I have rig with 4 vega 56@64.
I just unistall block chain driver with display driver uninstaller. Reboot and install 18.3.4 and same powertable reg file i used with old drivers (1408@850 and 1100@900),disable crossfire and all is ok.
Rig draw ~700w at the wall (CryptoNotev7) and ~650w at the wall (CryptoNote-Heavy)
Topic: [Cast XMR] high speed XMR/CryptoNight miner for RX Vega GPUs (2 KHash/s) - page 30. (Read 206388 times)
May 26, 2018, 02:55:27 PM
May 26, 2018, 01:40:36 PM
hi
i'm still on blockain with 4 vega 56@64 and powertable 1100 mhz of the "Monero and Vega - the definitive guide MoneroMining"
it draw 700w at the wall with 1408@850 and 1100@900
i tried with the 18.3.4,same hashrate +/- 7900h no power table but 1408@850 and 1100@900 with overdrivetool.
But there is a massive difference:it draw 1000w at the wall
i don't kwnow why,core and mee was same exept powertable.
where can i find powertable for adrenaline 18.3.4 or 18.5.1? or make them even i'm not understanding all :/
thanks
i'm still on blockain with 4 vega 56@64 and powertable 1100 mhz of the "Monero and Vega - the definitive guide MoneroMining"
it draw 700w at the wall with 1408@850 and 1100@900
i tried with the 18.3.4,same hashrate +/- 7900h no power table but 1408@850 and 1100@900 with overdrivetool.
But there is a massive difference:it draw 1000w at the wall
i don't kwnow why,core and mee was same exept powertable.
where can i find powertable for adrenaline 18.3.4 or 18.5.1? or make them even i'm not understanding all :/
thanks
May 26, 2018, 08:43:23 AM
A little help please: GPU 0 in my 5 card rig is showing fan speed of -1 rpm and temp of -1* C. It’s not the card, riser, or cable, as both Wattman and GPUz shows fan speed and temp. If I rearrange the riser cables, it’s always GPU 0 not reading sensors. Any ideas?
May 26, 2018, 01:36:27 AM
reboot your computer. if still no info, try to contact the developers of software
May 25, 2018, 02:44:57 PM
Do you have an English version of that software? that's the first one I saw capable of seeing the whole wattage of vegas. Gpuz(Nvidia only)hwinfo64(must add core/memory/chip power), msi afterburner(Nvidia only).
It might have English. Downloaded from this link: http://rh-software.com/
Missing wattages should I just leave it for few hours? May 25, 2018, 01:32:51 PM
Hey guys,
AMD released a new driver today - 18.5.1
I haven´t done further testing, but it looks like my hashrate improved of around 1-3%. (mining Cryptonight-Heavy)
(source: https://www.guru3d.com/news-story/download-radeon-software-adrenalin-edition-18-5-1.html)
AMD released a new driver today - 18.5.1
I haven´t done further testing, but it looks like my hashrate improved of around 1-3%. (mining Cryptonight-Heavy)
(source: https://www.guru3d.com/news-story/download-radeon-software-adrenalin-edition-18-5-1.html)
On my Vegas it may have actually decreased the hash rate.
Especially on the 56 ones with 64 BIOS.
It seems all my Vega 64's have dropped very slightly with this driver as well.
May 25, 2018, 12:25:37 PM
Hi,
I am th developer of the free monitoring tool - rig-monitor. I have just released version 2.1 which supports Cast XMR.
Check it out here https://bitcointalksearch.org/topic/new-free-rig-monitor-40-alpha-released-2128602
Thanks
I am th developer of the free monitoring tool - rig-monitor. I have just released version 2.1 which supports Cast XMR.
Check it out here https://bitcointalksearch.org/topic/new-free-rig-monitor-40-alpha-released-2128602
Thanks
May 25, 2018, 10:08:03 AM
Hey guys,
AMD released a new driver today - 18.5.1
I haven´t done further testing, but it looks like my hashrate improved of around 1-3%. (mining Cryptonight-Heavy)
(source: https://www.guru3d.com/news-story/download-radeon-software-adrenalin-edition-18-5-1.html)
AMD released a new driver today - 18.5.1
I haven´t done further testing, but it looks like my hashrate improved of around 1-3%. (mining Cryptonight-Heavy)
(source: https://www.guru3d.com/news-story/download-radeon-software-adrenalin-edition-18-5-1.html)
On my Vegas it may have actually decreased the hash rate.
Especially on the 56 ones with 64 BIOS.
May 25, 2018, 09:05:23 AM
What's your power draw per card?
I don't have wattmeter, so I can only check with software: https://imgur.com/iO3DdsL
It might have English. Downloaded from this link: http://rh-software.com/
May 25, 2018, 09:04:34 AM
@glph3k
Do you plan to include the changes for ETN (https://github.com/electroneum/electroneum/releases/tag/v2.0.0.0) in the near future?
Thanks and best regards.
Do you plan to include the changes for ETN (https://github.com/electroneum/electroneum/releases/tag/v2.0.0.0) in the near future?
Thanks and best regards.
May 25, 2018, 07:37:28 AM
I installed pure amd driver. How can i disable HBCC options is in regedit?
Same problem with me. It I disable HBCC, I get half the hash rates. May 25, 2018, 03:33:05 AM
What's your power draw per card?
I don't have wattmeter, so I can only check with software:
May 25, 2018, 01:42:45 AM
For v64 just start with --maxmem, its better than w/o.
my vega64 with --maxmem performs 1130 H/s, without --maxmem 1530 H/s on CastXMR
May 25, 2018, 01:12:04 AM
1) yes, that is true. 2) I installed pure Display Driver, no AMD settings or anything else (ASUS GPU Tweak works better than AMD Wattman for me). 3) all answers on screenshot of my settings and mining result. My card is ASUS ROG STRIX Radeon RX Vega64 8GB OC , samsung memory.
https://imgur.com/U6rwljk
https://imgur.com/U6rwljk
Do you think you could keep this stable for over a week haha. You are running it at 1708MHz core?? custom regedit? i have been primarily using just overdriventool and tweaking to 1408/950 core and 950/900 mem
What for your "haha"? I installed new driver just today with the settings like on screenshot, it is stable for half a day, after 1 week i will tell you how it behaves . Still I hope CAST XMR will update in a couple of days and we will all have +50% hashrates
No, i didn't regedit windows. Just drivers+GPU Tweak from Asus+miner.What's your power draw per card?
I don't have wattmeter, so I can only check with software: https://imgur.com/iO3DdsL
May 24, 2018, 11:58:16 PM
I've been using cast xmr for a long time without any single issue...recently I switched to cr heavy algo, got fantastic hashrates around 7200h/s (5xVega56 rig) but soon after i noticed that the miner freezes sometime. It just stops updating the status but still drawing a lot of electricity (750w).
Here's the settings i use:
1407/950 core and 950/910 mem
-I 9 --opencl 0 -G 0,1,2,3,4 -S --nonicehash --fastjobswitch --algo 2
Do you maybe know what could cause the problem?
I also noticed that the hashrate changes after restarting the miner. Sometimes it starts 6200 and after several minutes it reaches 6600, sometimes it starts with 6900 and reaches 7250...Do you know why this happens?
About core/mem. You can set 1510-1530 core, its stable with 950mV and faster hashing. For mem I use 880mV, more don't give more hashes, but little less power consumption.Here's the settings i use:
1407/950 core and 950/910 mem
-I 9 --opencl 0 -G 0,1,2,3,4 -S --nonicehash --fastjobswitch --algo 2
Do you maybe know what could cause the problem?
I also noticed that the hashrate changes after restarting the miner. Sometimes it starts 6200 and after several minutes it reaches 6600, sometimes it starts with 6900 and reaches 7250...Do you know why this happens?
About hash rate. With CastXmr 1.0 to reach 1550+-h/s My v56 I need start with --maxmem option, after 1-2 accepted shares, close miner and run without --maxmem. For v64 just start with --maxmem, its better than w/o.
Solution: just try to play with --maxmem option.
May 24, 2018, 06:56:27 PM
I've been using cast xmr for a long time without any single issue...recently I switched to cr heavy algo, got fantastic hashrates around 7200h/s (5xVega56 rig) but soon after i noticed that the miner freezes sometime. It just stops updating the status but still drawing a lot of electricity (750w).
Here's the settings i use:
1407/950 core and 950/910 mem
-I 9 --opencl 0 -G 0,1,2,3,4 -S --nonicehash --fastjobswitch --algo 2
Do you maybe know what could cause the problem?
I also noticed that the hashrate changes after restarting the miner. Sometimes it starts 6200 and after several minutes it reaches 6600, sometimes it starts with 6900 and reaches 7250...Do you know why this happens?
Here's the settings i use:
1407/950 core and 950/910 mem
-I 9 --opencl 0 -G 0,1,2,3,4 -S --nonicehash --fastjobswitch --algo 2
Do you maybe know what could cause the problem?
I also noticed that the hashrate changes after restarting the miner. Sometimes it starts 6200 and after several minutes it reaches 6600, sometimes it starts with 6900 and reaches 7250...Do you know why this happens?
May 24, 2018, 04:20:17 PM
Hello,
did you have problem with your rig when you used compute gpu workload ? My rig is all time frozen when i switch gpu workload to compute, but with graphic gpu workload its ok.
did you have problem with your rig when you used compute gpu workload ? My rig is all time frozen when i switch gpu workload to compute, but with graphic gpu workload its ok.
May 24, 2018, 12:36:49 PM
Just tried to run V1.0, with win 10 X64 (build 1803) + AMD 18.3.4 drivers + 3X RX570 bios mod + afterburner 4.5. Only 2 cards are working properly, GPU1 has less than 70H/s when displayed.
Here is my bat:
cast_xmr-vega --algo=-1 -S xmr-us-east1.nanopool.org:14444 -G 0,1,2 --forcecompute -u 45KjUS75gPfatjfHjtBkEed********GEwKGEDWk545ZWQd9ieFGcm.Z****t
What am I missing please ?
Here is my bat:
cast_xmr-vega --algo=-1 -S xmr-us-east1.nanopool.org:14444 -G 0,1,2 --forcecompute -u 45KjUS75gPfatjfHjtBkEed********GEwKGEDWk545ZWQd9ieFGcm.Z****t
What am I missing please ?
algo=1 not -1
May 24, 2018, 09:57:03 AM
1) yes, that is true. 2) I installed pure Display Driver, no AMD settings or anything else (ASUS GPU Tweak works better than AMD Wattman for me). 3) all answers on screenshot of my settings and mining result. My card is ASUS ROG STRIX Radeon RX Vega64 8GB OC , samsung memory.
https://imgur.com/U6rwljk
https://imgur.com/U6rwljk
Do you think you could keep this stable for over a week haha. You are running it at 1708MHz core?? custom regedit? i have been primarily using just overdriventool and tweaking to 1408/950 core and 950/900 mem
What for your "haha"? I installed new driver just today with the settings like on screenshot, it is stable for half a day, after 1 week i will tell you how it behaves . Still I hope CAST XMR will update in a couple of days and we will all have +50% hashrates
No, i didn't regedit windows. Just drivers+GPU Tweak from Asus+miner.What's your power draw per card?
May 24, 2018, 09:10:20 AM
1) yes, that is true. 2) I installed pure Display Driver, no AMD settings or anything else (ASUS GPU Tweak works better than AMD Wattman for me). 3) all answers on screenshot of my settings and mining result. My card is ASUS ROG STRIX Radeon RX Vega64 8GB OC , samsung memory.
https://imgur.com/U6rwljk
https://imgur.com/U6rwljk
Do you think you could keep this stable for over a week haha. You are running it at 1708MHz core?? custom regedit? i have been primarily using just overdriventool and tweaking to 1408/950 core and 950/900 mem
What for your "haha"? I installed new driver just today with the settings like on screenshot, it is stable for half a day, after 1 week i will tell you how it behaves . Still I hope CAST XMR will update in a couple of days and we will all have +50% hashrates
No, i didn't regedit windows. Just drivers+GPU Tweak from Asus+miner. Jump to: