Topic: Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 35. (Read 104914 times)
My package has not left Sofia for a couple days. Is this normal?
what I am but wonder
when I log in (mr-3020)
under Status
Am I missing "status cgminer"
when I log in (mr-3020)
under Status
Am I missing "status cgminer"
Yes, but not only you. All image from technobit come with no cgminer status
since all available on cgminer api log
what I am but wonder
when I log in (mr-3020)
under Status
Am I missing "status cgminer"
Great
when I log in (mr-3020)
under Status
Am I missing "status cgminer"
thank you that it was apparently
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
get under SSH screen-r this error message
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
Great
thank you that it was apparently
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
get under SSH screen-r this error message
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
Great
.......
Well, I tried both PCIe Ports and also CPU 4 Pin, but one board is still running at ~15GH.
In order to be sure, I tried the board alone, same situation as with all 3 boards.
I will try to get my hands on a second PSU, maybe it will help.
Thanks anyway
Marto, any clue?
Edit: I tried with an extra PSU (16A) just for this one board, same result
Well, I tried both PCIe Ports and also CPU 4 Pin, but one board is still running at ~15GH.
In order to be sure, I tried the board alone, same situation as with all 3 boards.
I will try to get my hands on a second PSU, maybe it will help.
Thanks anyway
Marto, any clue?
Edit: I tried with an extra PSU (16A) just for this one board, same result
Sound like faulty 4 chips but not so sure. If only your TL-MR3020 not bricked, you can check each chip status in cgminer api log.
thank you that it was apparently
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
get under SSH screen-r this error message
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
Pi is totally stressed out with all 3 boards, not possible to get them up running.
On Ubuntu, I managed to get all 3 boards running, but after 8 hours, the PSU stopped, I guess it went in protection mode.
One board only ran with 15GH/s, so I guess it is not getting enough power and this caused that the PSU stopped.
Right now, this one board doesn't even start and shows 0 GH/s in cgminer.
My PSU (be quiet! Straight Power E9 700W ATX 2.31) has 4 rails, but which rail do I have to use?:
I think at the moment I do have two boards connected to HDD wire, which I guess do not serve enough power
12V1-18A --> HDD/SATA?
12V2-18A --> 24Pin?
12V3-22A --> PCIe1?
12V4-22A --> PCIe2?
Anyone can help me, do you think this is right?
Maybe, then V1 rail definely won't be able to supply 2 board for long time. My kyoritsu clampmeter show about 9 A DC used by single HEX16C.
So you need to devided all three board on V1, V3, V4.
Good luck
Well, I tried both PCIe Ports and also CPU 4 Pin, but one board is still running at ~15GH.
In order to be sure, I tried the board alone, same situation as with all 3 boards.
I will try to get my hands on a second PSU, maybe it will help.
Thanks anyway
Marto, any clue?
Edit: I tried with an extra PSU (16A) just for this one board, same result
Clock and voltage please. Leave the board for at least 24 hours to minimize variance.
Clock is 1500 and voltage is 1100
Thx!
Hello there
I have 6 units hex16a2, and one of them has some problem, when i start cgminer on router this one always shuts down, i´ve tryed another usb cabe and another usb port on hub, and it remains the same, is there something i can do at hardware level ?? I mean check some component or make some solder ? That´s because if i have to send it to Marto / Technobit it will take ages to arrive to me again
Faulty USB connector on the board?I have 6 units hex16a2, and one of them has some problem, when i start cgminer on router this one always shuts down, i´ve tryed another usb cabe and another usb port on hub, and it remains the same, is there something i can do at hardware level ?? I mean check some component or make some solder ? That´s because if i have to send it to Marto / Technobit it will take ages to arrive to me again
Can you try just this board connected directly to USB of the router without hub?
Today i will try this board connected to windows only ... i may try to replace the conector also but that could remove warranty i have several connectors like that ones cause i make gsm repairs
Hello there
I have 6 units hex16a2, and one of them has some problem, when i start cgminer on router this one always shuts down, i´ve tryed another usb cabe and another usb port on hub, and it remains the same, is there something i can do at hardware level ?? I mean check some component or make some solder ? That´s because if i have to send it to Marto / Technobit it will take ages to arrive to me again
Faulty USB connector on the board?I have 6 units hex16a2, and one of them has some problem, when i start cgminer on router this one always shuts down, i´ve tryed another usb cabe and another usb port on hub, and it remains the same, is there something i can do at hardware level ?? I mean check some component or make some solder ? That´s because if i have to send it to Marto / Technobit it will take ages to arrive to me again
Can you try just this board connected directly to USB of the router without hub?
Hello there
I have 6 units hex16a2, and one of them has some problem, when i start cgminer on router this one always shuts down, i´ve tryed another usb cabe and another usb port on hub, and it remains the same, is there something i can do at hardware level ?? I mean check some component or make some solder ? That´s because if i have to send it to Marto / Technobit it will take ages to arrive to me again
I have 6 units hex16a2, and one of them has some problem, when i start cgminer on router this one always shuts down, i´ve tryed another usb cabe and another usb port on hub, and it remains the same, is there something i can do at hardware level ?? I mean check some component or make some solder ? That´s because if i have to send it to Marto / Technobit it will take ages to arrive to me again
Pi is totally stressed out with all 3 boards, not possible to get them up running.
On Ubuntu, I managed to get all 3 boards running, but after 8 hours, the PSU stopped, I guess it went in protection mode.
One board only ran with 15GH/s, so I guess it is not getting enough power and this caused that the PSU stopped.
Right now, this one board doesn't even start and shows 0 GH/s in cgminer.
My PSU (be quiet! Straight Power E9 700W ATX 2.31) has 4 rails, but which rail do I have to use?:
I think at the moment I do have two boards connected to HDD wire, which I guess do not serve enough power
12V1-18A --> HDD/SATA?
12V2-18A --> 24Pin?
12V3-22A --> PCIe1?
12V4-22A --> PCIe2?
Anyone can help me, do you think this is right?
Maybe, then V1 rail definely won't be able to supply 2 board for long time. My kyoritsu clampmeter show about 9 A DC used by single HEX16C.
So you need to devided all three board on V1, V3, V4.
Good luck
Well, I tried both PCIe Ports and also CPU 4 Pin, but one board is still running at ~15GH.
In order to be sure, I tried the board alone, same situation as with all 3 boards.
I will try to get my hands on a second PSU, maybe it will help.
Thanks anyway
Marto, any clue?
Edit: I tried with an extra PSU (16A) just for this one board, same result
Clock and voltage please. Leave the board for at least 24 hours to minimize variance.
[...]
Marto whats going on!?? I waited longer then you told me and now the device even don't work?
GIVE ME INFORMATION!
2. Try it with windows first before you start to complain
3. Search in two god topic for precompiled binary which was reported to work
5 next time if you ask politely for help I am sure that a lot of us will help you but I will pass this time
Pi is totally stressed out with all 3 boards, not possible to get them up running.
On Ubuntu, I managed to get all 3 boards running, but after 8 hours, the PSU stopped, I guess it went in protection mode.
One board only ran with 15GH/s, so I guess it is not getting enough power and this caused that the PSU stopped.
Right now, this one board doesn't even start and shows 0 GH/s in cgminer.
My PSU (be quiet! Straight Power E9 700W ATX 2.31) has 4 rails, but which rail do I have to use?:
I think at the moment I do have two boards connected to HDD wire, which I guess do not serve enough power
12V1-18A --> HDD/SATA?
12V2-18A --> 24Pin?
12V3-22A --> PCIe1?
12V4-22A --> PCIe2?
Anyone can help me, do you think this is right?
Maybe, then V1 rail definely won't be able to supply 2 board for long time. My kyoritsu clampmeter show about 9 A DC used by single HEX16C.
So you need to devided all three board on V1, V3, V4.
Good luck
Well, I tried both PCIe Ports and also CPU 4 Pin, but one board is still running at ~15GH.
In order to be sure, I tried the board alone, same situation as with all 3 boards.
I will try to get my hands on a second PSU, maybe it will help.
Thanks anyway
Marto, any clue?
Edit: I tried with an extra PSU (16A) just for this one board, same result
hi,
i just compiled the patched cgminer on OSX.
when i check for found devices i get:
but for some reason after about 5 - 10 seconds the HEX16C dissapears:
whats the fault??
#EDIT:
i can't get it running. device fails to initialize!!!
i just compiled the patched cgminer on OSX.
when i check for found devices i get:
Code:
tr0ja-2:cgminer asicuser$ sudo ./cgminer -n
[2014-01-07 16:36:45] USB all: found 6 devices - listing known devices
.USB dev 0: Bus 250 Device 7 ID: 04d8:000a
Manufacturer: 'TECHNOBIT HEX ASIC Miner.'
Product: 'HEX16C-Avalon2 ASIC Miner'
[2014-01-07 16:36:45] 1 known USB devices
but for some reason after about 5 - 10 seconds the HEX16C dissapears:
Code:
tr0ja-2:cgminer asicuser$ sudo ./cgminer -n
[2014-01-07 16:39:31] USB all: found 5 devices - listing known devices
[2014-01-07 16:39:31] No known USB devices
whats the fault??
#EDIT:
i can't get it running. device fails to initialize!!!
i get no device detected can someone advise please, ubuntu running cgminer with hex build..
one day satoshi will return and demand licence fee from every greedy mofo on this forum...I'm sorry, did i read it wrong??
Are you complain cause no one answer your question?
I don't even complain when i answer someone question & get ignore by the person. Read this thread & see how many i get ignored.
What's up whit shipment ? Have somebody got emails from technobit?
get under SSH screen-r this error message
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
Try to fill in the : Hex16U Frequency (Default: 54) with 54.
If still error then change : Handle USB detect errors as (Default: hexA) to hexA
i get no device detected can someone advise please, ubuntu running cgminer with hex build..
one day satoshi will return and demand licence fee from every greedy mofo on this forum...
get under SSH screen-r this error message
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
http://itech-kredit.de/---/hex.jpg
have HEX16A2
mr-3020 with FW 0.1.3
can someone please help me?
Tue Jan 7 12:55:44 CET 2014: cgminer exited status (1)
Tue Jan 7 12:55:44 CET 2014: Sleeping for 10...
Tue Jan 7 12:55:54 CET 2014: Starting cgminer
[2014-01-07 12:55:54] Unexpected extra commandline arguments
http://itech-kredit.de/---/hex.jpg
Pi is totally stressed out with all 3 boards, not possible to get them up running.
On Ubuntu, I managed to get all 3 boards running, but after 8 hours, the PSU stopped, I guess it went in protection mode.
One board only ran with 15GH/s, so I guess it is not getting enough power and this caused that the PSU stopped.
Right now, this one board doesn't even start and shows 0 GH/s in cgminer.
My PSU (be quiet! Straight Power E9 700W ATX 2.31) has 4 rails, but which rail do I have to use?:
I think at the moment I do have two boards connected to HDD wire, which I guess do not serve enough power
12V1-18A --> HDD/SATA?
12V2-18A --> 24Pin?
12V3-22A --> PCIe1?
12V4-22A --> PCIe2?
Anyone can help me, do you think this is right?
Maybe, then V1 rail definely won't be able to supply 2 board for long time. My kyoritsu clampmeter show about 9 A DC used by single HEX16C.
So you need to devided all three board on V1, V3, V4.
Good luck
Jump to: