Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 461.

fpontilho

newbie

Activity: 8

Merit: 0

Quote from: fpontilho on January 24, 2018, 01:17:08 AM

I'm mining with those RX470 8GB Mining Edition - Ellesmere

I switched on simplemining to the version 10.5 hopping that dualmining wouldn't decrease my ETH hashrates, but the hashrate for ETH goes from 26/27mh/s down to 18/20 dualmining SIACOIN.

Question is, I haven't installed any driver, using whatever version Claymore's 10.5 is running these cards on, should I run Catalyst (Crimson) 15.12 ? If that is so, can you give me a hand on HOW to do that on Claymore, because I don't have windows on those rigs.

If you'd read the first post (instead of quoting it), you'd see you can set dcri. Try setting -dcri 1 and see if your Eth goes up. From that point on you can increase -dcri value with + / - in the miner console to tweak the balance between ETH/SIA.

You are completly right.. I was a lazy SON OF A @(#*@...

Thanks for the help.. It worked...

007Bul

newbie

Activity: 16

Merit: 0

Quote from: KleinerMiner on January 24, 2018, 03:24:19 AM

Hi!

Is it possible to use the "-r Restart miner mode" Option even when are no Cards have issues?
I would like to have the miner stopped after a defined period of time (e.g. 12 hours) and to restart/switch to a other coin/walletwallet for 12 hours and then again Switch back.

So at the end i´m looking/asking for a coin/wallet switching possibility in a chosen timeframe.

thanks!

Don't know, but I used to place an Arduino and a relay on the on/pff switch.
I had some problems with the machine running stable and put a temperature sensor on the Arduino. When the temp was low (because the cards generate some heat) I let it press the on/off switch for 10 seconds. Stop 1 minuten. Put switch again on for 1 second. Wait 10 minutes (because a new start should warm up the cards) and then wait for the whole process.

You can put a timer on it.
May be something like this.https://www.youtube.com/watch?v=saKqxqGffz4

pubix

member

Activity: 154

Merit: 10

Will dual mining still be a thing now that ASICs are comming for SIA/DCR?

KleinerMiner

newbie

Activity: 20

Merit: 0

Hi!

Is it possible to use the "-r Restart miner mode" Option even when are no Cards have issues?
I would like to have the miner stopped after a defined period of time (e.g. 12 hours) and to restart/switch to a other coin/walletwallet for 12 hours and then again Switch back.

So at the end i´m looking/asking for a coin/wallet switching possibility in a chosen timeframe.

thanks!

kkourmousis

member

Activity: 119

Merit: 10

@fpontilho Don't you think that quoting a page-long post is a bit... too much?

If you really have to refer to the original post, you can do something like

"as the original post says"

and maybe even quote the specific part of the post that you are referring to...

fpontilho

newbie

Activity: 8

Merit: 0

igotfits

full member

Activity: 298

Merit: 100

Quote from: igotfits on January 24, 2018, 12:27:50 AM

21:06:07:808 1c6c NVML: cannot get current temperature, error 999 (an internal driver error occurred)
21:06:07:808 1c6c NVML: cannot get fan speed, error 999 (an internal driver error occurred)

Help?

I added a new card and just forgot to switch over to compute mode, that should fix the issue?

igotfits

full member

Activity: 298

Merit: 100

21:06:07:808 1c6c NVML: cannot get current temperature, error 999 (an internal driver error occurred)
21:06:07:808 1c6c NVML: cannot get fan speed, error 999 (an internal driver error occurred)

Help?

Biodom

legendary

Activity: 3892

Merit: 4331

TL;DR Anybody has an opinion about Adrenalin 17 vs 18 (Jan 18) drivers on win10 and Vega? Which one is better or are they the same?

I cannot use the blockchain driver because it causes some kind of weird conflict between cards and everything is pixelated on screen.
tried patch program to no avail.

Adrenalin 17 sucks even in compute mode as it reduces mining about 8-9% comparing with blockchain driver on Vegas (470/580 stay the same).

007Bul

newbie

Activity: 16

Merit: 0

Quote from: Faboo005 on January 23, 2018, 03:34:55 PM

Quote from: 007Bul on January 23, 2018, 03:31:20 PM

Today I put my mining rig back in action. Had stopped 4 years ago because the housing agency came by with the police because they where thinking that it was a cannabis plant

.

I use the SAPPHIRE R9 290 Tri-X 4GB card. I'd remember I had 800-900 Mh's speed per card. Today, with a fresh install I downloaded Claymores miner and try to mine PIRL.
My speed now is only 28Mh's.
Is this because of a different script, or am I missing something.

Hope you can help me

You were not getting 800mhs. You'd have been earning $75 per day on each card. You either read it wrong or misremembered.

It was a bit like this,

https://www.youtube.com/watch?v=lfvzoDlQP7s

doorcollider

newbie

Activity: 4

Merit: 0

Quote from: muzuca on January 22, 2018, 07:17:07 PM

Quote from: doorcollider on January 22, 2018, 05:16:18 PM

Hello,

my pc freezez or one random gpu hashrate reports 0 mh/s when i use claymore undervoltage commands and clock with my rx 580 nitro + in dual mine eth+pasc. My hash rates are 30mh/s/gpu. Any of you have this problem? If so do you have any suggestion? Here is my .bat file.

TIMEOUT 40
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0x0200BA73CA49Aa286570588A055396bc0C0d4087.rig1/[email protected] -epsw x -dpool stratum+tcp://pasc-eu1.nanopool.org:15555 -dwal 274485-29.0.rig1/[email protected] -dpsw x -dcoin pasc -dcri 10 -mode 0 -tstop 85 -tt 65 -fanmin 70 -fanmax 100 -cclock 1130 -mclock 2150 -cvddc 875 -mvddc 875 -ftime 10

Try different config for each card, they aren’t equal... a good config for RX 580 is: 1150, 2150 with 900 of voltage. But I have 2 cards that I need to lower the mclock to 2135 and the voltage 950, otherwise they hangs.

and how do i know on what gpu should i put different config? all of them are sapphire rx 580 nitro + with samsung memories.

sstativa

newbie

Activity: 2

Merit: 0

Quote from: HarryTheHarry on January 23, 2018, 04:07:53 PM

Quote from: HarryTheHarry on January 23, 2018, 11:13:02 AM

Quote from: ?? on ??

Quote from: HarryTheHarry on January 23, 2018, 09:28:52 AM

Quote from: ?? on ??

Quote from: HarryTheHarry on January 23, 2018, 06:19:14 AM

dear all,

currently im running ubuntu 16.04 lts rig, with 3x rx 580. the problem is ethash rate on dual mining (solo as well). on modded bios cards i hardly squeeze 21mh.
no matter what are the mclock/cclock values hashing varies 18-21mh/s. those values are reachble only wits asm 2 mode, solo eth mining does not help here. i really wasted lots o time no significant improve.
however at zec mining i got 330+hs per gpu which is oustanding, but what the heck can i do with eth?

What RAM brand do you have and what memory straps did you flash?

I remember when flashing UBER 3.1 timing on my samsung memory my hashrate went down vs the 1750 timings

i got xfx with samsung, which i managed to flash 1:1500 ^ and 2:1500 ^
2x sappphiro with micron first 1:1650 ^ and second 1:1750 ^

Quote from: rusan on January 23, 2018, 06:29:29 AM

Quote from: HarryTheHarry on January 23, 2018, 06:19:14 AM

I had same problem on linux. And it was new core and need to reinstall drivers.

what you mean by new core? as per drivers i have recomended amdgpu-pro-17.40-483984, which were reinstalled already couple of times

What if you try to revert the flash to 1:1750? and see if the hashrate increases?

i tried without flashed bioses and results are slightly worse than now ;/

I have updated claymore to v10.5 gained ~2mhs, but that still sux, check this out
https://imgur.com/a/XjW47
other option in exec line -dcoin sc -mode 0 -dcri 10 -fanmin 45 -tstop 84 -tt 65,60,60 -ttli 80 -fanmin 55 -fanmax 95 -cvddc 880 -mvddc 880 -cclock 1130 -mclock 2240 -powlim -15 -logfile mine_ETHSIA_noappend

This params "-cvddc 880 -mvddc 880 -cclock 1130 -mclock 2240" have no effect on Linux OS. You have to use Windows to be able to use them.
If you want to mine on Linux the best solution for you will be to reflash BIOS.

HarryTheHarry

newbie

Activity: 9

Merit: 0

Quote from: HarryTheHarry on January 23, 2018, 11:13:02 AM

Quote from: ?? on ??

Quote from: HarryTheHarry on January 23, 2018, 09:28:52 AM

Quote from: ?? on ??

Quote from: HarryTheHarry on January 23, 2018, 06:19:14 AM

dear all,

currently im running ubuntu 16.04 lts rig, with 3x rx 580. the problem is ethash rate on dual mining (solo as well). on modded bios cards i hardly squeeze 21mh.
no matter what are the mclock/cclock values hashing varies 18-21mh/s. those values are reachble only wits asm 2 mode, solo eth mining does not help here. i really wasted lots o time no significant improve.
however at zec mining i got 330+hs per gpu which is oustanding, but what the heck can i do with eth?

What RAM brand do you have and what memory straps did you flash?

I remember when flashing UBER 3.1 timing on my samsung memory my hashrate went down vs the 1750 timings

i got xfx with samsung, which i managed to flash 1:1500 ^ and 2:1500 ^
2x sappphiro with micron first 1:1650 ^ and second 1:1750 ^

Quote from: rusan on January 23, 2018, 06:29:29 AM

Quote from: HarryTheHarry on January 23, 2018, 06:19:14 AM

I had same problem on linux. And it was new core and need to reinstall drivers.

what you mean by new core? as per drivers i have recomended amdgpu-pro-17.40-483984, which were reinstalled already couple of times

What if you try to revert the flash to 1:1750? and see if the hashrate increases?

i tried without flashed bioses and results are slightly worse than now ;/

I have updated claymore to v10.5 gained ~2mhs, but that still sux, check this out
https://imgur.com/a/XjW47
other option in exec line -dcoin sc -mode 0 -dcri 10 -fanmin 45 -tstop 84 -tt 65,60,60 -ttli 80 -fanmin 55 -fanmax 95 -cvddc 880 -mvddc 880 -cclock 1130 -mclock 2240 -powlim -15 -logfile mine_ETHSIA_noappend

HELIUM_COIN

newbie

Activity: 17

Merit: 0

Hello, thank you so much for all your hard work on this project!

I have a question about under-volting dropouts:

Let's say claymore starts and with undervoltage settings from overdriventool GPU only voltage is 80watts. All is well for a few minutes, then suddenly,the voltage spikes to roof @ 112watts.

What is the best way to avoid this issue? I assume the card wants more voltage when this happens, but it happens even if much higher voltage is given.

Does wattman hold unvervolting better?

I assume the claymore power + - commands would simply throttle the hashrate as well? Which is not really useful... or is anyone using them with success with AMD cards? (voltage at wall proof?)

On certain cards, undervolting can be annoying and problematic to say the least.

I believe proper straps have been used in bios mods.

Thanks for any tips or advice, been trying every trick I can to save power and sustain maximized hashrate!

Cheers to the fellow miners! : )

7anonminer7

newbie

Activity: 15

Merit: 0

Does anyone experience random (in time periods) total system freezes on Claymore 10.3 on Win 10 x64 (Aug 23 blockchain drivers with 3 x RX570 and 1 RX470)?
So only reboot via mobo helps.

So far the most I got it running without freezes is 48 hours, but it can freeze in 2 hours or 10 or x hours.
There's nothing in Claymore or Windows logs.

I've experienced exactly the same behavoir when mining XMR with Claymore's Cryptonote AMD Miner v11 - but not on v9 or v10 - they were quite stable.
My cards are BIOS moded, overclocked in memory, downclocked in core and core voltage - last few days I'm bringing each card 20 MHz down after another freeze trying to understand if it could be related to memory - so far got to 1960 MHz.
However, I think if it was to do with memory - I'd get memory errors (which I don't) and/or general GPU drivers failure or single/multiple GPUs hashing stops - but it just freezes whole system. Quite frustrating tbh.

Btw I have 32G of page file, so virtual memory shouldn't be the cause.
I could try Claymore dual miner v10.5, but something tells me the freezes won't go away :/

Faboo005

newbie

Activity: 46

Merit: 0

Quote from: 007Bul on January 23, 2018, 03:31:20 PM

Today I put my mining rig back in action. Had stopped 4 years ago because the housing agency came by with the police because they where thinking that it was a cannabis plant

.

I use the SAPPHIRE R9 290 Tri-X 4GB card. I'd remember I had 800-900 Mh's speed per card. Today, with a fresh install I downloaded Claymores miner and try to mine PIRL.
My speed now is only 28Mh's.
Is this because of a different script, or am I missing something.

Hope you can help me

You were not getting 800mhs. You'd have been earning $75 per day on each card. You either read it wrong or misremembered.

007Bul

newbie

Activity: 16

Merit: 0

Today I put my mining rig back in action. Had stopped 4 years ago because the housing agency came by with the police because they where thinking that it was a cannabis plant

.

I use the SAPPHIRE R9 290 Tri-X 4GB card. I'd remember I had 800-900 Mh's speed per card. Today, with a fresh install I downloaded Claymores miner and try to mine PIRL.
My speed now is only 28Mh's.
Is this because of a different script, or am I missing something.

Hope you can help me

Matias

full member

Activity: 182

Merit: 101

Quote from: oubba37 on January 22, 2018, 08:45:04 PM

hello i am new in the mining
can i minne with my pc win32
i can't get the clymore for win32
can you help

I think that all miners are for 64 bit systems..

whoismoses

member

Activity: 247

Merit: 59

Quote from: preda on January 23, 2018, 12:08:37 PM

What -gser 2 does?

-gser this setting can improve stability on multi-GPU systems if miner hangs during startup. It serializes GPUs initalization routines. Use "-gser 1" to serailize some of routines and "-gser 2" to serialize all routines.
Using values higher than 2 allows you also to set custom delay between DAG generation on GPUs, for example, "-gser 5" means same as "-gser 2" and also adds 3sec delay between DAG generation (can be useful for buggy drivers and/or weak PSU).
Default value is "0" (no serialization, fast initialization).

7anonminer7

newbie

Activity: 15

Merit: 0

Quote from: ?? on ??

Quote from: 7anonminer7 on January 23, 2018, 10:40:10 AM

Using Claymore 10.3 on Win 10 x64, Aug 23 blockchain drivers with 3 x RX570 and 1 RX470. The problem I'm facing is miner's watchdog doesnt seem to be working - when one (or multiple) GPU gets "GPUx hangs in OpenCL call" error - the miner just stops working - until I hit "s" on keyboard, then and only then it restarts.

This is quite frustrating. Watchdog is enabled (-wd 1) - it even says so when miner launches, also "-r 15" is set. Any idea/solution to this? Thanks.

-wd 1 is default, so you don't need to add it.

Do you have the quick edit functionality disabled? The WD used to hang for me when you are in quickedit mode in the CMD prompt.

You don't really need -r 15 then.

Yeah, I know -wd 1 is default, just had to mention it's 100% enabled.

Actually I had "quickedit mode" enabled, now I've disabled it. When you're saying "WD used to hang" - do you mean it worked, but the miner was hanging/freezing when being restarted by WD or WD wasn't performing any kind of action until button was pressed (like in my case)? Thx for the tip though.

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 461. (Read 6590718 times)