GTX 1060 discussion thread - page 77.

teslakri

newbie

Activity: 1

Merit: 0

Quote from: antiycda on May 31, 2017, 06:59:57 PM

i have a problem abou the GTX 1060 3G eth mining hashrate. in win 7 it's working about 20 Mh/s but when i try to mining with win 10. this hashrate is droped only get 2.5 Mh/s. anyone get this problem ? btw My rx580 working
https://ip.bitcointalk.org/?u=https%3A%2F%2Fs7.postimg.org%2Fu37y4g9vt%2F1060.gif&t=577&c=DZ9-p7JPh9FY6Q

The solution is here https://www.youtube.com/watch?v=NvD57PyEJz8

newmz

sr. member

Activity: 372

Merit: 250

The road of excess leads to the palace of wisdom

I have 2 Galax 1060 6GB. It seems to me that when mining ETH overclocking the core is a waste of energy. If I set the memory to +750, it doesn't matter whether I have to core set to +75 or -250, I get the same hash rate of 22-23.

Igloczek

newbie

Activity: 2

Merit: 0

@PanneKopp actually my 1060-3 mine faster than yours 1060-6

It takes 305W from the wall (with more powerful CPU), but eletricicty cost only 0.10$/kWh, so I don't care about trimming down power consumption that much.

https://i.imgur.com/sbi7Byc.png

preda

sr. member

Activity: 756

Merit: 250

guys look what a 1060 3gb cheap cost can do!!!!

23.5 with lowww power

https://youtu.be/1uhSfOpvHks?t=7359

kapsel

member

Activity: 60

Merit: 10

I got ASUS DUAL 6GB cards so far I have tested lbry, eth, zec and skein, for most algos 55-60% power limit seems to be the place for highest efficiency, the cards have 120w TDP. I'm at work and writing results off the top of my head, might not be fully accurate. I found skein to be most profitable at this moment.

ETH 24 mh/s with memory at +1000 mhz(9600 mhz, claymore)
ZEC 300 sol/s 75% power limit, +260 core/400 memory(EWBF)
DGB-skein - 350mh/s - 65% power limit, +260 core, -500 memory(alexis78 ccminer)
LBC 190 mh/s 60% power limit, +260 core, -500 memory(ccminer 2.0 tpruvot)

preda

sr. member

Activity: 756

Merit: 250

I got 12x zotac and gigabyte 1060 3gb price 177/180 euro

Easily oc with msi afterburner +100 core + 950 memory
Temp 70
Hasharate 23.5 eth
Draining 90w

Cost hashrate is about 7.53 euro mh not bad at all!!!

PanneKopp

sr. member

Activity: 391

Merit: 250

aka ...

Quote from: PanneKopp on May 31, 2017, 05:16:06 AM

I won´t recommend the GTX-1060 with 3 GB because they have a lower bandwidth memory interface and usually lower base/boost-clocks.

Hi @antiycda,

third thread here with your probs ?

Nobody can help, if you don´t give full information.

Quote from: MrN1ce9uy on June 02, 2017, 11:41:36 AM

What are your other GPUs?

What miner do you use ?

xD

P.S. I won´t mix NVidia and AMD in one RIG, I even tend not 2 mix any different cards (no matter what - but all the same pls.)

MrN1ce9uy

member

Activity: 155

Merit: 11

Quote from: antiycda on May 31, 2017, 06:59:57 PM

i have a problem abou the GTX 1060 3G eth mining hashrate. in win 7 it's working about 20 Mh/s but when i try to mining with win 10. this hashrate is droped only get 2.5 Mh/s. anyone get this problem ? btw My rx580 working

What are your other GPUs?

antiycda

full member

Activity: 140

Merit: 100

i have a problem abou the GTX 1060 3G eth mining hashrate. in win 7 it's working about 20 Mh/s but when i try to mining with win 10. this hashrate is droped only get 2.5 Mh/s. anyone get this problem ? btw My rx580 working

PanneKopp

sr. member

Activity: 391

Merit: 250

aka ...

I won´t recommend the GTX-1060 with 3 GB because they have less cuda-cores, a lower bandwidth memory interface and usually lower base/boost-clocks.

I have build a small rig with 2 GTX-1060-6:

no case yet (gonna choose a cheap ATX Midtower with at least 3 120mm intake (!) fans)
460W PSU
ASRock B150M mainboard (space between the two PCI-E ist important)
2 x DDR4 4GB
120GB SSD
2 x KFA2 (Galaxy) GTX-1060-6 OC (non EX)

Win7_64
NHM v1.7.5.12

trimmed down to 230W from wall (= 1.44 EUR/day at 0.26 EUR/KWh)

... should ROI rel. fast even at my high power costs

Grin

promomei

sr. member

Activity: 399

Merit: 254

Hello miners
How is MSI GTX 1060 GAMING X 6G for mining Zcash and Eth on windows 8
and you know any pools for it
Thanks

LeviathanEatingShibe

newbie

Activity: 5

Merit: 0

Quote from: m1n1ngP4d4w4n on January 04, 2017, 07:32:21 PM

Quote from: LeviathanEatingShibe on January 04, 2017, 07:12:11 PM

I have a GTX 1060 6GB, I'm getting 560 h/s MAX (any more and I get ye old CPU does not validate) I have some more details about my rig in this thread https://bitcointalk.org/index.php?topic=1739438.new#new - I think there's some sort of far away hidden setting I must've enabled that just made my GPU about 100x weaker (though it runs games amazingly, so I don't understand why mining is so bad?) If someone could tell me exactly how I managed to mess up so badly that I get 500 h/s on a card that's supposed to get 1+ megahash per second, it would be greatly appreciated.

where did you see one GTX 1060 will do 1+ megahash Oo in either XMR or Zcash that's just not possible

Up above the world so high, miners with the same graphics card getting well over 1MH/s - I've only tried a few algorithms so far, mainly Scrypt and Cryptonight, and a few others my minors supported and I got roughly the same Kh/s every time - I'll try out Ethereum and see if I get anywhere close to a megahash, but it would be pretty sucky to get 30 Megahashes in one currency, and 550 kh/s in another, and sounds almost impossible without interfering with your PC's resources?

Edit: Just started mining Ethereum and I understand what you meant by they're different, I haven't done any config changes (yet) but I'm getting roughly 18 MH/s

So now that we've got that cleared - carrying on with this threads base theme, what are your hashrates when mining Scrypt / Cryptonight?

m1n1ngP4d4w4n

full member

Activity: 224

Merit: 100

CryptoLearner

Quote from: LeviathanEatingShibe on January 04, 2017, 07:12:11 PM

I have a GTX 1060 6GB, I'm getting 560 h/s MAX (any more and I get ye old CPU does not validate) I have some more details about my rig in this thread https://bitcointalk.org/index.php?topic=1739438.new#new - I think there's some sort of far away hidden setting I must've enabled that just made my GPU about 100x weaker (though it runs games amazingly, so I don't understand why mining is so bad?) If someone could tell me exactly how I managed to mess up so badly that I get 500 h/s on a card that's supposed to get 1+ megahash per second, it would be greatly appreciated.

where did you see one GTX 1060 will do 1+ megahash Oo in either XMR or Zcash that's just not possible

LeviathanEatingShibe

newbie

Activity: 5

Merit: 0

I have a GTX 1060 6GB, I'm getting 560 h/s MAX (any more and I get ye old CPU does not validate) I have some more details about my rig in this thread https://bitcointalk.org/index.php?topic=1739438.new#new - I think there's some sort of far away hidden setting I must've enabled that just made my GPU about 100x weaker (though it runs games amazingly, so I don't understand why mining is so bad?) If someone could tell me exactly how I managed to mess up so badly that I get 500 h/s on a card that's supposed to get 1+ megahash per second, it would be greatly appreciated.

k0stas

hero member

Activity: 526

Merit: 502

My new cart palit 1060 gtx 3gb mining ethereum with claymore's miner on windows 7 at stock 19Mh/s and with oc 21Mh/s
with -ethi 7 (default is 8 ) pic.

Amph

legendary

Activity: 3248

Merit: 1070

Quote from: cptfisher on October 04, 2016, 09:38:35 AM

well that is a lot... a 1070 could do easily 214 with 65 watt

yeah i was expecting less to be honest surely under 100, on the other hand a 1060 costs almost half of a 1070, not the 6gb though

cptfisher

hero member

Activity: 649

Merit: 505

well that is a lot... a 1070 could do easily 214 with 65 watt

anorganix

copper member

Activity: 970

Merit: 287

Per aspera ad astra

Yes, it's the 6GB version.
I've set 85% power limit to stay near 100W and I'm pulling a constant 200 - 201 MH/s.

Amph

legendary

Activity: 3248

Merit: 1070

Quote from: anorganix on October 04, 2016, 02:46:30 AM

Gigabyte GeForce GTX 1060 6GB WindForce:

lbry @ 201 MH/s with 85% power limit / +230 Mhz core / -502 Mhz memory
neoscrypt @ 810 kH/s with 105% power limit / +185 Mhz core / +795 Mhz memory (can go even more since it's Samsung memory)
dagger hashimoto @ 23 MH/s but I can't remember the settings 100% accurately

200MH is good for a card that cost half of the 1070, but what about consumption?

ah your is the 6gb version, not exactly half of the 1070, would be nice to have the 3gb version hash power

anorganix

copper member

Activity: 970

Merit: 287

Per aspera ad astra

Gigabyte GeForce GTX 1060 6GB WindForce:

lbry @ 201 MH/s with 85% power limit / +230 Mhz core / -502 Mhz memory
neoscrypt @ 810 kH/s with 105% power limit / +185 Mhz core / +795 Mhz memory (can go even more since it's Samsung memory)
dagger hashimoto @ 23 MH/s but I can't remember the settings 100% accurately

Topic: GTX 1060 discussion thread - page 77. (Read 289429 times)