Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 444. (Read 6590718 times)
February 03, 2018, 04:20:12 PM
anyone who dual mining could share the command line they use?
February 03, 2018, 03:28:41 PM
I finally have a stable system with a good hashrate.
Any ideas to make it even better? With more hashrate or the same with lower temps?
GPU0 (Bios from https://anorak.tech)
Gigabyte RX 570 Gaming
Core 1190
Memory 2110
GPU1 (Bios from https://anorak.tech)
Gigabyte RX 570 Aurus
Core 1210
Memory 2080
GPU2
Palit 1070 JetStream
Power Limit 70
Core -200
Memory +780
Any ideas to make it even better? With more hashrate or the same with lower temps?
GPU0 (Bios from https://anorak.tech)
Gigabyte RX 570 Gaming
Core 1190
Memory 2110
GPU1 (Bios from https://anorak.tech)
Gigabyte RX 570 Aurus
Core 1210
Memory 2080
GPU2
Palit 1070 JetStream
Power Limit 70
Core -200
Memory +780
February 03, 2018, 03:21:49 PM
RX 580 8G, Hynix memory (2225 MHz IIRC). I'm pretty happy with the speed, yeah. I reach 31.6 MH/s per card with a clock of 2250 MHz but shit happens from time to time (although my memory errors appear to be very very very low).
Care to share your config file (memory and core speeds and voltages) ?
What's your per gpu consumption?
900 mV for everything
Power consumption between 850 and 950 W for the whole rig (6 cards)
February 03, 2018, 03:18:42 PM
I have unusual situation: my PSU made much noise in ETH mode only. So, I have to continue with dual mining in order to reduce the noise. Stupid situation, but can't do nothing.
Strange situation at all, probably for some reason in ETH mode your setup is consuming more power from PSU. I tried with my rigs and the only way to do that is when I’m using stock config of my GPUs and the power consumption is higher.
[/quote]
He did not specify what kind of noise his PSU emits - is it fan noise or coil whine. Coil whine can actually be much more audible at lower power load.
February 03, 2018, 03:11:48 PM
hi folks,
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2, 16.10.3 15.12, 18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup
1. You are risking to brick the GPU by flashing a downloaded BIOS image. Just move the 1500 or custom timing to 1750 to 2000 straps and overclock manually by MSI Afterburner or OverDriveNTool.i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2, 16.10.3 15.12, 18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup
2. How many GPUs do you have and what's your MOBO? If 4+ GPUs, have you enabled Above 4G Decoding/Mining Mode? Above 4G Decoding works only in UEFI environment<>Windows installation must be UEFI as well.
3. You were getting low hashrate because none of 15.x-16.x drivers have the DAG fix (you are attempting to mine ETH or ETC, performance of both affected by DAG size) and the DAG fix was not activated in 18.2. I'd go with AMD 17.12.1 driver, it seems stable and enable Compute Workload for all GPUs (AMD Preferences>Settings>General>Gaming>select Compute Workload).
February 03, 2018, 03:06:21 PM
Is there an solution, so that wattman will not reset the settings ?
I have not overclocked, some cards will set at a less gpu clock, to keep the temp lower,
But sometime wattman crashes and reset all and then overheats my room :-)
minersoftware will not crash only wattmann,
There is also a new AMD driver available 18.2.1, hope it is better,
Got 2 rigs with 12 AMD R9 390 and the consume much and also produce much heat
I have not overclocked, some cards will set at a less gpu clock, to keep the temp lower,
But sometime wattman crashes and reset all and then overheats my room :-)
minersoftware will not crash only wattmann,
There is also a new AMD driver available 18.2.1, hope it is better,
Got 2 rigs with 12 AMD R9 390 and the consume much and also produce much heat
February 03, 2018, 03:04:17 PM
Wait for claymore until he releases new algos for new coins.....
When it's can be released?
I have unusual situation: my PSU made much noise in ETH mode only. So, I have to continue with dual mining in order to reduce the noise. Stupid situation, but can't do nothing.
Strange situation at all, probably for some reason in ETH mode your setup is consuming more power from PSU. I tried with my rigs and the only way to do that is when I’m using stock config of my GPUs and the power consumption is higher.
February 03, 2018, 02:58:16 PM
Hello there 
I have 1 rig with 7x rx 570 4gb Nitro Sapphire + and i am using Claymore for mining only ETH
But i am geting it crash every day few times per day
http://prntscr.com/i9os7n This is hashrate i get it from them and GPU temp.
I have 1 rig with 7x rx 570 4gb Nitro Sapphire + and i am using Claymore for mining only ETH
But i am geting it crash every day few times per day
http://prntscr.com/i9os7n This is hashrate i get it from them and GPU temp.
Are you using different configs for each card? Probably one of them need to have a lower clock. Checking the memory error will provide a clue.., use HWINFO to do that.
February 03, 2018, 02:55:51 PM
hi folks,
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2, 16.10.3 15.12, 18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2, 16.10.3 15.12, 18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup
Did you try mclocks around 2050, 2080 or 2100? And cclock 1100, 1125 or 1150? And mvddc 900 or 950?
If you already tried Blockchain drivers Aug 23, probably you need to put more clock to achive better rates.
To he configured stick in the GPUs, open the claymore miner, waits until the last setting dag file, close the miner and repeat 2-3 times this process.
February 03, 2018, 02:47:04 PM
Hello there
I have 1 rig with 7x rx 570 4gb Nitro Sapphire + and i am using Claymore for mining only ETH
But i am geting it crash every day few times per day
http://prntscr.com/i9os7n This is hashrate i get it from them and GPU temp.
I have 1 rig with 7x rx 570 4gb Nitro Sapphire + and i am using Claymore for mining only ETH
But i am geting it crash every day few times per day
http://prntscr.com/i9os7n This is hashrate i get it from them and GPU temp.
February 03, 2018, 02:43:23 PM
RX 580 8G, Hynix memory (2225 MHz IIRC). I'm pretty happy with the speed, yeah. I reach 31.6 MH/s per card with a clock of 2250 MHz but shit happens from time to time (although my memory errors appear to be very very very low).
Care to share your config file (memory and core speeds and voltages) ?
What's your per gpu consumption?
February 03, 2018, 01:23:00 PM
hi folks,
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2, 16.10.3 15.12, 18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup
i'm wondering if sombody could help me out with my MSI rx 480 4gb gaming x hynix memory rig.
i'm only getting max. 21mh/s with a modded bios timing strap from 1500 to 2000, core clock gives me no difference, memclock 1900 gives me 19-20 mh/s and memclock to 2000 gives me 21.3 mh/s.
other timing straps gives me even more less..
at the wall i'm getting +- 140 watt each card.
since yesterday my computer even refuse to instal my cards. i already have multiple times deleted the drivers with ddu.
i'm using windows 10 and have try driver 16.9.2, 16.10.3 15.12, 18.2 all off the drivers only work with one card but when i plug them in all togheter they dont work, only the first time that i installed everything they all worked and where able to mine but only with 20.7 mh/s. my risers are all fine and already have try new risers and a new clean windows 10 also. but nothing works :s
when i plug everything in ,the fans are blowing normal but when i log in the drivers keep repeating to install my screen keeps flickering, like the cards are keep trying to install but it always fail.
hope sombody can give me some other suggestions that i can try.
trying to flash the original bios to see if that works is going to be difficult because i lost it..
i have found a rom the rom that i have flashed on techpowerup
February 03, 2018, 10:09:44 AM
RX 580 8G, Hynix memory (2225 MHz IIRC). I'm pretty happy with the speed, yeah. I reach 31.6 MH/s per card with a clock of 2250 MHz but shit happens from time to time (although my memory errors appear to be very very very low).
From FAQ/Readme/OP:
- Miner freezes if I put cursor to its window in Windows 10 until any key is pressed. Sometimes miner freezes randomly until any key is pressed.
You should make some changes in Windows:
https://superuser.com/questions/555160/windows-command-prompt-freezing-on-focus
https://superuser.com/questions/419717/windows-command-prompt-freezing-randomly?rq=1
https://superuser.com/questions/1051821/command-prompt-random-pause?rq=1
Thanks a lot.
Woke up this morning (at 11:30 
) with a non-functioning rig.
Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
What do you reckon? How can I prevent that?
) with a non-functioning rig.Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
What do you reckon? How can I prevent that?
From FAQ/Readme/OP:
- Miner freezes if I put cursor to its window in Windows 10 until any key is pressed. Sometimes miner freezes randomly until any key is pressed.
You should make some changes in Windows:
https://superuser.com/questions/555160/windows-command-prompt-freezing-on-focus
https://superuser.com/questions/419717/windows-command-prompt-freezing-randomly?rq=1
https://superuser.com/questions/1051821/command-prompt-random-pause?rq=1
February 03, 2018, 09:30:41 AM
Woke up this morning (at 11:30 ) with a non-functioning rig.
Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
What do you reckon? How can I prevent that?
) with a non-functioning rig.Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
What do you reckon? How can I prevent that?
These are some sick speeds there bro. What cards are you running?
February 03, 2018, 09:24:18 AM
Woke up this morning (at 11:30 ) with a non-functioning rig.
Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
What do you reckon? How can I prevent that?
) with a non-functioning rig.Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
What do you reckon? How can I prevent that?
From FAQ/Readme/OP:
- Miner freezes if I put cursor to its window in Windows 10 until any key is pressed. Sometimes miner freezes randomly until any key is pressed.
You should make some changes in Windows:
https://superuser.com/questions/555160/windows-command-prompt-freezing-on-focus
https://superuser.com/questions/419717/windows-command-prompt-freezing-randomly?rq=1
https://superuser.com/questions/1051821/command-prompt-random-pause?rq=1
February 03, 2018, 08:17:30 AM
Woke up this morning (at 11:30 ) with a non-functioning rig.
Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
https://image.ibb.co/ejVyb6/Screenshot_20180203_113017.png
What do you reckon? How can I prevent that?
) with a non-functioning rig.Weirdly, Claymore's was running with no error, no watchdog shenanigans. But if you look at the last timestamps from Claymore's and the system time, you see there's quite a mismatch:
https://image.ibb.co/ejVyb6/Screenshot_20180203_113017.png
What do you reckon? How can I prevent that?
February 03, 2018, 08:12:01 AM
You are cross posting to many threads which is considered spam. Your account should be banned. It is not relevant. It is spam when you post to so many threads.
I simply posted to the relevant threads. My software simply supports a lot of stuff making a lot of threads relevant.
Didn't mean to spam, I'm sorry if it looked like it.
When I see the same post over and over in many of the threads I subscribe to it is spam by definition. You should not have posted to other people's threads. This is considered bad forum manners. You should have created your own new thread in the mining sub forum and described your software and what it does. Then people can discuss your software instead of being annoyed seeing your post over and over in other software's forum. I suggest you delete all the posts and create your own thread. That is how the forum should operate.
February 03, 2018, 07:32:54 AM
Hello
i recently switched all my GTX 1070/1070ti to ETH due to ZEC price drops etc.
I find some rigs work ok (stable) and on some the hashrate is fluctuating.
may this be realted to drivers? are there drivers ok ?
385.41 for 6x1070 rigs
and 388.59 fo 6x1070ti rigs? or claymore requires the newest nvidia drivers?
i use v10.5 version.... the HASHRATE is ok at the start, but then after some time fluctuates. I check on nanopool for 6hr average and find some rigs only have 170 MH/s avg.
settings differ cause i try...
1070: power 75 (high but i want stability, not really low power), core -200 (some -190 now), mem +680 (some +690). the rigs are very cool temps around 38-42 deg.
i put -r 120 so the client restarts (i find this give better hash?)
MY RX580 rigs are 100% stable there is no fluctiation but nvidia with ETH gives me headache plz help ;-)
ETH: 02/03/18-13:29:46 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 191.148 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:22
ETH: GPU0 31.876 Mh/s, GPU1 31.869 Mh/s, GPU2 31.899 Mh/s, GPU3 31.850 Mh/s, GPU4 31.756 Mh/s, GPU5 31.900 Mh/s
ETH: 02/03/18-13:30:11 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 184.847 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:22
ETH: GPU0 31.192 Mh/s, GPU1 29.779 Mh/s, GPU2 31.177 Mh/s, GPU3 30.376 Mh/s, GPU4 31.250 Mh/s, GPU5 31.073 Mh/s
GPU0 t=39C fan=69%, GPU1 t=42C fan=69%, GPU2 t=41C fan=69%, GPU3 t=38C fan=69%, GPU4 t=32C fan=69%, GPU5 t=48C fan=69%
ETH: 02/03/18-13:30:27 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 174.012 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 23.557 Mh/s, GPU1 30.301 Mh/s, GPU2 30.699 Mh/s, GPU3 30.942 Mh/s, GPU4 30.857 Mh/s, GPU5 27.655 Mh/s
ETH: 02/03/18-13:30:35 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 146.193 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 22.078 Mh/s, GPU1 22.095 Mh/s, GPU2 31.022 Mh/s, GPU3 22.006 Mh/s, GPU4 26.825 Mh/s, GPU5 22.167 Mh/s
ETH: 02/03/18-13:30:43 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 189.880 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.674 Mh/s, GPU1 31.843 Mh/s, GPU2 31.833 Mh/s, GPU3 31.756 Mh/s, GPU4 31.142 Mh/s, GPU5 31.633 Mh/s
GPU0 t=39C fan=69%, GPU1 t=43C fan=69%, GPU2 t=43C fan=69%, GPU3 t=38C fan=69%, GPU4 t=32C fan=69%, GPU5 t=48C fan=69%
ETH: 02/03/18-13:30:50 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 191.070 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.879 Mh/s, GPU1 31.858 Mh/s, GPU2 31.790 Mh/s, GPU3 31.868 Mh/s, GPU4 31.859 Mh/s, GPU5 31.816 Mh/s
ETH: 02/03/18-13:30:51 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 190.558 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.838 Mh/s, GPU1 31.822 Mh/s, GPU2 31.588 Mh/s, GPU3 31.853 Mh/s, GPU4 31.816 Mh/s, GPU5 31.641 Mh/s
ETH: 02/03/18-13:31:12 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 189.109 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.362 Mh/s, GPU1 31.209 Mh/s, GPU2 31.028 Mh/s, GPU3 31.851 Mh/s, GPU4 31.836 Mh/s, GPU5 31.823 Mh/s
i recently switched all my GTX 1070/1070ti to ETH due to ZEC price drops etc.
I find some rigs work ok (stable) and on some the hashrate is fluctuating.
may this be realted to drivers? are there drivers ok ?
385.41 for 6x1070 rigs
and 388.59 fo 6x1070ti rigs? or claymore requires the newest nvidia drivers?
i use v10.5 version.... the HASHRATE is ok at the start, but then after some time fluctuates. I check on nanopool for 6hr average and find some rigs only have 170 MH/s avg.
settings differ cause i try...
1070: power 75 (high but i want stability, not really low power), core -200 (some -190 now), mem +680 (some +690). the rigs are very cool temps around 38-42 deg.
i put -r 120 so the client restarts (i find this give better hash?)
MY RX580 rigs are 100% stable there is no fluctiation but nvidia with ETH gives me headache plz help ;-)
ETH: 02/03/18-13:29:46 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 191.148 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:22
ETH: GPU0 31.876 Mh/s, GPU1 31.869 Mh/s, GPU2 31.899 Mh/s, GPU3 31.850 Mh/s, GPU4 31.756 Mh/s, GPU5 31.900 Mh/s
ETH: 02/03/18-13:30:11 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 184.847 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:22
ETH: GPU0 31.192 Mh/s, GPU1 29.779 Mh/s, GPU2 31.177 Mh/s, GPU3 30.376 Mh/s, GPU4 31.250 Mh/s, GPU5 31.073 Mh/s
GPU0 t=39C fan=69%, GPU1 t=42C fan=69%, GPU2 t=41C fan=69%, GPU3 t=38C fan=69%, GPU4 t=32C fan=69%, GPU5 t=48C fan=69%
ETH: 02/03/18-13:30:27 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 174.012 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 23.557 Mh/s, GPU1 30.301 Mh/s, GPU2 30.699 Mh/s, GPU3 30.942 Mh/s, GPU4 30.857 Mh/s, GPU5 27.655 Mh/s
ETH: 02/03/18-13:30:35 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 146.193 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 22.078 Mh/s, GPU1 22.095 Mh/s, GPU2 31.022 Mh/s, GPU3 22.006 Mh/s, GPU4 26.825 Mh/s, GPU5 22.167 Mh/s
ETH: 02/03/18-13:30:43 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 189.880 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.674 Mh/s, GPU1 31.843 Mh/s, GPU2 31.833 Mh/s, GPU3 31.756 Mh/s, GPU4 31.142 Mh/s, GPU5 31.633 Mh/s
GPU0 t=39C fan=69%, GPU1 t=43C fan=69%, GPU2 t=43C fan=69%, GPU3 t=38C fan=69%, GPU4 t=32C fan=69%, GPU5 t=48C fan=69%
ETH: 02/03/18-13:30:50 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 191.070 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.879 Mh/s, GPU1 31.858 Mh/s, GPU2 31.790 Mh/s, GPU3 31.868 Mh/s, GPU4 31.859 Mh/s, GPU5 31.816 Mh/s
ETH: 02/03/18-13:30:51 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 190.558 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.838 Mh/s, GPU1 31.822 Mh/s, GPU2 31.588 Mh/s, GPU3 31.853 Mh/s, GPU4 31.816 Mh/s, GPU5 31.641 Mh/s
ETH: 02/03/18-13:31:12 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 189.109 Mh/s, Total Shares: 87, Rejected: 0, Time: 01:23
ETH: GPU0 31.362 Mh/s, GPU1 31.209 Mh/s, GPU2 31.028 Mh/s, GPU3 31.851 Mh/s, GPU4 31.836 Mh/s, GPU5 31.823 Mh/s
February 03, 2018, 07:17:45 AM
For those mining using:
If you are using proprietary AMD's driver amdgpu-pro driver you might have noticed the hash rate is not stable and dropped. This is due to that Security Issue found on Intel chips recently.
I know the solution is to disable automatic updates of the kernel and to "roll back" to previously "good working" (for mining) Linux Kernel Version.
What I would like to know is what version of the Linux Kernel (4.4.xx or 4.10.xx or 4.13.xx) you found to be more stable and optimized for mining?
Is it the normal version or the HWE version?
P.S.: if your rig is still stable you can get this info by typing: uname -a
- Linux Ubuntu Server 16.04
- GPU RX580
If you are using proprietary AMD's driver amdgpu-pro driver you might have noticed the hash rate is not stable and dropped. This is due to that Security Issue found on Intel chips recently.
I know the solution is to disable automatic updates of the kernel and to "roll back" to previously "good working" (for mining) Linux Kernel Version.
What I would like to know is what version of the Linux Kernel (4.4.xx or 4.10.xx or 4.13.xx) you found to be more stable and optimized for mining?
Is it the normal version or the HWE version?
P.S.: if your rig is still stable you can get this info by typing: uname -a
February 03, 2018, 06:34:03 AM
When v10.2 added " now miner supports up to #299 epoch.", what's the highest DAG supported by previous versions? Does anyone know? I've got a stable setup with v10.1, I'd rather not update until absolutely necessary.
Previous versions support up to #199 epoch.
Thanks!
Jump to: