Open Source XPM (Primecoin) GPU Miner & Pool xpmforall.org - page 32.

soulmann

full member

Activity: 221

Merit: 100

Quote from: abrgeza on March 17, 2018, 05:46:59 PM

Quote from: soulmann on March 17, 2018, 05:43:40 PM

The powerlimit "-1" in config file actually changes powerlimit to -1. I reset all settings to default in msi afterburner, then start xpmclient, then i check the msi afterburner and PL is -1.

just put "+0" instead "-1"

Yes I did it. I just want to say that description is wrong about PL in config.

Romeo53

newbie

Activity: 6

Merit: 0

http://xpm.muuttuja.org/calc/ show me 8.29 XPM per day from 28.5 CPD. is it true what i will earn 5.5$ per day from my 70 (390,480) gpus? i won't pay electricity from that

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: Romeo53 on March 17, 2018, 05:28:26 PM

win 8.1 64bit. at same win works 10 farms, and at same drivers. before it works with 9.4.1 version, but after i update driver, it show me this error. i uninstall with Display driver uninstaller, and reinstall drivers. but same error

amd or nvidia gpu?

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: soulmann on March 17, 2018, 05:43:40 PM

The powerlimit "-1" in config file actually changes powerlimit to -1. I reset all settings to default in msi afterburner, then start xpmclient, then i check the msi afterburner and PL is -1.

just put "+0" instead "-1"

soulmann

full member

Activity: 221

Merit: 100

The powerlimit "-1" in config file actually changes powerlimit to -1. I reset all settings to default in msi afterburner, then start xpmclient, then i check the msi afterburner and PL is -1.

Romeo53

newbie

Activity: 6

Merit: 0

win 8.1 64bit. at same win works 10 farms, and at same drivers. before it works with 9.4.1 version, but after i update driver, it show me this error. i uninstall with Display driver uninstaller, and reinstall drivers. but same error

eXtremal

sr. member

Activity: 2106

Merit: 282

👉bit.ly/3QXp3oh | 🔥 Ultimate Launc

Quote from: Romeo53 on March 17, 2018, 03:33:07 PM

why i get error "64 bit kernels not supported on 32 bit executable"?

i try different drivers. 15.2, 16.3 etc

What type of Win10 you use, 32 bit or 64 bit ?

Romeo53

newbie

Activity: 6

Merit: 0

why i get error "64 bit kernels not supported on 32 bit executable"?
http://www.picshare.ru/uploads/180318/LfRlauivgD.jpg
i try different drivers. 15.2, 16.3 etc

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: soulmann on March 17, 2018, 07:19:34 AM

Quote from: abrgeza on March 17, 2018, 02:17:15 AM

Quote from: eXtremal on March 16, 2018, 09:41:12 PM

How you did it ?

it took me 10hr to find best combination for those cards and it is client10.2.1 and driver 16.9.2

Windows 10? Creators or anniversary?

Win10Pro, version 1709, OS Build 16299.309

soulmann

full member

Activity: 221

Merit: 100

Quote from: abrgeza on March 17, 2018, 02:17:15 AM

Quote from: eXtremal on March 16, 2018, 09:41:12 PM

How you did it ?

it took me 10hr to find best combination for those cards and it is client10.2.1 and driver 16.9.2

Windows 10? Creators or anniversary?

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: eXtremal on March 16, 2018, 09:41:12 PM

How you did it ?

it took me 10hr to find best combination for those cards and it is client10.2.1 and driver 16.9.2

eXtremal

sr. member

Activity: 2106

Merit: 282

👉bit.ly/3QXp3oh | 🔥 Ultimate Launc

Quote from: abrgeza on March 16, 2018, 03:56:02 AM

Update:
Finally I got it to work!
It should be equal to 10.5-11cpd with target=10

Code:

[GPU 0] T=43C A=98% E=0 primes=0.104222 fermat=280227/sec cpd=0.38/day
[GPU 1] T=52C A=100% E=0 primes=0.104251 fermat=281815/sec cpd=0.38/day
[GPU 2] T=55C A=100% E=0 primes=0.104241 fermat=281928/sec cpd=0.38/day
[GPU 3] T=54C A=100% E=0 primes=0.104312 fermat=281100/sec cpd=0.39/day
[GPU 4] T=59C A=100% E=0 primes=0.104093 fermat=280431/sec cpd=0.38/day
[GPU 5] T=48C A=100% E=0 primes=0.104254 fermat=280590/sec cpd=0.38/day
(ST/INV/DUP): 1316x 7ch(1/43/7) 128x 8ch(1/7/0) 12x 9ch(0/0/0) 2x 10ch(0/0/0) 1x 11ch(0/0/0)

@eXtremal
Thank you for your excellent 10.2.1 client.

How you did it ?

Quote from: Romeo53 on March 16, 2018, 04:17:36 PM

why compiled win 10.2.1 version i can't find. extremal, is it difficult to do it? or you think all there mega programists? any body compile this, i lost a lot of time to try do it. mingw get error could not find protobuf

Compiled windows version is archive http://coinsforall.io/distr/xpmclient-10.2.1-beta.tar.gz name xpmclient.exe
If you don't want use released binary and want compile, you need download and build google protobuf before and some other libraries mentioned in readme.

Quote from: tar1s on March 16, 2018, 05:52:18 PM

To update statistics(target="11"):
Win 10
xpmclient v.10.2
Vega 56 (bios from wet 64), driver 18.2.3 - 0.66 cpd
xpmclient v.9.4.1
R9 390, driver 18.2.3 - 0.34(35) cpd
RX 480, driver Blockchain-Aug23 - 0.35(36) cpd
RX 580, driver 17.7 - 0.39(40) cpd

Vega and Polaris good results for target="11", I have stock Vega 56 with 0.61 cpd only

R9 390 too low CPD, I don't know how get 0.5 CPD with 18.2 drivers (may be run from separate directore and use old OCL?)

tar1s

jr. member

Activity: 40

Merit: 1

To update statistics(target="11"):
Win 10
xpmclient v.10.2
Vega 56 (bios from wet 64), driver 18.2.3 - 0.66 cpd
xpmclient v.9.4.1
R9 390, driver 18.2.3 - 0.34(35) cpd
RX 480, driver Blockchain-Aug23 - 0.35(36) cpd
RX 580, driver 17.7 - 0.39(40) cpd

Romeo53

newbie

Activity: 6

Merit: 0

why compiled win 10.2.1 version i can't find. extremal, is it difficult to do it? or you think all there mega programists? any body compile this, i lost a lot of time to try do it. mingw get error could not find protobuf
http://www.picshare.ru/uploads/180317/1NiXJmkTfm.jpg

buny

full member

Activity: 237

Merit: 100

I'm at a loss ... why there is no indignation? that the pool steals ... that the miner is bad?! Grin

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: eXtremal on March 16, 2018, 03:50:29 AM

abrgeza
Can you try xpmclient 10.2.1 with drivers 15.12 and OCL from 13.x/14.x ?

none version xpmclient won't start with ocl 14.x
i can give you access to my computer via teamviewer so you can test anything.

Update:
Finally I got it to work!
It should be equal to 10.5-11cpd with target=10

Code:

[GPU 0] T=43C A=98% E=0 primes=0.104222 fermat=280227/sec cpd=0.38/day
[GPU 1] T=52C A=100% E=0 primes=0.104251 fermat=281815/sec cpd=0.38/day
[GPU 2] T=55C A=100% E=0 primes=0.104241 fermat=281928/sec cpd=0.38/day
[GPU 3] T=54C A=100% E=0 primes=0.104312 fermat=281100/sec cpd=0.39/day
[GPU 4] T=59C A=100% E=0 primes=0.104093 fermat=280431/sec cpd=0.38/day
[GPU 5] T=48C A=100% E=0 primes=0.104254 fermat=280590/sec cpd=0.38/day
(ST/INV/DUP): 1316x 7ch(1/43/7) 128x 8ch(1/7/0) 12x 9ch(0/0/0) 2x 10ch(0/0/0) 1x 11ch(0/0/0)

@eXtremal
Thank you for your excellent 10.2.1 client.

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: eXtremal on March 16, 2018, 03:30:15 AM

Quote from: abrgeza on March 16, 2018, 02:38:56 AM

let's make some benchmarks.

It's known information, you can't get good CPD with 15.12, need OCL from 14.x. This substitution works well on Windows 7 and Linux, but may not properly works on Windows 10.

Here is collection of OCL part from different drivers:
http://cryptomining-blog.com/tag/amd-opencl/
Direct link: http://cryptomining-blog.com/wp-content/download/amd-opencl-driver-versions.zip

i have good CPD with 15.12 and stock kernel (target=10).
it is more or less same CPD compared to win7 with 14.6 driver.

eXtremal

sr. member

Activity: 2106

Merit: 282

👉bit.ly/3QXp3oh | 🔥 Ultimate Launc

abrgeza
Can you try xpmclient 10.2.1 with drivers 15.12 and OCL from 13.x/14.x ?

eXtremal

sr. member

Activity: 2106

Merit: 282

👉bit.ly/3QXp3oh | 🔥 Ultimate Launc

Quote from: abrgeza on March 16, 2018, 02:38:56 AM

let's make some benchmarks.

It's known information, you can't get good CPD with 15.12, need OCL from 14.x. This substitution works well on Windows 7 and Linux, but may not properly works on Windows 10.

Here is collection of OCL part from different drivers:
http://cryptomining-blog.com/tag/amd-opencl/
Direct link: http://cryptomining-blog.com/wp-content/download/amd-opencl-driver-versions.zip

abrgeza

jr. member

Activity: 117

Merit: 2

Quote from: eXtremal on March 16, 2018, 02:12:31 AM

Quote from: abrgeza on March 16, 2018, 12:26:00 AM

sure

What with shared kernel for 11ch ?

let's make some benchmarks.

win10, driver15,12, xpmclient9.4.1, target=10, stock kernel

Code:

[GPU 0] T=62C A=100% E=0 primes=0.105017 fermat=849046/sec cpd=11.97/day
[GPU 1] T=65C A=99% E=0 primes=0.104818 fermat=784899/sec cpd=10.86/day
[GPU 2] T=61C A=100% E=0 primes=0.105001 fermat=784686/sec cpd=11.04/day
[GPU 3] T=62C A=100% E=0 primes=0.104707 fermat=785308/sec cpd=10.75/day
[GPU 4] T=65C A=98% E=0 primes=0.104883 fermat=850010/sec cpd=11.83/day
[GPU 5] T=60C A=99% E=0 primes=0.105033 fermat=782876/sec cpd=11.05/day

win10, driver15,12, xpmclient9.4.1, target=11, kernel compiled with driver15.12

Code:

[GPU 0] T=57C A=100% E=0 primes=0.104122 fermat=216207/sec cpd=0.29/day
[GPU 1] T=65C A=100% E=0 primes=0.104205 fermat=190936/sec cpd=0.26/day
[GPU 2] T=56C A=100% E=0 primes=0.104362 fermat=193914/sec cpd=0.27/day
[GPU 3] T=58C A=85% E=0 primes=0.104075 fermat=193390/sec cpd=0.26/day
[GPU 4] T=59C A=90% E=0 primes=0.104545 fermat=216964/sec cpd=0.31/day
[GPU 5] T=56C A=100% E=0 primes=0.104436 fermat=194074/sec cpd=0.27/day

win10, driver15,12, xpmclient9.4.1, target=11, new shared kernel

Code:

[GPU 0] T=61C A=98% E=0 primes=0.096796 fermat=258781/sec cpd=0.16/day
[GPU 1] T=69C A=100% E=0 primes=0.097169 fermat=250600/sec cpd=0.16/day
[GPU 2] T=61C A=100% E=0 primes=0.097174 fermat=250774/sec cpd=0.16/day
[GPU 3] T=62C A=99% E=0 primes=0.096406 fermat=251328/sec cpd=0.15/day
[GPU 4] T=63C A=100% E=0 primes=0.097970 fermat=261023/sec cpd=0.18/day
[GPU 5] T=59C A=100% E=0 primes=0.096811 fermat=251608/sec cpd=0.15/day

Topic: Open Source XPM (Primecoin) GPU Miner & Pool xpmforall.org - page 32. (Read 110186 times)