Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 326. (Read 6590565 times)

yeah, i know 11.2 and above is about fixing cheating programs because of ssl integration. but lots of others are affected especially stability. im getting random incorrect shares now within 24hrs. i never had my rigs run more than 24hrs due to this incorrect shares, because whenever i get incorrect shares i downclock mem, after that, i still get incorrect shares with random gpus and so on. cant keep mining for more than 24hrs due to this problem. i wanted to ignore it, but the rule is, incorrect/invalid/stales/rejected are wasted hashing power.

Can anybody help me with ethermine.org pool? I had not found the way to run Claymore with this pool.

I can see in console the following

ETH: Stratum - connecting to 'eu1.ethermine.org' <94.23.28.180> port 5555 (SSL/TLS)
No pool specified for Decred! Ethereum-only mining mode is enabled
ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)
ETH: eth-proxy stratum mode
Watchdog enabled
Remote management (READ-ONLY MODE) is enabled on port 3333

SSL/TLS encryption is enabled
Pool certificate verified successfully
ETH: Stratum - Connected (eu1.ethermine.org:5555) (SSL/TLS)
ETH: Share rejected!
GPU0 t=33C fan=41%, GPU1 t=36C fan=43%, GPU2 t=31C fan=41%, GPU3 t=30C fan=40%, GPU4 t=36C fan=43%, GPU5 t=33C fan=42%
ETH: Job timeout, disconnect, retry in 20 sec...
GPU0 t=31C fan=40%, GPU1 t=33C fan=42%, GPU2 t=29C fan=40%, GPU3 t=28C fan=40%, GPU4 t=34C fan=42%, GPU5 t=33C fan=41%
ETH: Stratum - connecting to 'eu1.ethermine.org' <51.255.64.43> port 5555 (SSL/TLS)
SSL/TLS encryption is enabled
Pool certificate verified successfully
ETH: Stratum - Connected (eu1.ethermine.org:5555) (SSL/TLS)
ETH: Share rejected!
GPU0 t=29C fan=40%, GPU1 t=31C fan=40%, GPU2 t=28C fan=40%, GPU3 t=27C fan=40%, GPU4 t=33C fan=42%, GPU5 t=32C fan=41%
ETH: Job timeout, disconnect, retry in 20 sec...

Here's a question:
If my biggest and main problem with mining is heat, whats the best way to lower the heat from GPUs?
Should I use lower clocks, is there a command line which tells the miner to mine slower/less intense...?
I'm willing to sacrifice the hash speed for lower temps.
Thanks!

I am moving to Phoenix too, dual mining becomes unprofitable, miner is unstable, devfee is huge for Claymore.

Is that on one of your rigs or on all of them? have you tried swapping cards to see if it is a faulty card? I would say it is the card because I had a similar effect. For me one card was overclocked/undervolted too much and stalled and as a consequence the watchdog jumped in and restarted the miner...

Since an update to 11.3 only one rig can't create the dag file. - open cl error -48

There are RX480 8gb.

So i test the Version 11.2 again and all works fine.

What can it be?

pre v11, im never getting any incorrect shares dual mining

now, even with 11.4, im getting incorrect shares. i even downclocked mem, increase voltage and fan speeds to no avail, like so noticeable that my hashrate decreased a lot from downclocking. although im not getting any memory errors in hwinfo.

whats up with v11s?

Guys, I´d really appreciate an advice. I run several 6*rx470/480 rigs. Suddenly out of nowhere Claymore miner refused to start, it says:

OpenCL initializing...

01:20:14:573 1698 AMD Cards available: 6
01:20:14:583 1698 GPU #0: Ellesmere (Radeon (TM) RX 480 Graphics), 8192 MB available, 36 compute units (pci bus 1:0:0)
01:20:14:586 1698 GPU #0 recognized as Radeon RX 480/580
01:20:14:590 1698 GPU #1: Ellesmere (Radeon (TM) RX 480 Graphics), 8192 MB available, 36 compute units (pci bus 3:0:0)
01:20:14:595 1698 GPU #1 recognized as Radeon RX 480/580
01:20:14:599 1698 GPU #2: Ellesmere (Radeon (TM) RX 480 Graphics), 8192 MB available, 36 compute units (pci bus 5:0:0)
01:20:14:604 1698 GPU #2 recognized as Radeon RX 480/580
01:20:14:608 1698 GPU #3: Ellesmere (Radeon (TM) RX 480 Graphics), 8192 MB available, 36 compute units (pci bus 6:0:0)
01:20:14:612 1698 GPU #3 recognized as Radeon RX 480/580
01:20:14:618 1698 GPU #4: Ellesmere (Radeon (TM) RX 480 Graphics), 8192 MB available, 36 compute units (pci bus 7:0:0)
01:20:14:622 1698 GPU #4 recognized as Radeon RX 480/580
01:20:14:626 1698 GPU #5: Ellesmere (Radeon (TM) RX 480 Graphics), 8192 MB available, 36 compute units (pci bus 8:0:0)
01:20:14:630 1698 GPU #5 recognized as Radeon RX 480/580
01:20:14:637 1698 POOL/SOLO version
01:20:14:641 1698 Platform: Windows
01:20:14:720 1698 start building OpenCL program for GPU 0...

...and it hangs forever. After several restarts it may start working for a while, but sooner or later GPU0 (always gpu0) drops to 0,00 mhs and rig freezes.

ETH: job changed
01:18:27:078 190c new buf size: 0
01:18:27:084 190c ETH: 03/13/18-01:18:27 - New job from daggerhashimoto.eu.nicehash.com:3353
01:18:27:088 190c target: 0x00000001fffe0000 (diff: 2147MH), epoch 174(2.36GB)
01:18:27:093 190c ETH - Total Speed: 142.653 Mh/s, Total Shares: 7, Rejected: 0, Time: 00:02
01:18:27:098 190c ETH: GPU0 0.000 Mh/s, GPU1 28.468 Mh/s, GPU2 28.465 Mh/s, GPU3 28.449 Mh/s, GPU4 28.289 Mh/s, GPU5 28.982 Mh/s
01:18:31:640 1934 checked ETH share on CPU, spent 5ms

I tried different drivers, claymore versions (currently using V11.0), installed a HDMI plug on that card, reset OC to default settings. When I disable GPU0 from "device manager", miner starts working without any problems... so only disabling helps. And that´s on 4 out of 6 rigs. Any clues/ideas? Thanks a lot and sorry for such a long message.

 

Or use Linux instead of Windows! 

You can dload from Google. Just right click it and copy to your drive (Google). Then it let's you dload if you make a copy of that on your drive. You still have to stop windows deleting it though.

love the program and have used it for a months.. why you gotta package it in a way that everything thinks its a virus lol

i download it from mega, chrome says no... cant download from google cause they say no, finally download with microsoft edge, windows says no instead, finally add rule to protection to skip folder.. IT works yay

It is running stable and with good hash rate at my Nvidia rig (6x). Linux here.

Try this:

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

EthDcrMiner64.exe -epool us1.ethermine.org:14444 -ewal 0xfe943a6dabf68375754d07044812f76a0dd01d64 -epsw x -di 0



CONFIGURATION FILE

You can use "config.txt" file instead of specifying options in command line.
If there are not any command line options, miner will check "config.txt" file for options.
If there is only one option in the command line, it must be configuration file name.
If there are two or more options in the command line, miner will take all options from the command line, not from configuration file.

For me too. I have tried to use any 11.x version, but all of them have strange hashrate. It is less then in 10.6. So I rolled back again to 10.6 (

Guys,

Which is the best ETH mining pool?

I'm using Suprnova but I don't know if it is good or if I should change to another one...

Thanks

Yeah, it's still reading all cards. I don't get  it.

Seems to have done it. Thanks again.

If you're using 11.3 or 11.4 the devfee connection still goes to the secure ssl port 5555, even though you may have set it up to use the non secure
port 4444 connection for mining. That's what I see in the logs. Changing to the 4444 port should not help anyone's situation as far as I can tell if
you're using .3 or .4 versions. If I'm wrong please let me know.

https://medium.com/@bitfly/ethermine-stratum-security-upgrade-d2245076e1b5

use ssl://eu1.ethermine.org:5555 for example.Reliable SSL server

Single mining.