New amd drivers 19.9.1 have sorted Navi mining issues
54mhs on Eth at 105w
Topic: SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching - page 2. (Read 237260 times)
September 05, 2019, 05:05:22 AM
September 02, 2019, 09:06:13 PM
Hi All,
I have a dilemma:
My Mining is constantly interrupted by too many compute errors. The miner still runs and consumes electricity but no valid shares are submitted. This is frustrating and very unprofittable.
I have read about lowering memory clocks and upping voltage but this happens with stock settings as well. Using 5x580 rig and 1x vega 56 + 1x580 configuration. Both setups run into same problem every few hours or so.
What can be done?
Is there a setting in the miner that it restarts once too many compute errors are shown? If not, why not?
I found the setting for adjusting when to display the error message but not how to restart based on this error.
Someone please help.
PS. Setting restart based on hashing speed drop or too many invalid shares does not help, hashes stay up and no invalid share but nothing is accepted on pool-side, only red too many compute error messages in srbminer.
Many thanks,
doctor0c, grandson of doktor83
I have a dilemma:
My Mining is constantly interrupted by too many compute errors. The miner still runs and consumes electricity but no valid shares are submitted. This is frustrating and very unprofittable.
I have read about lowering memory clocks and upping voltage but this happens with stock settings as well. Using 5x580 rig and 1x vega 56 + 1x580 configuration. Both setups run into same problem every few hours or so.
What can be done?
Is there a setting in the miner that it restarts once too many compute errors are shown? If not, why not?
I found the setting for adjusting when to display the error message but not how to restart based on this error.
Someone please help.
PS. Setting restart based on hashing speed drop or too many invalid shares does not help, hashes stay up and no invalid share but nothing is accepted on pool-side, only red too many compute error messages in srbminer.
Many thanks,
doctor0c, grandson of doktor83
August 30, 2019, 06:16:42 PM
The achieved values are currently between: 2300 - 2350 H/s per card @tweak-profile "10"
Total power consumption at: ~ 2410 watts (/ 12 = 200.83 watts per card)
wow! this is really great! Thanks for settings. I had 17200 for 8 liquid cards, these settings give 18 650 and a little bit lower power consumption.Total power consumption at: ~ 2410 watts (/ 12 = 200.83 watts per card)
Did anybody manage to get good hashes on Micron memory? I have ~1800 on MSI Air Vega 56 with SRB. TRM gives more, but it often stucks with no reaction.
August 29, 2019, 06:23:09 AM
Hi! Help register a delayed start at 30 after loading and restart the miner every 3 hours! Please!
August 27, 2019, 02:54:21 PM
will you ad Cryptonight-zum-lite?
Yes, just need a few days to get some free time.
August 27, 2019, 08:28:50 AM
will you ad Cryptonight-zum-lite?
August 26, 2019, 04:23:54 AM
Does the miner work with mobile AM GPUs? like WX 4100/7100 or AMD Pro?
Just tried it. it is working. giving 305Hs/and 475Hs.
August 26, 2019, 04:10:09 AM
Does the miner work with mobile AM GPUs? like WX 4100/7100 or AMD Pro?
August 22, 2019, 08:12:11 AM
CONCEAL - CCX - COMPARE
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
great, i see your temperature is so low, how to keep this low temperature, what is your environment temperature? what vega 56 do you have?
flashing 64 increase the memory voltage, i am curious how it keep such low temperature, it is impressive!!!!!
only power. more power more temp. use PPT table and 860mv for gpu and meme and this is it.
1 card is vega 64LE(water cooling) and this gpu have only 49° .
vega 56@64bios- 55-57° is normal with 860-870mv gpu and mem.
vega56 ref- fan work 2500-3500rpm
vega 56 nitro -fan work 1200-2500rpm (50-56°)
the room temperature is 25-35°
excellent, for the card vega 56 nitro limited edition with hynix memory which have 3 8pin, is it possible to flash 64 or is it need to flash 64 to reach higher hashrate? this card need at least 905mv, lower it will crash or got a lot of errors, rubbish card...
[2019-08-22 20:26:47] Stats Uptime: 1 days, 04:31:00
[2019-08-22 20:26:47] GPU 0 [60C, fan 64%] cnr: 2.094kh/s, avg 2.093kh/s, pool 1.994kh/s a:1084 r:0 hw:2
hynix memory
GPU 0 14*14:AAA
1448 900mv 938 905mv
timing:--i 0 --REF 12800 --RFC 168 --RCDRD 20 --RCDWR 8
can you help to improve it
my hynix on midle setings have 2060hr etc- 1360/840mv and 919/860mv - 14*14:BAB (temp 53°- fan 1500rpm)
WinAMDTweak.exe --RAS 24 --rp 14 --rc 35 --rfc 168 --rrds 4 --rrdl 5 --rcdrd 19 --rcdwr 7 --REF 15600
hynix on HIGH seting have +2100hr etc - 1440/870mv and 929/872mv etc(temp +56° - fan +2000rpm)
vega56nitro(hynix) not work good with vega 64 bios- i try- only use more power
this is SRB topic and you talk only for TRM miner. Go in TRM topic.
August 22, 2019, 07:33:29 AM
CONCEAL - CCX - COMPARE
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
great, i see your temperature is so low, how to keep this low temperature, what is your environment temperature? what vega 56 do you have?
flashing 64 increase the memory voltage, i am curious how it keep such low temperature, it is impressive!!!!!
only power. more power more temp. use PPT table and 860mv for gpu and meme and this is it.
1 card is vega 64LE(water cooling) and this gpu have only 49° .
vega 56@64bios- 55-57° is normal with 860-870mv gpu and mem.
vega56 ref- fan work 2500-3500rpm
vega 56 nitro -fan work 1200-2500rpm (50-56°)
the room temperature is 25-35°
excellent, for the card vega 56 nitro limited edition with hynix memory which have 3 8pin, is it possible to flash 64 or is it need to flash 64 to reach higher hashrate? this card need at least 905mv, lower it will crash or got a lot of errors, rubbish card...
[2019-08-22 20:26:47] Stats Uptime: 1 days, 04:31:00
[2019-08-22 20:26:47] GPU 0 [60C, fan 64%] cnr: 2.094kh/s, avg 2.093kh/s, pool 1.994kh/s a:1084 r:0 hw:2
hynix memory
GPU 0 14*14:AAA
1448 900mv 938 905mv
timing:--i 0 --REF 12800 --RFC 168 --RCDRD 20 --RCDWR 8
can you help to improve it
August 22, 2019, 05:47:34 AM
CONCEAL - CCX - COMPARE
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
great, i see your temperature is so low, how to keep this low temperature, what is your environment temperature? what vega 56 do you have?
flashing 64 increase the memory voltage, i am curious how it keep such low temperature, it is impressive!!!!!
only power. more power more temp. use PPT table and 860mv for gpu and meme and this is it.
1 card is vega 64LE(water cooling) and this gpu have only 49° .
vega 56@64bios- 55-57° is normal with 860-870mv gpu and mem.
vega56 ref- fan work 2500-3500rpm
vega 56 nitro -fan work 1200-2500rpm (50-56°)
the room temperature is 25-35°
August 21, 2019, 09:56:04 PM
CONCEAL - CCX - COMPARE
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
great, i see your temperature is so low, how to keep this low temperature, what is your environment temperature? what vega 56 do you have?
flashing 64 increase the memory voltage, i am curious how it keep such low temperature, it is impressive!!!!!
August 19, 2019, 06:15:27 AM
Hi KolordZ!
Here you have the link to RegFile for the ~ 2450 H / s settings.
https://drive.google.com/file/d/1gtrEwS8fEDJyUUvDncKRTsjqv6hTyoxN/view?usp=sharing
You just have to change the settings for P7 and P3 to the values of my link.
1690Mhz / 1000mV and 1100Mhz / 923mV
About VirtualMemory:
I've set 100,000 - 100,000 on my rig. With 12 graphics cards. I had previously 70,000 - 70,000, but this attitude was very close and could not open programs at full capacity.
So I would recommend healthy to set 10,000 memory / card.
Hope I could maybe help you.
Best regards
Patrick
Hi Patrick,
It doesn't work with this settings. My cards got 0 H/s then I got freeze. When I use Stock PowerTable and only change the setting for P7 and P3 it work ! But probably not really stable.. Could you help me to find the right value to get the best H/s without looking the electricity cost ?
I have try to set 10.000 memory/card but nothing change. I can run SRB with Tweak 10, it mine, but if I close the miner and restart it I have this error message... I don't understand why..
Thanks,
August 19, 2019, 04:40:42 AM
might want to remove from srb
Stellite - torque - scala Triple rebrand.
And it's forked to a CPU only algo defyx
Stellite - torque - scala Triple rebrand.
And it's forked to a CPU only algo defyx
August 16, 2019, 08:50:30 AM
I have already written a post where the cards to ~2450 H/s create, but was not paid attention to the power consumption!
I've been trying to achieve maximum performance here.
Here are the settings:
Topic SRB high performance: (without thinking about power consumption)
https://drive.google.com/file/d/1AiuqbS6gbPW6IsT7p8QmgB6GrfIphHzB/view?usp=sharing
OverdrivnTool-Values:
https://drive.google.com/file/d/1ydngQu040cwMsyW8gdJVLLJI52gH8fIj/view?usp=sharing
You can still try between: 1680Mhz/1000 or 1690Mhz/1000.
I am at your disposal for questions.
greetings
Patrick
Hi Patrick,
Coul you share the PowerTable-RegFile for this config please ?
https://drive.google.com/open?id=1E0W1XSJ0ktY61I35wBWLL1KO6FqZ6PdW
If you get a "Error CL_MEM_OBJECT_ALLOCATION_FAILURE" try increase virtual memory in windows.
Go with number of GPU's * 8gb + 8 , for example 6gpu * 8gb + 8 = 56gb virtual memory.
I have try to increase virtual memory in Windows as you say.
But nothing change, the error is always here..
What can I do now ? What do you need ?
Hello @doktor83,
Something new about this problem ?
Thanks !
Hi KolordZ!
Here you have the link to RegFile for the ~ 2450 H / s settings.
https://drive.google.com/file/d/1gtrEwS8fEDJyUUvDncKRTsjqv6hTyoxN/view?usp=sharing
You just have to change the settings for P7 and P3 to the values of my link.
1690Mhz / 1000mV and 1100Mhz / 923mV
About VirtualMemory:
I've set 100,000 - 100,000 on my rig. With 12 graphics cards. I had previously 70,000 - 70,000, but this attitude was very close and could not open programs at full capacity.
So I would recommend healthy to set 10,000 memory / card.
Hope I could maybe help you.
Best regards
Patrick
August 16, 2019, 02:28:43 AM
I have already written a post where the cards to ~2450 H/s create, but was not paid attention to the power consumption!
I've been trying to achieve maximum performance here.
Here are the settings:
Topic SRB high performance: (without thinking about power consumption)
https://drive.google.com/file/d/1AiuqbS6gbPW6IsT7p8QmgB6GrfIphHzB/view?usp=sharing
OverdrivnTool-Values:
https://drive.google.com/file/d/1ydngQu040cwMsyW8gdJVLLJI52gH8fIj/view?usp=sharing
You can still try between: 1680Mhz/1000 or 1690Mhz/1000.
I am at your disposal for questions.
greetings
Patrick
Hi Patrick,
Coul you share the PowerTable-RegFile for this config please ?
https://drive.google.com/open?id=1E0W1XSJ0ktY61I35wBWLL1KO6FqZ6PdW
If you get a "Error CL_MEM_OBJECT_ALLOCATION_FAILURE" try increase virtual memory in windows.
Go with number of GPU's * 8gb + 8 , for example 6gpu * 8gb + 8 = 56gb virtual memory.
I have try to increase virtual memory in Windows as you say.
But nothing change, the error is always here..
What can I do now ? What do you need ?
Hello @doktor83,
Something new about this problem ?
Thanks !
August 13, 2019, 03:49:31 AM
CONCEAL - CCX - COMPARE
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
2*vega56+1vega64
identical setup and amd mem tweak.
srbminer tweak is disable
SRBMINER- 12740HR (595W)
http://imgbox.com/D8LxVHDa
vega56-4200hr
vega64-4400hr
TRM - 13560HR (602W)
http://imgbox.com/HbjsmnsO
vega56-4400hr
vega64-4740hr
Dude i registered myself ..blah,blah,blah... i will not change miner.
Hi DOKTOR. you chg your IP?
we'll just see that. After fulfilling the DOKTOR wish for everyone to switch from v8 algo to new algo(RX), the doctor is free to close his miner as planned. The SRB miner only supports CN algo, which will all be unprofitable for mining with GPU after the implementation of the RX algorithm. TRM have identical problem, but TRM at least supports other algorithms, not just CN.
Agree with you !
me too.i like to use a miner that gives less and consumes more electricity like SRBMINER because i'm very smart
And about your earlier messages on last pages - you really do need to see a doctor, but not the one in this thread.
you meant a message like this?
I am ignoring this guy because he is just a plain dickhead,
I knew there will be some reaction on my message, and as im in good mood right now, so i unignored that fool.
I aint gonna fight with you cause you are an idiot, and it is like when you die, you don't know you are dead but for others around you it is hard. The same goes when you are an idiot, you don't know about it but it's hard for everyone around you.
I aint gonna fight with you cause you are an idiot, and it is like when you die, you don't know you are dead but for others around you it is hard. The same goes when you are an idiot, you don't know about it but it's hard for everyone around you.
Also just continuing making idiot of yourself.
This is like talking with a 12 yr old kid. (but in reality it is talking with a 50 yr old retarded guy)
yes you are right, hope your wishes come true. sorry gotta go now your birthgiver called and needs some help
And yes, you are a retarded idiot dickhead.
I don't have nice words for people like you.
I don't have nice words for people like you.
just like your shitposts
i know you will continue sending your shit, i have no doubt. So nothing new here. You are still boring.
After a post like this, REAL DOCTORS can't help it
Could be the best miner ever, the reason i dont change it is because of you, a desperate guy that need go to other threads advertise it.. mining is a big comunity, here we have space for all kind of miners softwares, and OS. like i said i just feel pity of you, you are sad.
August 13, 2019, 02:25:29 AM
Hey, how do i run a specific gpu alone or how do i disable certain gpus at command line?
--cgpuid is what you need
using --cgpuid 5 still runs all my cards (0-5).try it with other parameters, like this:
Code:
SRBMiner-CN.exe --ccryptonighttype normalv4 --cgpuid 5 --cgpuintensity 112 --cgpuworksize 16 --cgputhreads 2 --cpool xmr-eu1.nanopool.org:14444 --cwallet 4A5hJyu2FvuM2azexYssHW2odrNCNWVqLLmzCowrA57xGJLNufXfzVgcMpAy3YWpzZSAPALhVH4Ed7xo6RZYyw2bUtbm12g.donation
August 13, 2019, 01:48:36 AM
Hey, how do i run a specific gpu alone or how do i disable certain gpus at command line?
--cgpuid is what you need
using --cgpuid 5 still runs all my cards (0-5). August 13, 2019, 12:06:43 AM
Hey, how do i run a specific gpu alone or how do i disable certain gpus at command line?
--cgpuid is what you need
Jump to: