_top1[TEMP_POS_LOCAL]=48 temp_change=1 fix_fan_steps=0
FAN PWM: 30
read_temp_func Done!
CRC error counter=0
Same time in day different org and Dollemizer :/
November 07, 2018, 01:08:13 PM
i noticed my S9 mines to your pool for much more than 4 mins. actually for 7 minutes. ! so how do you justify this?
not....
Its just a lie.. Dev fee is a lot higher..
November 06, 2018, 11:11:05 PM
the Miner will mine in the first 4 Minutes for our fee. Then it will mine for 200 Minutes on your pools and will continue from there.
This is equivalent of ~ 1.96 % of the Mining time. (4/204)
This is equivalent of ~ 1.96 % of the Mining time. (4/204)
i noticed my S9 mines to your pool for much more than 4 mins. actually for 7 minutes. ! so how do you justify this?
October 09, 2018, 03:49:13 PM
I am not starting to test this Dollemizer Firmware against bitmain's . setting the frequency, same pool , same room , just about same everything on each miner.
i will put them on a test for 3 days and then compare the results of both " average temps " as well as " hash rate reported by the pool".
now unless the Dollemizer Firmware gives a better "something" then I do not see a need for someone to pay fees just for a better looking firmware.
i will report back once my results are final.
i will put them on a test for 3 days and then compare the results of both " average temps " as well as " hash rate reported by the pool".
now unless the Dollemizer Firmware gives a better "something" then I do not see a need for someone to pay fees just for a better looking firmware.
i will report back once my results are final.
so been testing a lil more than 3 days
. so far as for temps i see no difference, but reported hash rate is slightly better on "Dollemizer" , the pool shows around " 0.72 TH" more per miner. October 04, 2018, 04:43:10 AM
If you bothered to read the thread it has bricked a lot more than one T9+
October 03, 2018, 02:52:10 AM
How is it possible to read this thread and still ask a question like this?
The answer is nobody should ever use this firmware. Its trash and bricks machines, has hidden fees, and who knows what else. There are much better options out there.
The answer is nobody should ever use this firmware. Its trash and bricks machines, has hidden fees, and who knows what else. There are much better options out there.
well, maybe due the fact that this fw indeed has bricked one t9, but there are also t9's ocd as well,and it is still stated in the first post???
October 02, 2018, 04:03:09 PM
does this work with T9+ as well? (10.5TH)
How is it possible to read this thread and still ask a question like this?
The answer is nobody should ever use this firmware. Its trash and bricks machines, has hidden fees, and who knows what else. There are much better options out there.
October 02, 2018, 10:34:29 AM
does this work with T9+ as well? (10.5TH)
October 01, 2018, 04:04:46 AM
That has a 7% dev fee...
How do we detect if there's a Dev fee or not?
September 28, 2018, 04:59:20 PM
I am not starting to test this Dollemizer Firmware against bitmain's . setting the frequency, same pool , same room , just about same everything on each miner.
i will put them on a test for 3 days and then compare the results of both " average temps " as well as " hash rate reported by the pool".
now unless the Dollemizer Firmware gives a better "something" then I do not see a need for someone to pay fees just for a better looking firmware.
i will report back once my results are final.
i will put them on a test for 3 days and then compare the results of both " average temps " as well as " hash rate reported by the pool".
now unless the Dollemizer Firmware gives a better "something" then I do not see a need for someone to pay fees just for a better looking firmware.
i will report back once my results are final.
September 26, 2018, 10:51:43 AM
not sure if it's 7%....
can't find any info, thread or website for this...
can't find any info, thread or website for this...
It has been discussed in this forum many times just not this thread. The dev didn't put that as a disclaimer on purpose.
September 26, 2018, 09:25:42 AM
not sure if it's 7%....
can't find any info, thread or website for this...
can't find any info, thread or website for this...
September 25, 2018, 09:20:21 PM
This is another custom firmware allows to change frequency for each chip.
https://www.picclickimg.com/00/s/MTE0NlgxNjAw/z/BaQAAOSwQ2JbahZ3/$/Antminer-S9-Custom-Firmware-_57.jpg
https://www.picclickimg.com/00/s/MTE0NlgxNjAw/z/BaQAAOSwQ2JbahZ3/$/Antminer-S9-Custom-Firmware-_57.jpg
That has a 7% dev fee...
September 25, 2018, 07:43:47 PM
This is another custom firmware allows to change frequency for each chip.
https://www.picclickimg.com/00/s/MTE0NlgxNjAw/z/BaQAAOSwQ2JbahZ3/$/Antminer-S9-Custom-Firmware-_57.jpg
https://www.picclickimg.com/00/s/MTE0NlgxNjAw/z/BaQAAOSwQ2JbahZ3/$/Antminer-S9-Custom-Firmware-_57.jpg
Jump to: