[GROUP BUY 7 OPEN] Antminer 180GH @ 1.90 BTC - Chinese End of the Year Sale - - page 3.

PaintShopPro6

full member

Activity: 150

Merit: 100

Quote from: forexmasterja on January 31, 2014, 09:55:53 PM

I have to say thanks and as we say in Jamaica Nuff Respec Mon!

I ordered 3 units from Sushi for delivery to me here in Jamaica. And they were shipped and delivered exactly on time as they say they would I had the miners in hand 4 days after sending my coins.

Units that came appeared to be new and unused, even though 2 had the thermal paste leaking problem which is the least, as they all were up and hashing within 5 mins of me plugging them in.

I will definately be buying more of these units.

Big up Mon.

Thermal paste leaking out is a sure sign of new and unused

I spend 15 to 30 minutes cleaning each of my units as they come in.

They also leak some kind of clear oil that is hard to see that I clean up as well (it's from the thermal paste)

forexmasterja

full member

Activity: 130

Merit: 100

I have to say thanks and as we say in Jamaica Nuff Respec Mon!

I ordered 3 units from Sushi for delivery to me here in Jamaica. And they were shipped and delivered exactly on time as they say they would I had the miners in hand 4 days after sending my coins.

Units that came appeared to be new and unused, even though 2 had the thermal paste leaking problem which is the least, as they all were up and hashing within 5 mins of me plugging them in.

I will definately be buying more of these units.

Big up Mon.

ecury

newbie

Activity: 42

Merit: 0

Reading it all just made me happy i didn't buy any antminer from them.

Does it apply to Avalon as well? Or just Antimers?

SVK

sr. member

Activity: 378

Merit: 250

wttbs

legendary

Activity: 2210

Merit: 1109

I got me two miners, shipped to me this week. They are both used units, no just tested for a few hours but I guess they are used for hashing for almost a month. Production date is January 4th 2014. Grey thermal paste leaking from screws over the PCB and dust and dirt on/in the Fans. Not just a bit of loose dust: sticky dust you can't easily remove.

So Sushi and/or Bitmain, please be so honest to mention this on your sale topic or on your website, that you sell and ship USED units.

I cleaned the PCBs and the fans. Although they are used, they hash on 180GH/s without a problem, temp 46 degrees Celcius, not to much noise from the unit. Can't complain about that.

SVK

sr. member

Activity: 378

Merit: 250

Hi Sushi,
would love to know myself when we can order from you again Wink

jamesc760

sr. member

Activity: 448

Merit: 250

So, if you order an Antminer S1 unit from sushi today, what is the ETA? I'm asking because China is on new year holidays.

And, how/where do you go to make your order? Sorry for the question, but I'm a bit confused. Thanks in prior!

ts87233z

newbie

Activity: 3

Merit: 0

Hi Sushi,

Can i still have an antminer hosted for 0.5BTC

If so, I would like 2 please

Many thanks

elasticband

legendary

Activity: 1036

Merit: 1000

Nighty Night Don't Let The Trolls Bite Nom Nom Nom

Bitmain show me the email sushi sent me with he return address, you have 24hr to show me that screenshot or you sir are 100% a liar just like sushi.

If you want your crappy control board back give me a return address and pay for your own postage, as after the way you have dealt with this i am due you sweet fuck all...... you sir are an arsehole and have proved it by writing feedback based on what that rat sushi tells you. NO ONE HAS PROVIDED ME A RETURN ADDRESS FOR YOUR CONTROL BOARD.

SUSHI IS THE ONE WHO CAME ON TEAM VIEWER DECLARED THE BOARD DEAD AND SAID A NEW ONE WOULD BE SENT OUT, STOP BLAMING ME FOR YOUR SHITE COMMUNICATIONS

Show me a screenshot of the communication sent to my email address with the return address

novikov

newbie

Activity: 19

Merit: 0

Order # 100000436 2.5 BTC

TR ID: https://blockchain.info/tx/77ca8744e33c1ead542bdbe6f9f16f25dba5131c3cdd4fb0650ab375175d5199

Bitmainer + hosting ordered on 25.1. Want full refund.

BTC address:1NBwY2BycroF9icmerPQRQngoDZGN5By9j

Finansist

member

Activity: 64

Merit: 10

Solved

sushi

full member

Activity: 238

Merit: 100

ASIC Myth Buster

It was sent on Jan 23rd batch as promised. Tracking number x 2 were sent to you already.

I will PM them again just in case

Quote from: vadik on January 30, 2014, 06:59:20 AM

payment
https://blockchain.info/address/1H6AZn4JANQu9MMvH2QSTBgrCAhLdWsoMC

Order # Date Ship To Order Total Status
100000346 1/21/2014 ฿3.80 Processing View Order

did you send?
tracking number?
when?

ineedit

sr. member

Activity: 252

Merit: 250

Quote from: PaintShopPro6 on January 29, 2014, 10:48:16 PM

Quote from: Ridicuss on January 29, 2014, 07:19:38 PM

Quote from: Beans on January 29, 2014, 07:04:34 PM

A lot of mine came like this. Should I try to clean some of the paste off? Normally they don't come this bad.

...

I had one similar a couple months ago. It was quite messy and oozing from the bottom of the heatsink and board as well. I cleaned it the best I could with a small piece of thin plastic as a scraper, then I wiped it down with alcohol and clean the rest with a q-tip. The fasteners on my messy one were also loose, check those for tightness. If you are able to tighten them more compound will come out so you probably want to do that before you do your final clean up.

You absolutely must clean that off.

I have had 3 S1's arrive. I have spent 30 minutes, 20 minutes, and 15 minutes respectively cleaning each unit.

You WILL get short-circuits if you don't clean it up.

Secondly, there is an oil in the paste that is harder to see. You should clean that up too. It helps to blow a fan on it to dry some of it up.

Spend a bit of time cleaning, it is worth it. It is really hard to clean out from the resistors and such, but take your time, be careful, don't break anything.

There are two types of thermal paste or grease, electrically non-conductive thermal grease that includes silicone and zinc or electrically conductive that includes silver, copper, and aluminium. Bitmain uses a non-conductive thermal grease, you do not need to even need to remove it, it just looks prettier if you do

vadik

newbie

Activity: 2

Merit: 0

payment
https://blockchain.info/address/

Order # Date Ship To Order Total Status
100000346 1/21/2014 ฿3.80 Processing View Order

did you send?
tracking number?
when?

sushi

full member

Activity: 238

Merit: 100

ASIC Myth Buster

According to the factory, the paste is not conductive and it will not harm the chips but please wipe them as much as you can before using the Antminer!!!

That's the best I can do on this issue.

Quote from: Beans on January 29, 2014, 07:04:34 PM

A lot of mine came like this. Should I try to clean some of the paste off? Normally they don't come this bad.

sbfree

sr. member

Activity: 336

Merit: 250

Quote from: sushi on January 30, 2014, 04:43:16 AM

Thank you!!!

Quote from: sbfree on January 29, 2014, 07:50:42 PM

sushi, I need to leave you a tip....i have 15,000 dogecoins I would like to tip you with....since that is the new coin for tipping.

no problem, just need that dogecoin wallet address so i can send them.

sushi

full member

Activity: 238

Merit: 100

ASIC Myth Buster

Thank you!!!

Quote from: sbfree on January 29, 2014, 07:50:42 PM

sushi, I need to leave you a tip....i have 15,000 dogecoins I would like to tip you with....since that is the new coin for tipping.

PaintShopPro6

full member

Activity: 150

Merit: 100

Quote from: Ridicuss on January 29, 2014, 07:19:38 PM

Quote from: Beans on January 29, 2014, 07:04:34 PM

A lot of mine came like this. Should I try to clean some of the paste off? Normally they don't come this bad.

I had one similar a couple months ago. It was quite messy and oozing from the bottom of the heatsink and board as well. I cleaned it the best I could with a small piece of thin plastic as a scraper, then I wiped it down with alcohol and clean the rest with a q-tip. The fasteners on my messy one were also loose, check those for tightness. If you are able to tighten them more compound will come out so you probably want to do that before you do your final clean up.

You absolutely must clean that off.

I have had 3 S1's arrive. I have spent 30 minutes, 20 minutes, and 15 minutes respectively cleaning each unit.

You WILL get short-circuits if you don't clean it up.

Secondly, there is an oil in the paste that is harder to see. You should clean that up too. It helps to blow a fan on it to dry some of it up.

Spend a bit of time cleaning, it is worth it. It is really hard to clean out from the resistors and such, but take your time, be careful, don't break anything.

sbfree

sr. member

Activity: 336

Merit: 250

sushi, I need to leave you a tip....i have 15,000 dogecoins I would like to tip you with....since that is the new coin for tipping.

Ridicuss

sr. member

Activity: 336

Merit: 250

Quote from: Beans on January 29, 2014, 07:04:34 PM

A lot of mine came like this. Should I try to clean some of the paste off? Normally they don't come this bad.

I had one similar a couple months ago. It was quite messy and oozing from the bottom of the heatsink and board as well. I cleaned it the best I could with a small piece of thin plastic as a scraper, then I wiped it down with alcohol and clean the rest with a q-tip. The fasteners on my messy one were also loose, check those for tightness. If you are able to tighten them more compound will come out so you probably want to do that before you do your final clean up.

Topic: [GROUP BUY 7 OPEN] Antminer 180GH @ 1.90 BTC - Chinese End of the Year Sale - - page 3. (Read 23065 times)