Topic: Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 36. (Read 104884 times)
How much power will one chip draw at maximum speed?
Try Hex Miner windows on a PC with just that board.
you can try to restart cgminer from cgminer setting over & over.
While testing cgminer 3.8.5 on my android tablet, my HEX16c not detected while other 2 HEX16A detected. Then restart cgminer, HEX16C detected as HEX16A. The restart again & HEX16C detected along with HEX16A.
Had you already try to switch the miner position & still encounter same problem? If the other miner dead then your miner is ok. Maybe problem with usb HUB.
Pi is totally stressed out with all 3 boards, not possible to get them up running.
On Ubuntu, I managed to get all 3 boards running, but after 8 hours, the PSU stopped, I guess it went in protection mode.
One board only ran with 15GH/s, so I guess it is not getting enough power and this caused that the PSU stopped.
Right now, this one board doesn't even start and shows 0 GH/s in cgminer.
My PSU (be quiet! Straight Power E9 700W ATX 2.31) has 4 rails, but which rail do I have to use?:
I think at the moment I do have two boards connected to HDD wire, which I guess do not serve enough power
12V1-18A --> HDD/SATA?
12V2-18A --> 24Pin?
12V3-22A --> PCIe1?
12V4-22A --> PCIe2?
Anyone can help me, do you think this is right?
Help i just changed my ip adress on the mr-3020 to dynamic, how do I find out what ip to connect to?
And: I paid BJJNEKBIM 2013-12-13 581,00€ Bank Wire Awaiting bank wire payment - on the 29th of november with the correct iban and my order code in the information. Have you still not recieved payment? This is why I hate bank wire... You should accept paypal again!
And: I paid BJJNEKBIM 2013-12-13 581,00€ Bank Wire Awaiting bank wire payment - on the 29th of november with the correct iban and my order code in the information. Have you still not recieved payment? This is why I hate bank wire... You should accept paypal again!
Just go to your other router menu & find statistic.
Help i just changed my ip adress on the mr-3020 to dynamic, how do I find out what ip to connect to?
And: I paid BJJNEKBIM 2013-12-13 581,00€ Bank Wire Awaiting bank wire payment - on the 29th of november with the correct iban and my order code in the information. Have you still not recieved payment? This is why I hate bank wire... You should accept paypal again!
And: I paid BJJNEKBIM 2013-12-13 581,00€ Bank Wire Awaiting bank wire payment - on the 29th of november with the correct iban and my order code in the information. Have you still not recieved payment? This is why I hate bank wire... You should accept paypal again!
i get no device detected can someone advise please, ubuntu running cgminer with hex build..
This doc should help you http://sven-goessling.de/14/12/2013/der-40ghs-hex16b-bitfury-asic-bitcoin-miner-auf-dem-raspberry-pi-14-12-13/
But use this settings: --hexminerc-voltage 1100 --hexminerc-options 16:1500
Ordered and Paid 12/7/2013 -- mine still just sits at "Payment Accepted" stage... no notice that it has shipped and no tracking #.
Order ref: LUMUYJIUW
Order ref: LUMUYJIUW
Well got a shipping email today but no tracking number as yet.
Hope this is not a way to just avoid refunding me
Will keep you all informed
Hope this is not a way to just avoid refunding me
Will keep you all informed
Well just as I thought. Still no tracking number so I will guess these have not been sent yet, and this is just away to avoid refund
The tracking info is in the order details on the Technobit site. For me I paid for UPS express but it shipped speedy. I can't track speedy to states. Dpd is horrible to states I just want it to show up with out major complications.
not for me i checked nothing in order detail except shipped
Lets see how it goes.
You can track multiple packages at the same time by separating the tracking numbers with a comma ( , ).
Tracking a package might take some time. Please wait for the page to load fully.
The “Track” button needs to only be clicked once.
Shipment number:
Shipment number: 60065545764
Date Operation Settlement
2014-01-06 13:10:27 Courier Pick-up SOFIA
* A delay in the shipment status update may be expected for international deliveries.
Well got a shipping email today but no tracking number as yet.
Hope this is not a way to just avoid refunding me
Will keep you all informed
Hope this is not a way to just avoid refunding me
Will keep you all informed
Well just as I thought. Still no tracking number so I will guess these have not been sent yet, and this is just away to avoid refund
The tracking info is in the order details on the Technobit site. For me I paid for UPS express but it shipped speedy. I can't track speedy to states. Dpd is horrible to states I just want it to show up with out major complications.
not for me i checked nothing in order detail except shipped
Well got a shipping email today but no tracking number as yet.
Hope this is not a way to just avoid refunding me
Will keep you all informed
Hope this is not a way to just avoid refunding me
Will keep you all informed
Well just as I thought. Still no tracking number so I will guess these have not been sent yet, and this is just away to avoid refund
The tracking info is in the order details on the Technobit site. For me I paid for UPS express but it shipped speedy. I can't track speedy to states. Dpd is horrible to states I just want it to show up with out major complications.
Well got a shipping email today but no tracking number as yet.
Hope this is not a way to just avoid refunding me
Will keep you all informed
Hope this is not a way to just avoid refunding me
Will keep you all informed
Well just as I thought. Still no tracking number so I will guess these have not been sent yet, and this is just away to avoid refund
i get no device detected can someone advise please, ubuntu running cgminer with hex build..
2 out of my 3 orders were shipped and received late december.
Now I'm just waiting for order OSPRSHZDH , order/pay date 28-11-2013, "shipment december"
Now I'm just waiting for order OSPRSHZDH , order/pay date 28-11-2013, "shipment december"
What I don't understand is why everybody uses the tl-mr3020. I have four bitburners running on a Pi and 10 red fury sticks running on another Pi. Is there a problem with using cgminer on a PI with these HEX16A2?
Thanks
Lars
The answer is because TL-MR3020 more cheaper than pi
I ordered the same but the Jan batch. Is the power connector part of the package?
What replacement fan would you recommend?
No, the power connector( Blue & black cable with EPS adapter) & blue heatsink is not part of the package. I made the power connector & buy the heatsink in EBAY
I am still looking for other fan that closed to SUNON performance. i will post if i find something that closed enough since i had air conditioner in room. That sunon really great, just too noisy for me to place it in my bed room
Try prepare what you need from now, so when the miner arrived you can start hashing.
PSU, the host ( PC or TPLINK TL-MR3020), usb cable.
That's what I am already trying to do: be prepared. Got my cables (easiest part) and I am a bit worried about connecting with wires and not molex.
As for fans. I think I strap a Noiseblocker 120mm XLP(http://www.blacknoise.com/en/products/it/17/Noiseblocker-NB_BlackSilentFan_120mm) on the heat sink. I did the same with my four bitburner. The XLP has up to 75cfm.
What I don't understand is why everybody uses the tl-mr3020. I have four bitburners running on a Pi and 10 red fury sticks running on another Pi. Is there a problem with using cgminer on a PI with these HEX16A2?
Thanks
Lars
What is the best OC settings everyone has tested.
--hexminerc-voltage 1100 --hexminerc-options 16:1500
Hi, I have a problem again with my boards.
I had one board up and running since Christmas mit terminal screw.
Now I have received 2 addtional boards with molex connector.
I connected them to my powerd usb hub and PSU with seperated rails with each 18A, so enough power.
Cgminer on raspberry pi freezes immediatly as soon as i try to start it.
On Ubuntu, i can only start 2 boards, the 3. one will be shown as OFF in cgminer.
I already tried different USB cables.
Is it possible that this one board is broken or does anyone have the same problem?
best regards
I had one board up and running since Christmas mit terminal screw.
Now I have received 2 addtional boards with molex connector.
I connected them to my powerd usb hub and PSU with seperated rails with each 18A, so enough power.
Cgminer on raspberry pi freezes immediatly as soon as i try to start it.
On Ubuntu, i can only start 2 boards, the 3. one will be shown as OFF in cgminer.
I already tried different USB cables.
Is it possible that this one board is broken or does anyone have the same problem?
best regards
you can try to restart cgminer from cgminer setting over & over.
While testing cgminer 3.8.5 on my android tablet, my HEX16c not detected while other 2 HEX16A detected. Then restart cgminer, HEX16C detected as HEX16A. The restart again & HEX16C detected along with HEX16A.
Had you already try to switch the miner position & still encounter same problem? If the other miner dead then your miner is ok. Maybe problem with usb HUB.
But you did NOT answer the question AGAIN!!!
Hey Marto,
If you could share slightly more information to set peoples mind at ease might be good and calm people down. We all understand delays, But maybe once ever couple working days you could come on here and post exactly what order date you have shipped between the last update and the time you make the post.
Something in the form of:
Hi postage update for the 4/01/2014
Posted all orders made on 1/12/2013
-------------------------------------
Hi postage update for the 7/01/2014
Posted all orders up to and including the 5/12/2013
----------------------------------------------------
Something like that small of an update will put a lot of people at ease. Most of your updates are very indecisive. If we have learnt anything from previous unmentioned companies indecisive is a very very bad thing for your reputation.
Thanks and we all hope to see your company improve through out the new year.
Tyler.
Sound like BFL Jody blog update
:0
Let's hope that aside I'm not a lady we are far away from BFL in terms of late shipments
We are spending our efforts on production shipping and testing.Hey Marto,
If you could share slightly more information to set peoples mind at ease might be good and calm people down. We all understand delays, But maybe once ever couple working days you could come on here and post exactly what order date you have shipped between the last update and the time you make the post.
Something in the form of:
Hi postage update for the 4/01/2014
Posted all orders made on 1/12/2013
-------------------------------------
Hi postage update for the 7/01/2014
Posted all orders up to and including the 5/12/2013
----------------------------------------------------
Something like that small of an update will put a lot of people at ease. Most of your updates are very indecisive. If we have learnt anything from previous unmentioned companies indecisive is a very very bad thing for your reputation.
Thanks and we all hope to see your company improve through out the new year.
Tyler.
Sound like BFL Jody blog update
Let's hope that aside I'm not a lady we are far away from BFL in terms of late shipments
Yesterday more than 10 TH of devices went out.
We did missed our goal to catch up until Christmas .
But We are very close now.
I''m not able to provide more detailed info @ the moment
Best Martin
thats all dandy but some compensation is needed for late deliveries.
What is the best OC settings everyone has tested.
Hi, I have a problem again with my boards.
I had one board up and running since Christmas mit terminal screw.
Now I have received 2 addtional boards with molex connector.
I connected them to my powerd usb hub and PSU with seperated rails with each 18A, so enough power.
Cgminer on raspberry pi freezes immediatly as soon as i try to start it.
On Ubuntu, i can only start 2 boards, the 3. one will be shown as OFF in cgminer.
I already tried different USB cables.
Is it possible that this one board is broken or does anyone have the same problem?
best regards
I had one board up and running since Christmas mit terminal screw.
Now I have received 2 addtional boards with molex connector.
I connected them to my powerd usb hub and PSU with seperated rails with each 18A, so enough power.
Cgminer on raspberry pi freezes immediatly as soon as i try to start it.
On Ubuntu, i can only start 2 boards, the 3. one will be shown as OFF in cgminer.
I already tried different USB cables.
Is it possible that this one board is broken or does anyone have the same problem?
best regards
Try Hex Miner windows on a PC with just that board.
Hi, I have a problem again with my boards.
I had one board up and running since Christmas mit terminal screw.
Now I have received 2 addtional boards with molex connector.
I connected them to my powerd usb hub and PSU with seperated rails with each 18A, so enough power.
Cgminer on raspberry pi freezes immediatly as soon as i try to start it.
On Ubuntu, i can only start 2 boards, the 3. one will be shown as OFF in cgminer.
I already tried different USB cables.
Is it possible that this one board is broken or does anyone have the same problem?
best regards
I had one board up and running since Christmas mit terminal screw.
Now I have received 2 addtional boards with molex connector.
I connected them to my powerd usb hub and PSU with seperated rails with each 18A, so enough power.
Cgminer on raspberry pi freezes immediatly as soon as i try to start it.
On Ubuntu, i can only start 2 boards, the 3. one will be shown as OFF in cgminer.
I already tried different USB cables.
Is it possible that this one board is broken or does anyone have the same problem?
best regards
Jump to: