SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching - page 13.

Topcd

newbie

Activity: 7

Merit: 0

Quote from: KhorneFlake on June 25, 2019, 08:04:32 AM

Hey, thx for the reply. I didn't OC, just undervolted, and even downclocked the core to lower the temps. Worked fine so far, till I installed the 1.9.0.

Also, it seems I cannot send you any messages. You can post here your OverdriveN settings, that's why this forum is for, anyways.

You can PM me now,
It was disabled by default to receive messages from other members!
What is your exact card's model? Rx Vega 64 Reference model?
Because the numbers changes card by card.

KhorneFlake

newbie

Activity: 27

Merit: 0

Hey, thx for the reply. I didn't OC, just undervolted, and even downclocked the core to lower the temps. Worked fine so far, till I installed the 1.9.0.

Also, it seems I cannot send you any messages. You can post here your OverdriveN settings, that's why this forum is for, anyways.

Topcd

newbie

Activity: 7

Merit: 0

Quote from: KhorneFlake on June 24, 2019, 08:05:38 AM

I'm already using that driver, and I always DDU before installing a new one.

Hey man
Your temperature is badly high and is dangerous for this type of card
Once i had a problem with cooling for couple of days so the temperature of my Vegas raised up to 65 degrees and more
I got many errors in SRB such as BUS ID COMPUTE Error, Low Difficulty Share and etc.
But with 50 and lower degrees there is not even 1 error.
Try to increase FAN RPM to 3300 and more
Also your overclock option is not good
Send me a PM, i will give you my numbers to use with OverdriveNtool
Bad overclocking causes high power usage, high temperature and will damage your cards
Try to use 18.6.1 Adrenalin driver, i think its the best compatible version with SRBMINER
Just try to keep them cool.
Here are my results without TWEAKING
https://imgur.com/a/mnYohLR

KhorneFlake

newbie

Activity: 27

Merit: 0

I'm already using that driver, and I always DDU before installing a new one.

doktor83

hero member

Activity: 2548

Merit: 626

Quote from: KhorneFlake on June 24, 2019, 12:31:20 AM

Doesn't seem to be helping, unless I did something wrong.

Hard to tell what's causing it..
Something you could always try is to delete video drivers with DDU and then reinstall them. Also 18.6.1 are recommended.

KhorneFlake

newbie

Activity: 27

Merit: 0

Doesn't seem to be helping, unless I did something wrong.

doktor83

hero member

Activity: 2548

Merit: 626

Quote from: KhorneFlake on June 23, 2019, 06:11:40 AM

Yo, I'm back. A couple of days ago I finished mining another monero with my two 64s. I was on the 1.8.0 but had to update because I didn't mine anything afterwards. So, I'm at 1.9.0 now, and my main GPU never goes to its full potential. Always starts around 1000h/s and just drops and drops over time. Sure, that happened before If I was using anything besides the miner, but now its the case even after fresh restart, and nothing besides the miner is active. Can someone help, or if its a bug could you look at it?

Try adding --nobinaries parameter to start.bat , maybe your cards have a problem with the built in binaries.

KhorneFlake

newbie

Activity: 27

Merit: 0

Yo, I'm back. A couple of days ago I finished mining another monero with my two 64s. I was on the 1.8.0 but had to update because I didn't mine anything afterwards. So, I'm at 1.9.0 now, and my main GPU never goes to its full potential. Always starts around 1000h/s and just drops and drops over time. Sure, that happened before If I was using anything besides the miner, but now its the case even after fresh restart, and nothing besides the miner is active. Can someone help, or if its a bug could you look at it?

Edit: and now this happened

https://i.imgur.com/Cldv0yT.png

rainbowminer

jr. member

Activity: 95

Merit: 2

Quote from: doktor83 on June 22, 2019, 01:36:32 PM

Quote from: rainbowminer on June 22, 2019, 08:16:05 AM

Hello doktor83,

what is the characteristic of the ramp-up curve, when using --enablegpurampup ? Is it linear, and, how long does it take unil it reaches the maximum?

Thank you for your reply in forward,

RBM

Every thread is delayed 2 seconds. So if you have 6 gpu, every gpu is running 2 threads, that is 12 threads total so ~ 24 seconds until every gpu starts working.
Except on CN/R, because of the precompilation process. Until precompilation is finished, the gpu is idling.

Super! Thank you very much for the reply.

doktor83

hero member

Activity: 2548

Merit: 626

Quote from: rainbowminer on June 22, 2019, 08:16:05 AM

Hello doktor83,

what is the characteristic of the ramp-up curve, when using --enablegpurampup ? Is it linear, and, how long does it take unil it reaches the maximum?

Thank you for your reply in forward,

RBM

Every thread is delayed 2 seconds. So if you have 6 gpu, every gpu is running 2 threads, that is 12 threads total so ~ 24 seconds until every gpu starts working.
Except on CN/R, because of the precompilation process. Until precompilation is finished, the gpu is idling.

rainbowminer

jr. member

Activity: 95

Merit: 2

Hello doktor83,

what is the characteristic of the ramp-up curve, when using --enablegpurampup ? Is it linear, and, how long does it take unil it reaches the maximum?

Thank you for your reply in forward,

RBM

doktor83

hero member

Activity: 2548

Merit: 626

Quote from: raptorman on June 21, 2019, 05:27:09 PM

Quote from: doktor83 on June 21, 2019, 10:23:40 AM

Quote from: raptorman on June 21, 2019, 10:10:27 AM

Hello Doctor83,

With 1.8.9 the rigs stops after 10-12 hours, and the 1.9.0 make to many compute errors any algorithm with vega 64 cards. The 1.8.8 was works fine. Please check what was the problem.

Cheers.

From 1.8.9 to 1.9.0 nothing changed in kernels, so i don't see a reason for more compute errors.
Can you give more info, a log would be the most helpful i can see almost everything from it.

Maybe you have problems with the embedded binaries (but i dont see any reason why would it cause problems).
You can add --nobinaries in start.bat so they won't be used, try it.

Thanks doctor, now works fine!

Great, but nevertheless, can you send me a log ?

raptorman

newbie

Activity: 24

Merit: 0

Quote from: doktor83 on June 21, 2019, 10:23:40 AM

Quote from: raptorman on June 21, 2019, 10:10:27 AM

Hello Doctor83,

With 1.8.9 the rigs stops after 10-12 hours, and the 1.9.0 make to many compute errors any algorithm with vega 64 cards. The 1.8.8 was works fine. Please check what was the problem.

Cheers.

From 1.8.9 to 1.9.0 nothing changed in kernels, so i don't see a reason for more compute errors.
Can you give more info, a log would be the most helpful i can see almost everything from it.

Maybe you have problems with the embedded binaries (but i dont see any reason why would it cause problems).
You can add --nobinaries in start.bat so they won't be used, try it.

Thanks doctor, now works fine!

doktor83

hero member

Activity: 2548

Merit: 626

Quote from: raptorman on June 21, 2019, 10:10:27 AM

Hello Doctor83,

With 1.8.9 the rigs stops after 10-12 hours, and the 1.9.0 make to many compute errors any algorithm with vega 64 cards. The 1.8.8 was works fine. Please check what was the problem.

Cheers.

From 1.8.9 to 1.9.0 nothing changed in kernels, so i don't see a reason for more compute errors.
Can you give more info, a log would be the most helpful i can see almost everything from it.

Maybe you have problems with the embedded binaries (but i dont see any reason why would it cause problems).
You can add --nobinaries in start.bat so they won't be used, try it.

raptorman

newbie

Activity: 24

Merit: 0

Hello Doctor83,

With 1.8.9 the rigs stops after 10-12 hours, and the 1.9.0 make to many compute errors any algorithm with vega 64 cards. The 1.8.8 was works fine. Please check what was the problem.

Cheers.

livada

newbie

Activity: 417

Merit: 0

Quote from: dingdongtobias on June 21, 2019, 07:28:17 AM

Quote from: livada on June 21, 2019, 06:40:12 AM

Quote from: kibatronic on June 21, 2019, 04:36:19 AM

Quote from: dingdongtobias on June 20, 2019, 11:49:39 PM

Quote from: kibatronic on June 20, 2019, 05:55:44 PM

Quote from: dingdongtobias on June 20, 2019, 08:21:56 AM

Quote from: MATHReX on June 20, 2019, 04:32:06 AM

Quote from: issie81 on June 12, 2019, 10:05:01 AM

I am not even coming close to 10:)) 4 for doable it seems alot of rigs running 4 pretty much stable since i remote control the miners by awesome miner maybe a simple reboot Will do the fix

What is the power consumption for the Vega rig? How much is one GPU consuming through the wall?
My 6x VEGA 56 Rig is doing 12000 H/s (v4 monero) with 1500W from the wall.
Isn't it much? In the previous algo it used to consume 1250-1300W from the wall for the same hashrate.

too much

5 x vega56 SRB 1.8.9 tweak profile 9 and 10 = ~ 1030w from wall and 10500 hs (1450/930 875mv)

Still too much. ;-)

4x watercooled Vega 56 with Vega 64 BIOS, 1401/975MHz 810-820mV in ODNT, ~8200Hs pulling 650W from the wall:

https://i.ibb.co/z8Lwrs7/Quad-Vega56-XMR.png

vega56 wit 64 bios use ~ 120w? yea right...

They are pulling about 135-140W each (from the wall). I don't know where you got 120W from?

he to smart but not read your post

or have 6 years and not learn * and / in matematic

btw. nice score - 12,6HR/wat is good. samsung rules- hynix bad

yes you very smart and know how much that rig use W in idle ?
of course you not know

i take assume idle rig use 150w but your rig only 4 gpu so less. 150-180w idle 8xvega rig

140w nice also very

go read again post.
he say 8200hr - he say 4 vega - he say 650W
he dont have 8 vega card- just READ.
140W per car dis normal for TRM
my 6 vega in IDLE use only 85/100W. and rig have 6 extra fan.
your rig use 150W in IDLE? you must reinstal all and instal again. this is to much for idle.

CNR-6 vega 56 stock - 980/1000W - 100W idle - 900/6=150W card etc...

dingdongtobias

newbie

Activity: 156

Merit: 0

Quote from: livada on June 21, 2019, 06:40:12 AM

Quote from: kibatronic on June 21, 2019, 04:36:19 AM

Quote from: dingdongtobias on June 20, 2019, 11:49:39 PM

Quote from: kibatronic on June 20, 2019, 05:55:44 PM

Quote from: dingdongtobias on June 20, 2019, 08:21:56 AM

Quote from: MATHReX on June 20, 2019, 04:32:06 AM

Quote from: issie81 on June 12, 2019, 10:05:01 AM

I am not even coming close to 10:)) 4 for doable it seems alot of rigs running 4 pretty much stable since i remote control the miners by awesome miner maybe a simple reboot Will do the fix

What is the power consumption for the Vega rig? How much is one GPU consuming through the wall?
My 6x VEGA 56 Rig is doing 12000 H/s (v4 monero) with 1500W from the wall.
Isn't it much? In the previous algo it used to consume 1250-1300W from the wall for the same hashrate.

too much

5 x vega56 SRB 1.8.9 tweak profile 9 and 10 = ~ 1030w from wall and 10500 hs (1450/930 875mv)

Still too much. ;-)

4x watercooled Vega 56 with Vega 64 BIOS, 1401/975MHz 810-820mV in ODNT, ~8200Hs pulling 650W from the wall:

https://i.ibb.co/z8Lwrs7/Quad-Vega56-XMR.png

vega56 wit 64 bios use ~ 120w? yea right...

They are pulling about 135-140W each (from the wall). I don't know where you got 120W from?

he to smart but not read your post

or have 6 years and not learn * and / in matematic

btw. nice score - 12,6HR/wat is good. samsung rules- hynix bad

yes you very smart and know how much that rig use W in idle ?
of course you not know

i take assume idle rig use 150w but your rig only 4 gpu so less. 150-180w idle 8xvega rig

140w nice also very

livada

newbie

Activity: 417

Merit: 0

Quote from: kibatronic on June 21, 2019, 04:36:19 AM

Quote from: dingdongtobias on June 20, 2019, 11:49:39 PM

Quote from: kibatronic on June 20, 2019, 05:55:44 PM

Quote from: dingdongtobias on June 20, 2019, 08:21:56 AM

Quote from: MATHReX on June 20, 2019, 04:32:06 AM

Quote from: issie81 on June 12, 2019, 10:05:01 AM

I am not even coming close to 10:)) 4 for doable it seems alot of rigs running 4 pretty much stable since i remote control the miners by awesome miner maybe a simple reboot Will do the fix

What is the power consumption for the Vega rig? How much is one GPU consuming through the wall?
My 6x VEGA 56 Rig is doing 12000 H/s (v4 monero) with 1500W from the wall.
Isn't it much? In the previous algo it used to consume 1250-1300W from the wall for the same hashrate.

too much

5 x vega56 SRB 1.8.9 tweak profile 9 and 10 = ~ 1030w from wall and 10500 hs (1450/930 875mv)

Still too much. ;-)

4x watercooled Vega 56 with Vega 64 BIOS, 1401/975MHz 810-820mV in ODNT, ~8200Hs pulling 650W from the wall:

https://i.ibb.co/z8Lwrs7/Quad-Vega56-XMR.png

vega56 wit 64 bios use ~ 120w? yea right...

They are pulling about 135-140W each (from the wall). I don't know where you got 120W from?

he to smart but not read your post

or have 6 years and not learn * and / in matematic

btw. nice score - 12,6HR/wat is good. samsung rules- hynix bad

kibatronic

newbie

Activity: 22

Merit: 1

Quote from: dingdongtobias on June 20, 2019, 11:49:39 PM

Quote from: kibatronic on June 20, 2019, 05:55:44 PM

Quote from: dingdongtobias on June 20, 2019, 08:21:56 AM

Quote from: MATHReX on June 20, 2019, 04:32:06 AM

Quote from: issie81 on June 12, 2019, 10:05:01 AM

I am not even coming close to 10:)) 4 for doable it seems alot of rigs running 4 pretty much stable since i remote control the miners by awesome miner maybe a simple reboot Will do the fix

What is the power consumption for the Vega rig? How much is one GPU consuming through the wall?
My 6x VEGA 56 Rig is doing 12000 H/s (v4 monero) with 1500W from the wall.
Isn't it much? In the previous algo it used to consume 1250-1300W from the wall for the same hashrate.

too much

5 x vega56 SRB 1.8.9 tweak profile 9 and 10 = ~ 1030w from wall and 10500 hs (1450/930 875mv)

Still too much. ;-)

4x watercooled Vega 56 with Vega 64 BIOS, 1401/975MHz 810-820mV in ODNT, ~8200Hs pulling 650W from the wall:

https://i.ibb.co/z8Lwrs7/Quad-Vega56-XMR.png

vega56 wit 64 bios use ~ 120w? yea right...

They are pulling about 135-140W each (from the wall). I don't know where you got 120W from?

dingdongtobias

newbie

Activity: 156

Merit: 0

Quote from: kibatronic on June 20, 2019, 05:55:44 PM

Quote from: dingdongtobias on June 20, 2019, 08:21:56 AM

Quote from: MATHReX on June 20, 2019, 04:32:06 AM

Quote from: issie81 on June 12, 2019, 10:05:01 AM

I am not even coming close to 10:)) 4 for doable it seems alot of rigs running 4 pretty much stable since i remote control the miners by awesome miner maybe a simple reboot Will do the fix

What is the power consumption for the Vega rig? How much is one GPU consuming through the wall?
My 6x VEGA 56 Rig is doing 12000 H/s (v4 monero) with 1500W from the wall.
Isn't it much? In the previous algo it used to consume 1250-1300W from the wall for the same hashrate.

too much

5 x vega56 SRB 1.8.9 tweak profile 9 and 10 = ~ 1030w from wall and 10500 hs (1450/930 875mv)

Still too much. ;-)

4x watercooled Vega 56 with Vega 64 BIOS, 1401/975MHz 810-820mV in ODNT, ~8200Hs pulling 650W from the wall:

https://i.ibb.co/z8Lwrs7/Quad-Vega56-XMR.png

vega56 wit 64 bios use ~ 120w? yea right...

Topic: SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching - page 13. (Read 237261 times)