Antminer D3 Blissz firmware (10/12 v1.12 update) - page 113.

cryptonitro

full member

Activity: 348

Merit: 119

Quote from: blissz on November 16, 2017, 05:54:47 PM

Quite a good result I would say for the November batch. At stock settings my October batch did 13.5 Mh/s @ 900 watts. :/ Currently it's doing 14.8 Mh/s at 720 watts.
The fee is time based as I want to add balancing strategy to the firmware later

hope miner will not stop if you fee time cannot connect to your pool or else reason,
a good option to had is auto reboot if miner hangs or going to fault statut

blissz

sr. member

Activity: 336

Merit: 258

Quote from: dottat on November 16, 2017, 03:06:32 PM

Ok... so Nov batch here. Voltage lowest and freq sweet spot ended up being 437mhz.

Wattage currently is 770.4. Unit is hashing 15,378.2 currently.

Not complaining but how did you get the 1.5% miner integrated? Does that work concurrently or is it time based? Only interested because it's a pool feature i'm interested in.

Quite a good result I would say for the November batch. At stock settings my October batch did 13.5 Mh/s @ 900 watts. :/ Currently it's doing 14.8 Mh/s at 720 watts.
The fee is time based as I want to add balancing strategy to the firmware later

blissz

sr. member

Activity: 336

Merit: 258

Thank you for the feedback guys. If you flash it you can just keep your settings when flashing the firmware.

This is really first version and I will continue improving the firmware as it's far from perfect yet.
Beside some bugs that need to be fixed, I plan to add some requested features:

customize fail over / balance strategy
create auto tune profiles (silent, normal, performance), which will search for the best settings based on counting HW errors.
day / night profiles

The search for other algo's continues as I know this would be really bad ass to have. Cool

bbroge

newbie

Activity: 7

Merit: 0

Hey, First of all, thank you very much for this firmware. I am so glad I'm able to quiet this thing down. I tried it on my September version today. I've always had some hardware errors. From what I understand some are okay. I have to basically set my frequency to under 400 before I stop getting errors which severely affects my hash rate which should be much closer to 15G/Hs. Am I correct in assuming some errors are okay?

cryptonitro

full member

Activity: 348

Merit: 119

i read for install the frimware, but for precision , we have to use "flash new firmware , or better with "restore backup" ?

if with flash new firmware , "keep setting" must be checked ?

1.5 fee is high without algos , but i m happy to comforting your job with it Wink

dottat

newbie

Activity: 48

Merit: 0

Guessing that's because it's a beta. One other bug I noticed is that after you change the voltage once, setting it back to default doesn't actually do that. I found that out after setting it back to default and raising the clock speed up and seeing the HW errors jump like crazy.

Maicol792

legendary

Activity: 1260

Merit: 1010

i'm testing this public beta,

but when i change Asic Freq and return on webpage i can see last Freq i have imposted... but Asic Voltage i see "Default Setting"... and i can't see the value imposted.. why?

andresrp

member

Activity: 135

Merit: 11

PM Sent

mcan

member

Activity: 70

Merit: 10

Quote from: mcan on November 16, 2017, 03:19:10 PM

Where is default webpage located in cgminer-dash-master source codes ?

So antminer's main board is beagleboard black and , so as i understand cgminer just an application on it.
And firmware source belongs to the just cgminer , is this correct ?
So need to modify beaglebone black firmware to modify web pages which belongs to gui ?

mcan

member

Activity: 70

Merit: 10

Where is default webpage located in cgminer-dash-master source codes ?

dottat

newbie

Activity: 48

Merit: 0

I did not test that. Also, I was seeing speeds over 20 on my stock setup with all stock settings so you might be able to get 17 still while underclocked.

stugots2

full member

Activity: 224

Merit: 102

Too Many Miners Not Enough Electricity

Quote from: CrownRoyal79 on November 16, 2017, 01:41:38 PM

My one and only D3 (19.3 GH batch) just arrived today. Would anybody like to buy it and the APW3++ PSU? The miner is still in the original box, unopened. $600 plus shipping.

PM'd you

CrownRoyal79

newbie

Activity: 35

Merit: 0

Quote from: dottat on November 16, 2017, 03:06:32 PM

Ok... so Nov batch here. Voltage lowest and freq sweet spot ended up being 437mhz.

Wattage currently is 770.4. Unit is hashing 15,378.2 currently.

Not complaining but how did you get the 1.5% miner integrated? Does that work concurrently or is it time based? Only interested because it's a pool feature i'm interested in.

Did you underclock the default Bitmain firmware and look at wattage? I just received a 19.3 GH/s (November batch) today. Will underclocking give me 17 GH/s at under 1000 watts?

dottat

newbie

Activity: 48

Merit: 0

Ok... so Nov batch here. Voltage lowest and freq sweet spot ended up being 437mhz.

Wattage currently is 770.4. Unit is hashing 15,378.2 currently.

Not complaining but how did you get the 1.5% miner integrated? Does that work concurrently or is it time based? Only interested because it's a pool feature i'm interested in.

mag34

newbie

Activity: 1

Merit: 0

Гoтoв кyпить

mcan

member

Activity: 70

Merit: 10

which compiler did you used to compile source codes?

dndssc

full member

Activity: 266

Merit: 102

Quote from: D3 Antminer on November 16, 2017, 01:14:25 PM

Probably ,
it will be the most anticipated and demanding modding work of near history.

https://www.change.org/p/https-twitter-com-bitmaintech-d3-antminer-firmware-update-for-additional-mining-algorithms?recruiter=831205993&utm_source=share_petition&utm_medium=copylink&utm_campaign=share_petition&utm_term=share_petition

LOL over 6 hundred subscriptions

CrownRoyal79

newbie

Activity: 35

Merit: 0

My one and only D3 (19.3 GH batch) just arrived today. Would anybody like to buy it and the APW3++ PSU? The miner is still in the original box, unopened. $600 plus shipping.

crackfoo

legendary

Activity: 3556

Merit: 1126

Does anyone have any watt comparisons yet?

D3 Antminer

member

Activity: 94

Merit: 10

Probably ,
it will be the most anticipated and demanding modding work of near history.

https://www.change.org/p/https-twitter-com-bitmaintech-d3-antminer-firmware-update-for-additional-mining-algorithms?recruiter=831205993&utm_source=share_petition&utm_medium=copylink&utm_campaign=share_petition&utm_term=share_petition

Topic: Antminer D3 Blissz firmware (10/12 v1.12 update) - page 113. (Read 125911 times)