Pages:
Author

Topic: lolMiner 1.64: Fastest Kaspa miner in market - page 30. (Read 155842 times)

member
Activity: 91
Merit: 10
I`m testing lolminer for the first time to unlock 3060 potential.
It`s not working on 455.45.01 - 2 rigs - same.
I`ll try newer driver
https://imgur.com/oNqncYF

Update:
Same settings, just driver change
https://imgur.com/robPNfZ

It  is normal... it nearly takes 5-6 minutes to complete get full Mhs in the 3060... Just wait a little bit. You can also put your OC to see the results...

I'm getting more than 37Mhs without an aggresive OC



You missunderstand me.
24mhash is not a good sign. After upgrade to 460 - works fine.
It runs at 37,6Mhash.
legendary
Activity: 4256
Merit: 8551
'The right to privacy matters'
I`m testing lolminer for the first time to unlock 3060 potential.
It`s not working on 455.45.01 - 2 rigs - same.
I`ll try newer driver
https://imgur.com/oNqncYF

Update:
Same settings, just driver change
https://imgur.com/robPNfZ

It  is normal... it nearly takes 5-6 minutes to complete get full Mhs in the 3060... Just wait a little bit. You can also put your OC to see the results...

I'm getting more than 37Mhs without an aggresive OC




yeah I am doing about the same.

you can lower ram to 1900 and its about the same numbers but the ram runs cooler.

at the op nice work.
member
Activity: 639
Merit: 19
I`m testing lolminer for the first time to unlock 3060 potential.
It`s not working on 455.45.01 - 2 rigs - same.
I`ll try newer driver
https://imgur.com/oNqncYF

Update:
Same settings, just driver change
https://imgur.com/robPNfZ

It  is normal... it nearly takes 5-6 minutes to complete get full Mhs in the 3060... Just wait a little bit. You can also put your OC to see the results...

I'm getting more than 37Mhs without an aggresive OC


member
Activity: 91
Merit: 10
I`m testing lolminer for the first time to unlock 3060 potential.
It`s not working on 455.45.01 - 2 rigs - same.
I`ll try newer driver
https://imgur.com/oNqncYF

Update:
Same settings, just driver change
https://imgur.com/robPNfZ
member
Activity: 113
Merit: 10
definitely interested to see how this will work with the LHR cards to be released soonish

LHR cards will require a new driver
The developer just stated this trick won't work on new drivers
Don't hold your breath
sr. member
Activity: 703
Merit: 272
Sry for the long silence here, but well - jgonzi took over a lot of the support needed here.

But today want to announce something new - and kind of special:

lolMiner 1.29 brings a partial unlock for you RTX 3060 users!

Partial here means that it is not able to get the full 48 mh out of the card, but at least some good way up from the known barrier (approx 36 mh). And different from existing Windows solutions this here has some advantages:
- Risers are no issue
- No screen or fake hdmi needed
- No limitation on the number of GPUs
- It works in your favorite Linux mining OS

Only requirement it has: you need to run Nvidia Cuda drivers 455.45.01 to 460.39 - newer drivers have a changed lock mechanism and are not so easy to trick.
Have fun mining!

definitely interested to see how this will work with the LHR cards to be released soonish
member
Activity: 155
Merit: 14
lolMiner 1.29 brings a partial unlock for you RTX 3060 users!

Partial here means that it is not able to get the full 48 mh out of the card, but at least some good way up from the known barrier (approx 36 mh). And different from existing Windows solutions this here has some advantages:
- Risers are no issue
- No screen or fake hdmi needed
- No limitation on the number of GPUs
- It works in your favorite Linux mining OS

Only requirement it has: you need to run Nvidia Cuda drivers 455.45.01 to 460.39 - newer drivers have a changed lock mechanism and are not so easy to trick.
Have fun mining!

That's great.
ChumpChangeXD just released a video where you see 6x 3060s with higher hashrates.
https://www.youtube.com/watch?v=ruu6jf7i63I
member
Activity: 433
Merit: 48
Sry for the long silence here, but well - jgonzi took over a lot of the support needed here.

But today want to announce something new - and kind of special:

lolMiner 1.29 brings a partial unlock for you RTX 3060 users!

Partial here means that it is not able to get the full 48 mh out of the card, but at least some good way up from the known barrier (approx 36 mh). And different from existing Windows solutions this here has some advantages:
- Risers are no issue
- No screen or fake hdmi needed
- No limitation on the number of GPUs
- It works in your favorite Linux mining OS

Only requirement it has: you need to run Nvidia Cuda drivers 455.45.01 to 460.39 - newer drivers have a changed lock mechanism and are not so easy to trick.
Have fun mining!
member
Activity: 639
Merit: 19
lolminer 1.28a linux
AMD R9 390 ~ 6 cards per rig
mining to nanopool

Getting over 100 errors per card? The miner attempts to fix them but with that many errors it takes too long.

I tried it with --disable-dag-verify but I think there are still errors because my hashrate at the pool seems low.
Switching back to version 1.26

the hash rate to the people takes some time and the average come later... it could be that for R390 it wasn't correctly optimized the dag verify.

Yes it does take some time for the pool to get a decent average, and to be fair I didn't let them run a long time.  After so many errors being reported I was skeptical and without knowing if it's a problem with the verification process or if it was the DAG build process.

I'll switch one of the rigs back over to version 1.28 with --disable-dag-verify and let it run 6 hours or so...

Also, would like to thank the OP for a miner that still supports these old AMD R9 390 cards. I have several rigs full of them.

They consume Watts but they are incredible Cards!!! for the lot of years they have!! Nice RIGS!!
newbie
Activity: 6
Merit: 0
lolminer 1.28a linux
AMD R9 390 ~ 6 cards per rig
mining to nanopool

Getting over 100 errors per card? The miner attempts to fix them but with that many errors it takes too long.

I tried it with --disable-dag-verify but I think there are still errors because my hashrate at the pool seems low.
Switching back to version 1.26

the hash rate to the people takes some time and the average come later... it could be that for R390 it wasn't correctly optimized the dag verify.

Yes it does take some time for the pool to get a decent average, and to be fair I didn't let them run a long time.  After so many errors being reported I was skeptical and without knowing if it's a problem with the verification process or if it was the DAG build process.

I'll switch one of the rigs back over to version 1.28 with --disable-dag-verify and let it run 6 hours or so...

Also, would like to thank the OP for a miner that still supports these old AMD R9 390 cards. I have several rigs full of them.
member
Activity: 639
Merit: 19
lolminer 1.28a linux
AMD R9 390 ~ 6 cards per rig
mining to nanopool

Getting over 100 errors per card? The miner attempts to fix them but with that many errors it takes too long.

I tried it with --disable-dag-verify but I think there are still errors because my hashrate at the pool seems low.
Switching back to version 1.26

the hash rate to the people takes some time and the average come later... it could be that for R390 it wasn't correctly optimized the dag verify.
newbie
Activity: 6
Merit: 0
lolminer 1.28a linux
AMD R9 390 ~ 6 cards per rig
mining to nanopool

Getting over 100 errors per card? The miner attempts to fix them but with that many errors it takes too long.

I tried it with --disable-dag-verify but I think there are still errors because my hashrate at the pool seems low.
Switching back to version 1.26
member
Activity: 639
Merit: 19
Using 1.28a. Epoch 414 came up, and stale shares were flying. Restarting Lolminer did not help.

Rolled back to 1.26 and everything back to normal.

Which is great, but now I miss the auto-restart option of 1.28. Hope OP can look into it?

Where were you mining? It could be the ethermine.org crash. I have it in all my rigs too yesterday.  And later I saw was ethermine.org  fail, he also announced in the webpage
newbie
Activity: 1
Merit: 0
Using 1.28a. Epoch 414 came up, and stale shares were flying. Restarting Lolminer did not help.

Rolled back to 1.26 and everything back to normal.

Which is great, but now I miss the auto-restart option of 1.28. Hope OP can look into it?

---

Edit: idd, ethermine was to blame. Just a coincidence that the minute I roll-back, ethermine came back up   Cool
jr. member
Activity: 152
Merit: 8
Hello!

Could someone explain me that thing: same rig , same setup, same OS

Celeron G3930 CPU installed - 24.2 Mhs one RX474 PCIex 16x
Pentium G4650T CPU installed - 20.2 Mhs one RX474 PCIex 16x

Pentium has more cash , more Mhz, more threads , but how .....

Im so confused!!!

It seems one is Gen3 and the other Gen2... Could it be?

Well,dont know exectly , going to make some tests today. But why it depends so much of CPU type? Especially if both CPUs almost the same arhitecture.
member
Activity: 639
Merit: 19
Hello,

  I want to know that the 1.28a stable or not?  I want to upgrade lolMiner version.

I am using lolMiner Linux old version with some RX470 and NVidia 1070.

If it works don't touch 😅
member
Activity: 639
Merit: 19
Hello!

Could someone explain me that thing: same rig , same setup, same OS

Celeron G3930 CPU installed - 24.2 Mhs one RX474 PCIex 16x
Pentium G4650T CPU installed - 20.2 Mhs one RX474 PCIex 16x

Pentium has more cash , more Mhz, more threads , but how .....

Im so confused!!!

It seems one is Gen3 and the other Gen2... Could it be?
jr. member
Activity: 152
Merit: 8
Hello!

Could someone explain me that thing: same rig , same setup, same OS

Celeron G3930 CPU installed - 24.2 Mhs one RX474 PCIex 16x
Pentium G4650T CPU installed - 20.2 Mhs one RX474 PCIex 16x

Pentium has more cash , more Mhz, more threads , but how .....

Im so confused!!!
jr. member
Activity: 119
Merit: 3
Hello o7

OS:Windows 10 Pro
Miner: 1.28

Number of OpenCL supported GPUs: 2
Cuda driver detected.
Number of Cuda supported GPUs: 2
Device 0:
    Name:    NVIDIA GeForce GTX 1060 3GB
    Address: 1:0
    Vendor:  NVIDIA Corporation
    Drivers: Cuda, OpenCL
    Memory:  3072 MByte
    Active:  false (OpenCL init failure: Memory object allocation failure)
......................
the other one (device 1) it is irelevant because i select the Device 0 what it is free and dedicate only to mining
......................
All devices deselected or failed compatiblity check. Closing lolMiner

The issue is Miner it FAIL to run 192.7 Algo aka it fail mine ZLC when that it suppose to require max 2600 VRAM for frack sake ....
Command what i used: lolMiner.exe --devices 0 --coin AUTO192_7 --pool !POOL! --user !WALLET! --pass c=BTG,mc=VDL/YEC/ZCL,ID=Bx60
I mine yesterday with MiniZ (app) on same condition perfectly ... so i see miner it have multiple issue aka ETC fail to run on Win 10 aka "GPU 0: error when allocating memory or building DAG. Disabling card."

Same issue it have gminer to ... it fail to run on win 10 pro when it suppose to run perfectly soo i don't know what it is going on but for sure it is a issue, probabil nobody it will care to fix but still i rise a hand and point ...

prof Windows 10 Pro it have inaff Vram to run 192.7 Algo



cheers
newbie
Activity: 45
Merit: 0
Hello,

  I want to know that the 1.28a stable or not?  I want to upgrade lolMiner version.

I am using lolMiner Linux old version with some RX470 and NVidia 1070.
Pages:
Jump to: