Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 1119.

Trimegistus

legendary

Activity: 1564

Merit: 1027

Quote from: xeridea on September 17, 2016, 10:33:11 AM

Use GPU-Z to check memory manufacturer. If it is Samsung it will OC awesome, if not, it will only OC a little. From the cards I have, all the Nitro 8GB are Samsung, the 4GB tend to be Hynix.

Yep, you're right. All my cards have Hynix memory chips. I don't want to OC, I want to UV... undervolt! Grin

And right now, I believe I've found the sweet spot:

GPU: 900 MHz, 800 mV
Mem: 1750 MHz, 800 mV

Speed per card: 22 MHs ETC, 275 MHs SC
Power per card: ~55W (GPU-Z)

-dcri 25
-ethi 16

Cheesy

xeridea

sr. member

Activity: 449

Merit: 251

Quote from: Trimegistus on September 16, 2016, 06:58:04 PM

Quote from: molitar on September 16, 2016, 06:41:46 PM

The Nitro+ 8GB can easily do 2250 MHz memory.

What about the Nitro+ 4GB?

Any experience with those?

Mine crash as soon as I set memclock above 1875... Huh

Win10 x64, driver 16.9.1

Any ideas?

Use GPU-Z to check memory manufacturer. If it is Samsung it will OC awesome, if not, it will only OC a little. From the cards I have, all the Nitro 8GB are Samsung, the 4GB tend to be Hynix.

micairvas

full member

Activity: 303

Merit: 105

Quote from: xxcsu on September 16, 2016, 01:55:17 PM

Quote from: micairvas on September 16, 2016, 12:36:51 PM

Hi guys, can someone help me to make my rig working (6 x Asus Rx470 Strix 4gb)? As soon as I start mining, application crashes,getting error message = driver stop working. With 1 gpu, Claymore miner working normally. I tried different drivers, currently I have installed 16.9.1. (win 10-64 bit). Do I need to change .bat file or something? Does anyone have 6 rx470 card rig working as expected?

Are u sure your power supply can handle your setup power draw ?
try each card one by one , if all working as a single card setup the cards are ok .
next try to connect 2 on the same time , start the miner , then 3 , then 4 , then 5 , then 6 , and see how many cards hashing without error
if you have 3-4 or 5 card working fine, then maybe you will need a bigger power supply ...
if you installed or updated drivers , uninstall them , remove completly , boot the pc with one card installed , install amd driver , reboot , turn off your pc , connect all cards , and be patient when you pc is booting up with all 6 card connected , windows need some time to assign the driver for each card , it sometimes take a few minutes your screen may will flashing , flickering during this time. wait wait and wait dont start the miner or wattman , if you do your vga driver will crash

Power supply is LC1200 V2.4
http://www.lc-power.com/en/product/netzteile/platinum-series/lc1200-v24/
It must be strong enough regarding specification. I succeed to start rig working with 4 cards ant that is it. Not working with 5-6 cards.

Satisun

newbie

Activity: 14

Merit: 1

Quote from: melsell1 on September 17, 2016, 12:23:24 AM

I have 3x r9 380x in 0,1,2 slots and 3x rx 480 in 3,4,5 slots but in miner there is a mess and 1 card is trolling and i don't know which one.

Pic: https://www.upload.ee/image/6171171/troll.jpg

How to correct that mess?

You can remove one card at a time in the PCIE slot. Or you can use the comment -di

-di GPU indexes, default is all available GPUs. For example, if you have four GPUs "-di 02" will enable only first and third GPUs (#0 and #2).

xxcsu

hero member

Activity: 1498

Merit: 597

Quote from: Kompik on September 16, 2016, 04:36:26 PM

When I am mining LBRY + ETH i get only 55MH/s on libry at maximum. Is this the norm? Or is there some secret to it?

Thanks!

need just a little bit more info Grin

mining on what hardware ? what op system ? what vga card AMD ? nVidia ? what driver ?
Grin

melsell1

newbie

Activity: 50

Merit: 0

Quote from: doktor83 on September 17, 2016, 12:35:53 AM

you are trolling us with that tiny image Grin

Ohhh

now is better. changed the link

doktor83

hero member

Activity: 2548

Merit: 626

you are trolling us with that tiny image Grin

melsell1

newbie

Activity: 50

Merit: 0

I have 3x r9 380x in 0,1,2 slots and 3x rx 480 in 3,4,5 slots but in miner there is a mess and 1 card is trolling and i don't know which one.

Pic: https://www.upload.ee/image/6171171/troll.jpg

How to correct that mess?

wll1rah

full member

Activity: 209

Merit: 100

Quote from: Joemid on September 16, 2016, 03:10:01 PM

Quote from: wll1rah on September 16, 2016, 02:36:35 PM

Quote from: madpacket on September 16, 2016, 09:10:58 AM

Quote from: xeridea on September 15, 2016, 11:44:37 PM

Quote from: madpacket on September 15, 2016, 11:07:05 PM

Quote from: madpacket on September 15, 2016, 09:49:47 PM

Quote from: madpacket on September 15, 2016, 09:37:04 PM

Quote from: wll1rah on September 15, 2016, 09:24:12 PM

Quote from: madpacket on September 15, 2016, 09:06:44 PM

Hello Claymore. I've been using your miner for 30+ Radeon 480's and several 390's / Fury X's. Great software with very little problems. I have recommended your software to all my mining friends which they use. I hope you can help with a problem.

I purchased a single Geforce 1070 and cannot get it to mine. I'm running Windows 10 Anniversary update with the latest drivers. I've used the same working batch file that work with my Radeons. When I launch my batch file I get an error from EthDcrMiner64.exe (latest version 7) saying

"The program can't start because OpenCL.DLL is missing from your computer. Try reinstalling the program to fix this problem."

I have verified OpenCL.dll exists on my Windows system. I tried copying opencl.dll locally to the root mining folder (with the EthDcrMiner exe) and I get an error stating "The application was unable to start correctly (0X000007B). Click OK to close the application."

After some Googling I read new Nivida drivers corrupt OpenCL.dll when overwriting the file. So tired repair instructions listed under this website https://appuals.com/repair-corrupt-opencl-dll-in-windows-10/ which did not help me.

I'm a total newbie with Nvidia Pascal mining, can you please help? I read through your readme documentation and I see nothing specific to Nvidia cards that I should be doing to get this working. I'm at a loss and need your help.

Thanks in advance!

try with just the basics first meaning just the pool/s configuration for mining. If you didn't change the start.bat file just try that. I have to 1060 3GB that I have used since he added NV support without issue.
Also If you didn't do a clean install of your drivers for NVidia for windows 10 after the update it causes problems.

Thanks for the reply. I didn't make any changes to my working batch file. I simply ran it after the anniversary update and it complained about OpenCL missing. I just ran DDU and reinstalling the Nvidia drivers recommended on the first page.

My batch file for reference looks like this:

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal Mining_Address.MinerName -epsw x

Nevermind. I updated to the latest DDU verson, uninstalled previous driver in safe mode and installed the recommended drivers on the first page and now I'm mining away with my ITX Gigabyte 1070! Thanks for your help.

Seems to be working fine. Mining speeds are a little lower then expected at 24.5 - 25Mh. I haven't done any overclocking at all, this is just stock. I believe this card has Micron memory (according to GPU-Z) so I'm not sure if that's going to hold it back but I'll report back my hashes after overclocking.

Happy now!

Next project, flash 32 Radeon 480's with custom BIOS to bring up overall hash speeds 100+Mh. This will take a while heh. What's the recommended remote desktop software around here? TeamViewer?

OK spent a few hours tweaking power settings and overclocking / underclocking. I think I have pretty decent results for this tiny ITX Gigabyte 1070, what do you think?

Nvidia cards aren't as good for Ethereum costwise. They do OK, but not for the cost. They don't dual mine as well either. Currently it is better to min LBRY with them. I can get ~$50-55/month from a 470 with stock clocks, on Eth+Sia. A 1060 3GB gets $40/month for similar cost. However LBRY it will get ~$50/month. So it is still profitable on them, just somewhat better to do LBRY right now, but it also depends on price/difficulty of that, which moves a lot.

There is a private miner for LBRY, but I don't like the idea of paying for miner, that also has a high devfee, with only slightly faster hashing, and wouldn't be worth it unless you had multiple nvidia rigs. From the thread on it, it is also unstable at some pools due to poor network code. The dev isn't really friendly either.

Thanks. Appreciate the feedback. I'm well aware Radeon's are better for mining Ether, hence why I'm mining at over a Gh with 30+ cards already. I bought the 1070 as I needed a low powered ITX card to fit in my HTPC and serve double duty. As for mining some altcoin like LBRY I generally don't bother with as I mine Ether and hold with the expectation it'll rise in value over the next few years. These alt coins (and LBRY looks like something that's being done in Ethereum anyway) come and go and are mainly good if you are immediately trading. I'll keep my eye on it but for now I rather get another 30Mh out of this 1070 mining Ether.

Why is your memory clock so low on your GTX 1070 in your picture it says it's set to 1350 and I'm assuming that is its base frequency which means its only running at 5400 Mhz effective on your 1070 which is really low. it should be closer to 8000 effective if not hight

Low memory clock is not better to mining?

ETH and coins like it are memory intensive, so overclocking mem is preferred to the gpu core you may still need to overclock the gpu core but NVidia takes care of that all you need to do for there cards is adjust power limits.

delle54

sr. member

Activity: 307

Merit: 250

Quote from: molitar on September 16, 2016, 06:41:46 PM

Not only that you can do much much better with your settings using WattTool.

THX very much for the tips. Memclock is running stable at 2200 MHz for now. Will test WattTool and the the rest tomorrow.

Trimegistus

legendary

Activity: 1564

Merit: 1027

Quote from: molitar on September 16, 2016, 06:41:46 PM

The Nitro+ 8GB can easily do 2250 MHz memory.

What about the Nitro+ 4GB?

Any experience with those?

Mine crash as soon as I set memclock above 1875... Huh

Win10 x64, driver 16.9.1

Any ideas?

molitar

sr. member

Activity: 322

Merit: 250

Quote from: delle54 on September 16, 2016, 05:34:31 PM

Quote from: molitar on September 15, 2016, 08:07:26 PM

Seems to be a severe problem with v 7.0 as my mining speed drops from 23.9 MHs on my RX 480 card down to 15.x MHs. That is a huge performance drop

I agree. I'm running v 6.4 again, which is much faster -> now 25 Mh/s. Mining ETH+SIA (-dcri 40 @500 Mh/s) on a Sapphire RX 480 8 GB Nitro+, undervolted to 1.0500 mv, GPU Mem. Clk. 2100 MHz.

The Nitro+ 8GB can easily do 2250 MHz memory.

http://molitar.no-ip.org:9510/mining-infos.json

Not only that you can do much much better with your settings using WattTool.

delle54

sr. member

Activity: 307

Merit: 250

Quote from: TR8888 on September 16, 2016, 04:46:51 PM

I generally get 16.4-16.7 Mh/s on ethereum now with 280x's, I have many of them and only a couple get 17 mh's now, All elpida memory... Is this normal?

For the R9 280x this is normal. Try tweaking your GPU Mem. Clk. gradually and slowly, since ETH is memory intensive. Don't await miracles though, because the difficulty is rising from day to day.

delle54

sr. member

Activity: 307

Merit: 250

Quote from: molitar on September 15, 2016, 08:07:26 PM

Seems to be a severe problem with v 7.0 as my mining speed drops from 23.9 MHs on my RX 480 card down to 15.x MHs. That is a huge performance drop

I agree. I'm running v 6.4 again, which is much faster -> now 25 Mh/s. Mining ETH+SIA (-dcri 40 @500 Mh/s) on a Sapphire RX 480 8 GB Nitro+, undervolted to 1.0500 mv, GPU Mem. Clk. 2100 MHz.

TR8888

hero member

Activity: 525

Merit: 500

I generally get 16.4-16.7 Mh/s on ethereum now with 280x's, I have many of them and only a couple get 17 mh's now, All elpida memory... Is this normal?

Kompik

sr. member

Activity: 463

Merit: 250

When I am mining LBRY + ETH i get only 55MH/s on libry at maximum. Is this the norm? Or is there some secret to it?

Thanks!

Joemid

newbie

Activity: 44

Merit: 0

Quote from: wll1rah on September 16, 2016, 02:36:35 PM

Quote from: madpacket on September 16, 2016, 09:10:58 AM

Quote from: xeridea on September 15, 2016, 11:44:37 PM

Quote from: madpacket on September 15, 2016, 11:07:05 PM

Quote from: madpacket on September 15, 2016, 09:49:47 PM

Quote from: madpacket on September 15, 2016, 09:37:04 PM

Quote from: wll1rah on September 15, 2016, 09:24:12 PM

Quote from: madpacket on September 15, 2016, 09:06:44 PM

Hello Claymore. I've been using your miner for 30+ Radeon 480's and several 390's / Fury X's. Great software with very little problems. I have recommended your software to all my mining friends which they use. I hope you can help with a problem.

I purchased a single Geforce 1070 and cannot get it to mine. I'm running Windows 10 Anniversary update with the latest drivers. I've used the same working batch file that work with my Radeons. When I launch my batch file I get an error from EthDcrMiner64.exe (latest version 7) saying

"The program can't start because OpenCL.DLL is missing from your computer. Try reinstalling the program to fix this problem."

I have verified OpenCL.dll exists on my Windows system. I tried copying opencl.dll locally to the root mining folder (with the EthDcrMiner exe) and I get an error stating "The application was unable to start correctly (0X000007B). Click OK to close the application."

After some Googling I read new Nivida drivers corrupt OpenCL.dll when overwriting the file. So tired repair instructions listed under this website https://appuals.com/repair-corrupt-opencl-dll-in-windows-10/ which did not help me.

I'm a total newbie with Nvidia Pascal mining, can you please help? I read through your readme documentation and I see nothing specific to Nvidia cards that I should be doing to get this working. I'm at a loss and need your help.

Thanks in advance!

try with just the basics first meaning just the pool/s configuration for mining. If you didn't change the start.bat file just try that. I have to 1060 3GB that I have used since he added NV support without issue.
Also If you didn't do a clean install of your drivers for NVidia for windows 10 after the update it causes problems.

Thanks for the reply. I didn't make any changes to my working batch file. I simply ran it after the anniversary update and it complained about OpenCL missing. I just ran DDU and reinstalling the Nvidia drivers recommended on the first page.

My batch file for reference looks like this:

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

EthDcrMiner64.exe -epool us1.ethermine.org:4444 -ewal Mining_Address.MinerName -epsw x

Nevermind. I updated to the latest DDU verson, uninstalled previous driver in safe mode and installed the recommended drivers on the first page and now I'm mining away with my ITX Gigabyte 1070! Thanks for your help.

Seems to be working fine. Mining speeds are a little lower then expected at 24.5 - 25Mh. I haven't done any overclocking at all, this is just stock. I believe this card has Micron memory (according to GPU-Z) so I'm not sure if that's going to hold it back but I'll report back my hashes after overclocking.

Happy now!

Next project, flash 32 Radeon 480's with custom BIOS to bring up overall hash speeds 100+Mh. This will take a while heh. What's the recommended remote desktop software around here? TeamViewer?

OK spent a few hours tweaking power settings and overclocking / underclocking. I think I have pretty decent results for this tiny ITX Gigabyte 1070, what do you think?

http://imgur.com/a/Mfj9P

Nvidia cards aren't as good for Ethereum costwise. They do OK, but not for the cost. They don't dual mine as well either. Currently it is better to min LBRY with them. I can get ~$50-55/month from a 470 with stock clocks, on Eth+Sia. A 1060 3GB gets $40/month for similar cost. However LBRY it will get ~$50/month. So it is still profitable on them, just somewhat better to do LBRY right now, but it also depends on price/difficulty of that, which moves a lot.

There is a private miner for LBRY, but I don't like the idea of paying for miner, that also has a high devfee, with only slightly faster hashing, and wouldn't be worth it unless you had multiple nvidia rigs. From the thread on it, it is also unstable at some pools due to poor network code. The dev isn't really friendly either.

Thanks. Appreciate the feedback. I'm well aware Radeon's are better for mining Ether, hence why I'm mining at over a Gh with 30+ cards already. I bought the 1070 as I needed a low powered ITX card to fit in my HTPC and serve double duty. As for mining some altcoin like LBRY I generally don't bother with as I mine Ether and hold with the expectation it'll rise in value over the next few years. These alt coins (and LBRY looks like something that's being done in Ethereum anyway) come and go and are mainly good if you are immediately trading. I'll keep my eye on it but for now I rather get another 30Mh out of this 1070 mining Ether.

Why is your memory clock so low on your GTX 1070 in your picture it says it's set to 1350 and I'm assuming that is its base frequency which means its only running at 5400 Mhz effective on your 1070 which is really low. it should be closer to 8000 effective if not hight

Low memory clock is not better to mining?

manlabor

newbie

Activity: 25

Merit: 0

Quote from: BenCodie on September 16, 2016, 07:25:37 AM

is it auto start Miner(Mining)
Means to say if my pc restarted or shutdown unexpectedly this miner start(restart) automatically and start mining?
Sorry for noob questions as i going to start Mining now

another noob question how to join a pool like ethpool or nanopool
I am going to setup 3 rigs with 5gpu's on each of them so my question is how to join the pool for each of coin this Miner supports

Thanks in advance

Start with BIOS settings on motherboard. You usually have three options after a power loss event: Shut Off, Turn On, Return to Previous State

Next would depend on your operating system. For Windows, add program to startup folder. For Linux, add program to Startup Applications.

Follow the directions provided on the pool website. If you are just starting, I would get some equipment (maybe just one video card) and get that up and running.