Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 145. (Read 6590757 times)

You are mining for a ~minute every 2 and a half hours, approx
What are you really losing here? I don't get it?


depends on how many Mhs of mining speed do you have, but, even small/old rigs can get some ZILs, based on a month

I mined ZIL till difficulty was OK. Now the PoW difficulty is damn high. This is one pool's quote: "Please note: At the current difficulty to find a valid share you need around 5 GH/s. So if you mine with 500 MH/s, excluding luck, you need 10 rounds to see earning" (see original at https://zilliqaminer.com/#start_mining)
Any way, for AMD I used https://github.com/DanSoQt/ZilSwitcher, but now stopped.

What do you mean by "custom"?
For long time it's not profitable for me either.

you are mining the wrong dual than
do you have tried ZIL in "custom" dual?
give a try and you'll see the positive results

At my point of view, dual is not profitable, or the same as mono, except free socket. In my case mono mode takes apr. 800w for 6 cards RX480 and dual mode takes apr. 1050w.

I know, I went through them. There are a lot of tweaks possible, that's why I'm asking what the most profitable command (for now) could be. Also what coins would that be.

You can find many dual examples on the head of this topic.

Hi,

New here. I've been mining with PhoenixMiner and just found out I can dual mine. Phoenixminer only supports blake2s which would earn me 1$ a year when I dual mine on my 6xP106-100 6gb miner.

I see that most of the commands are the same with Claymore. Now I'm using this:

commandserver1=PhoenixMiner.exe -pool us1.ethermine.org:4444 -wal MyEthWalletAddress.name -coin eth -proto 3 -dpool blake2s.eu.nicehash.com:3361 -dwal NicehashBitcoinAddress-dcoin blake2s -log 1 -logfile miner.log

What command would I have to use to mine most profitable on Claymore?

Thanks guys!

right click miner exe / properties / compatibility and check the box start program as administrator. then run the batch normally

does it work on the amd vii ??

you need to use a command line, go to start -> cmd -> right click for use as admin and than type the eth install command

after that you can run the bat as normal, no need admin

I run the Claymore 14.1 and 14.0, the differences seem to be the way the card is handling the straps is subtle, but there is a little bit of a difference on the Polaris cards.

Our group is seeing some cards that have not as good of memory, with settings that work great in 14.0 are having throttling and blue screen issues on 14.1.

Also experiencing some weird strap errors on one of my Vega's, but it might be my card. It says it cannot apply strap setting to this device.

I am seeing the Polaris on the cards running much better on 14.1 when the memory is good.
I had a card go from 31.2 to 31.5 for my Sapphire 590. and my 570 went from 30.68 to 31.2 mhs. Running at 2250 strap and 850 core voltage.

Make sure when you set your straps, and if you have different cards or memory types, I strongly suggest using the command line to control your voltage & clock speeds via cclock, cvddc, mclock & mvddc.

I have experienced and seen other members with the cards on 14.1 and 14.0 act differently So you may need to manually setup each card this way. Only use the Wattman Tool & afterburner tools to control your fan speeds, until or unless Claymore states that he has resolved the fan control API issue.

We did have a couple members get their Vega 56's and 64's clock in 48Mhs to 50 Mhs but i was unsuccessful but i have issues with my cards.

With 14.0 and you have a mixed environment, do your -di 0,3 - if your RX are on card ID 0 & 3 then do after your strap code -di 0123, this actually will re assign port addresses to your cards. I had to do this with one of my rigs that is a  mixed Polaris / Vega. The Polaris will be come id's 0 & 1 then the Vega's became 2 & 3 instead of 0 & 2.

One question i have is, on the Polaris the strap tells you the POL8H1 - meaning Polaris 8 GB with Hynix memory as very helpful and informative, however the Strap does not provide any information as to its settings or card information with the Vega series. Is there a way to have the line display more information or is it a limitation of the driver?

With the AMD Tweak tool i was able to get my 570 to run at 2300 Strap but on the Claymore it clearly is cap'd at 2250. Any suggestions? 2300 will get a 570 to 32.1 Mhs.

I also wish we could hammer home to everybody, with the memory strap being controlled by the Miner, REGARDLESS if you've modded  your bios or not. The strap timings will be the same. As all the BIOS mod was doing was modifying the strap timings.

I know this post is all over sorry answering questions and posing a few while i'm at it.

Hello,everyone. To use new miner version could someone advise me the best driver for my RX 480 samsung 8Gb? Currently I'm using bc driver and get 31 Mh/sec with 1170/2150 overclocking.
Thanks in advance)

You probably need to disable secure boot in your computer's bios.

Got my stock bios rx 580 and I keep right clicking the batch and run as administrator and it keeps saying this. "Failed, you must run miner with admin rights." in red text. Please Help

with 16GBytes of memory, i guess it wouldn't be memory limited.  
Your post just said Vega... didn't specify 56/64/VII... so i asked, after i tried.

Open WattMan/AB and overclock memory. No changes in hashrate. Now overclock core and you will see higher hashrate.

And what is Radeon VII limited to?

"-strap" for Radeon7 is not supported, it is not memory-limited so I don't see any speedup when I change memory timings.

that's what i said... Radeon VII is Radeon Vega VII.

vega cards are Vega 56, Vega 64, and Vega VII... they all have HBM2