Hi all,
When placing coolers on a HEX4M chips anything special to mind to? Or is it just the same as placing cooler on CPU?
Asking because in few days a new hex4m without coolers will arrive.
I've got standard cooling paste here, do i need special cooling paste, e.g. with extra silver in it, or can i use cooling pads instead of cooling paste?
Wilco
Topic: TECHNOBIT support tread + customer feedback - page 12. (Read 62630 times)
Update: Since yesterday my miners have a performance increase of about 200 to 300 GHs. Thanks.
zdiag cant recognized it..it looks like i didnt plugged it at all..:/ can u check it in a two hours via teamw,when I come home?
whats minimal requirements for psu?wats and amps?
whats minimal requirements for psu?wats and amps?
you can't install drivers if the boards are not seen by windows though 
No
You just need drivers under windows.
Zdiag
and then cgminer compiled for windows
Give us teamViewer and We'll help
You just need drivers under windows.
Zdiag
and then cgminer compiled for windows
Give us teamViewer and We'll help
tried on two comp,with two usb cables...but without hub,as it is in tutorial,boards can connect directly to pc without tp link or hubs...and when I try that pc doesnt recognize usb at all :S the only possible thing is that the boards are not wotking..am I right?
HI,
clearly there is no USB connection.
If they tried 2 boards for sure have to check USB ->hub->tp-link or PC
clearly there is no USB connection.
If they tried 2 boards for sure have to check USB ->hub->tp-link or PC
he's getting fans spinning but no leds at all he's tried 2 boards and 2 psu's
check this
disconect everything.
1.Conect 12V PCI-e
2start the PSU (PSU fan running)
it should blink the red led near the MCU(pic)
3. Connect USB to PC or TP link after 2-3 sec it should light the green near MCU ( indicates USB is present)
disconect everything.
1.Conect 12V PCI-e
2start the PSU (PSU fan running)
it should blink the red led near the MCU(pic)
3. Connect USB to PC or TP link after 2-3 sec it should light the green near MCU ( indicates USB is present)
Cheers will try. But. He's getting no leds at all
whats the minimum amps for the minion boards to get them to run
Could try this with 4 minions enabled:
1 HEX4M:
400 MHz
660 mV
170 GH/s
170 W
12V, 14.5A
They can disable a chip or two with chip mask i.e. 7 or 3
18 AMP is roughly 200W
So use mask 3 @ 930/780 this will be in this range
18 AMP is roughly 200W
So use mask 3 @ 930/780 this will be in this range
Was trying to help someone but they only have 18amp on the 12v rails
Hi,
We'll be able to measure this tomorrow and report back here
Regards: Vesi
We'll be able to measure this tomorrow and report back here
Regards: Vesi
whats the minimum amps for the minion boards to get them to run
Wow, 8 line power supply. Some how i feel that 0,6 W/Gh just a dream
I've talked with Marto about the efficiency of power regulators, these blocks become inefficient at high load, ie more = better eff
Hi Vesi,
Did you send the HEX4M as promised a few days ago?
Regards
Wilco
Did you send the HEX4M as promised a few days ago?
Regards
Wilco
Wow, 8 line power supply. Some how i feel that 0,6 W/Gh just a dream
Hi,
only based on official Avalon specs.
We'll be able to provide more info in a few days
Regards: Vesi
only based on official Avalon specs.
We'll be able to provide more info in a few days
Regards: Vesi
any initial figures on performance/watts
Jump to: