Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 919.

TheLAWNoob

member

Activity: 92

Merit: 10

Anyone have RX 570 or 580?

AMD's newest driver only support 5 cards, BSOD on the 6th. I tried 6 470s same problem.

Have anyone had any luck getting 6 RX 570 or 580 working on Windows 10? I'm not sure if the older drivers will let me install.

manotroll

sr. member

Activity: 305

Merit: 250

What are the parameters to control the intensity of the decred ?
Currently it is possible to do here 28,800mh / s eth and 850mh / s decred
Rx 480
Is it possible to mine eth in one poll and decred in another?

BioMoh

member

Activity: 103

Merit: 10

Quote from: Claymore on April 26, 2017, 04:14:55 PM

Quote from: BioMoh on April 26, 2017, 03:47:33 PM

@Claymore the latest 9.2 version consume the Eth for the DCR even with lowering the -dcri
in ver 8.1 was getting 31.1MH Eth + 575 MH DCR per card and stable with temp 55~58
now 30.8 MH eth + 450 DCR unstable with 61 ~ 65 TEMP
Please undo the changes

i cannot run the old 8.1 ver cz DCR stopped there

"-asm 0" is for you.

23 MH eth + 295 MH DCR

bro u need a coffee

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

Quote from: BioMoh on April 26, 2017, 03:47:33 PM

@Claymore the latest 9.2 version consume the Eth for the DCR even with lowering the -dcri
in ver 8.1 was getting 31.1MH Eth + 575 MH DCR per card and stable with temp 55~58
now 30.8 MH eth + 450 DCR unstable with 61 ~ 65 TEMP
Please undo the changes

i cannot run the old 8.1 ver cz DCR stopped there

"-asm 0" is for you.

BioMoh

member

Activity: 103

Merit: 10

@Claymore the latest 9.2 version consume the Eth for the DCR even with lowering the -dcri

in ver 8.1 was getting 31.1MH Eth + 575 MH DCR per card and stable with temp 55~58

now 30.8 MH eth + 450 DCR unstable with 61 ~ 65 TEMP

Please undo the changes

i cannot run the old 8.1 ver cz DCR stopped there

ZsZolee

newbie

Activity: 9

Merit: 0

I mined till today to Nicehash, I tried some other coins, but after I switched back I get "No job" error on ETH and on PASC too. What's wrong with these settings?

-epool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353
-ewal BTCADDRESS.RIG
-epsw x
-esm 3
-estale 0
-tstop 75
-dpool stratum+tcp://pascal.eu.nicehash.com:3358
-dwal BTCADDRESS.RIG
-dpsw zrig1
-dcoin pasc
-allpools 1
-mode 0
-wd 1
-r 1

pornluver

hero member

Activity: 960

Merit: 514

Quote from: gerietis on April 26, 2017, 10:00:39 AM

Quote from: golden0707 on April 25, 2017, 04:07:03 AM

Wattage of the PSU is the output ability not input.

that's right, but don't worry, chieftec will blow up soon at such high load

What does it mean

Code:

ETH: GPU0 30.030 Mh/s, GPU1 30.102 Mh/s, GPU2 30.114 Mh/s, GPU3 30.101 Mh/s, GPU4 30.104 Mh/s, GPU5 30.104 Mh/s
ETH: 04/27/17-00:50:59 - New job from europe.ethash-hub.miningpoolhub.com:17020
ETH - Total Speed: 180.177 Mh/s, Total Shares: 426, Rejected: 0, Time: 03:13
ETH: GPU0 30.108 Mh/s, GPU1 30.104 Mh/s, GPU2 30.078 Mh/s, GPU3 29.678 Mh/s, GPU4 30.107 Mh/s, GPU5 30.110 Mh/s
GPU #5 got incorrect share. If you see this warning often, make sure you did not overclock it too much!
GPU0 t=60C fan=71%
ETH: 04/27/17-00:51:21 - New job from europe.ethash-hub.miningpoolhub.com:17020
ETH - Total Speed: 180.590 Mh/s, Total Shares: 426, Rejected: 0, Time: 03:14
ETH: GPU0 30.101 Mh/s, GPU1 30.102 Mh/s, GPU2 30.079 Mh/s, GPU3 30.104 Mh/s, GPU4 30.101 Mh/s, GPU5 30.104 Mh/s
ETH: 04/27/17-00:51:27 - SHARE FOUND - (GPU 2)
ETH: 04/27/17-00:51:27 - SHARE FOUND - (GPU 2)
ETH: Share accepted (172 ms)!
ETH: 04/27/17-00:51:27 - New job from europe.et

In one hand it says I got 426 Total shares rejected 0. The it says GPU 5 got incorrect share. Which one is right?

Also which shares are found and sent to stratum? The 426 shares or the share found - (GPU 2)

Also I can't find

SHARE FOUND - (GPU 5) anywhere. It's as if GPU 5 is always wrong.

Restarting miner seems fix the problem

Actually how many "shares" do I got if logs are like these

Code:

ETH - Total Speed: 180.896 Mh/s, Total Shares: 6, Rejected: 0, Time: 00:03
ETH: GPU0 30.118 Mh/s, GPU1 30.099 Mh/s, GPU2 30.107 Mh/s, GPU3 30.105 Mh/s, GPU4 30.103 Mh/s, GPU5 30.407 Mh/s
ETH: 04/27/17-01:05:17 - SHARE FOUND - (GPU 0)
ETH: Share accepted (296 ms)!
ETH: 04/27/17-01:05:24 - SHARE FOUND - (GPU 5)
ETH: Share accepted (359 ms)!
GPU0 t=58C fan=71%
ETH: 04/27/17-01:05:28 - SHARE FOUND - (GPU 0)
ETH: Share accepted (703 ms)!
ETH: 04/27/17-01:05:30 - SHARE FOUND - (GPU 2)
ETH: Share accepted (281 ms)!
ETH: 04/27/17-01:05:49 - New job from europe.ethash-hub.miningpoolhub.com:17020
ETH - Total Speed: 179.609 Mh/s, Total Shares: 10, Rejected: 0, Time: 00:03
ETH: GPU0 30.100 Mh/s, GPU1 30.104 Mh/s, GPU2 30.103 Mh/s, GPU3 30.093 Mh/s, GPU4 28.793 Mh/s, GPU5 30.416 Mh/s
GPU0 t=59C fan=71%
ETH: 04/27/17-01:06:09 - SHARE FOUND - (GPU 5)
ETH: Share accepted (468 ms)!
ETH: 04/27/17-01:06:15 - New job from europe.ethash-hub.miningpoolhub.com:17020
ETH - Total Speed: 180.809 Mh/s, Total Shares: 11, Rejected: 0, Time: 00:04
ETH: GPU0 30.058 Mh/s, GPU1 30.043 Mh/s, GPU2 30.088 Mh/s, GPU3 30.109 Mh/s, GPU4 30.099 Mh/s, GPU5 30.413 Mh/s
ETH: 04/27/17-01:06:18 - New job from europe.ethash-hub.miningpoolhub.com:17020
ETH - Total Speed: 180.729 Mh/s, Total Shares: 11, Rejected: 0, Time: 00:04
ETH: GPU0 30.103 Mh/s, GPU1 30.051 Mh/s, GPU2 30.087 Mh/s, GPU3 30.000 Mh/s, GPU4 30.095 Mh/s, GPU5 30.393 Mh/s
GPU0 t=59C fan=70%

Basically I got Total Shares: 10 followed by 2-3 SHARE FOUND message. So do I get 10 shares or 2-3 shares? Which one is correct?

gerietis

member

Activity: 100

Merit: 11

Quote from: golden0707 on April 25, 2017, 04:07:03 AM

Wattage of the PSU is the output ability not input.

that's right, but don't worry, chieftec will blow up soon at such high load

EvilC0P

newbie

Activity: 50

Merit: 0

Quote from: rawbot on April 26, 2017, 08:53:05 AM

Quote from: Godm0de on April 26, 2017, 08:41:51 AM

Quote from: rawbot on April 26, 2017, 08:33:54 AM

Jesus christ the problems never stop!!

Now I am getting this error when trying to install AMD APP SDK 3.0 - "This installation package cannot be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify this is a valid Windows installer package"

This was installing fine until today. I can't use claymore without it I don't think so now I can't mine at all.

Have you read my reply on your post a few pages back?

Yes I read it but I haven't had chance to try that because of the new issue. Does Claymore need the AMD APP SDK 3.0 in order to work? It won't install now.

Quote from: EvilC0P on April 26, 2017, 07:45:05 AM

happened to me, my risers were v003 (version printed on the pcb near the x16 slot) and after 3-4 months i realised my voltage were spiking to VERY high once in a while (i have hwmonitor running to check status of my video cards) and once in a while it would cause my system to shutdown. i couldn't track it the issue until amorning when i booted the system that one of my rx480 burnt in front of me! sparkles and little firework under the heatsink.
first this happened to me, a chip/solder were burned on the riser. that's how i realised how garbage they were. thrwe them all away and bought v007 a month ago and since then, never saw any voltage spike in hwmonitor.

all i'm saying, to protect your equipment, buy quality parts. (the risers i bought v003 were like 7$ and the v007 i'm getting now are 15$ CAD, worth it and i won't come back home with my house on fire...)
happy mining

I can only find version 6c on UK ebay. the current ones I have are version 3. Would version 006c be OK?
http://www.ebay.co.uk/itm/5Pcs-USB3-0-PCI-E-Express-1x-To-16x-Extender-Riser-Card-Adapter-SATA-6Pin-Cable/142161974954?_trksid=p2047675.c100005.m1851&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D2%26asc%3D40656%26meid%3D2b9244d4aa2c45eca2f84e031a58b965%26pid%3D100005%26rk%3D3%26rkt%3D6%26sd%3D152461816564

that looks fine, i would say it's the minimum to be sure. but ya i remember wasting hours searching through all the damn ads on ebay and many sellers don't post a decent picture showing the version.

delle54

sr. member

Activity: 307

Merit: 250

Quote from: xanx on April 26, 2017, 08:53:30 AM

ethermine.org down for yall? Whats popping

Only the frontend. Mining is running as usual.

xanx

newbie

Activity: 37

Merit: 0

ethermine.org down for yall? Whats popping

rawbot

sr. member

Activity: 458

Merit: 250

Quote from: Godm0de on April 26, 2017, 08:41:51 AM

Quote from: rawbot on April 26, 2017, 08:33:54 AM

Jesus christ the problems never stop!!

Now I am getting this error when trying to install AMD APP SDK 3.0 - "This installation package cannot be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify this is a valid Windows installer package"

This was installing fine until today. I can't use claymore without it I don't think so now I can't mine at all.

Have you read my reply on your post a few pages back?

Yes I read it but I haven't had chance to try that because of the new issue. Does Claymore need the AMD APP SDK 3.0 in order to work? It won't install now.

Quote from: EvilC0P on April 26, 2017, 07:45:05 AM

happened to me, my risers were v003 (version printed on the pcb near the x16 slot) and after 3-4 months i realised my voltage were spiking to VERY high once in a while (i have hwmonitor running to check status of my video cards) and once in a while it would cause my system to shutdown. i couldn't track it the issue until amorning when i booted the system that one of my rx480 burnt in front of me! sparkles and little firework under the heatsink.
first this happened to me, a chip/solder were burned on the riser. that's how i realised how garbage they were. thrwe them all away and bought v007 a month ago and since then, never saw any voltage spike in hwmonitor.

all i'm saying, to protect your equipment, buy quality parts. (the risers i bought v003 were like 7$ and the v007 i'm getting now are 15$ CAD, worth it and i won't come back home with my house on fire...)
happy mining

I can only find version 6c on UK ebay. the current ones I have are version 3. Would version 006c be OK?
http://www.ebay.co.uk/itm/5Pcs-USB3-0-PCI-E-Express-1x-To-16x-Extender-Riser-Card-Adapter-SATA-6Pin-Cable/142161974954?_trksid=p2047675.c100005.m1851&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D2%26asc%3D40656%26meid%3D2b9244d4aa2c45eca2f84e031a58b965%26pid%3D100005%26rk%3D3%26rkt%3D6%26sd%3D152461816564

Godm0de

newbie

Activity: 12

Merit: 0

Quote from: rawbot on April 26, 2017, 08:33:54 AM

Jesus christ the problems never stop!!

Now I am getting this error when trying to install AMD APP SDK 3.0 - "This installation package cannot be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify this is a valid Windows installer package"

This was installing fine until today. I can't use claymore without it I don't think so now I can't mine at all.

Have you read my reply on your post a few pages back?

rawbot

sr. member

Activity: 458

Merit: 250

Jesus christ the problems never stop!!

Now I am getting this error when trying to install AMD APP SDK 3.0 - "This installation package cannot be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify this is a valid Windows installer package"

This was installing fine until today. I can't use claymore without it I don't think so now I can't mine at all.

LeonManveli

newbie

Activity: 23

Merit: 0

Yiimp is now working

Decred port changed from 4252 to 3252

golden0707

full member

Activity: 189

Merit: 100

Quote from: Claymore on April 26, 2017, 07:39:41 AM

I managed to get speed similar to v9.0 with speed stability better than in v9.2. I will release new version in 2-3 days including this and some other improvements.

Veeeeeeery nice

EvilC0P

newbie

Activity: 50

Merit: 0

Quote from: rawbot on April 25, 2017, 04:00:06 PM

Quote from: eafindme on April 25, 2017, 08:02:05 AM

Quote from: rawbot on April 25, 2017, 07:57:38 AM

Quote from: notbatman on April 25, 2017, 07:50:23 AM

Quote from: rawbot on April 25, 2017, 07:47:01 AM

Quote from: vapourminer on April 24, 2017, 04:23:11 PM

Quote from: rawbot on April 24, 2017, 01:10:28 PM

I'm sick to death of my miner crashing. I have six rx 470 8gb sapphire cards and it can run ok for days, then locks up. Then I have to restart it about 10-20 times because I constantly get the message "Ethdcrminer64.exe has stopped working". Then I go into GPUZ and see that one of the cards is not reporting data fully. After 10 restart or so it starts working again, and I get a few more days mining, sometimes less.

What could be causing this? All cards are cool, well ventilated running at 74 degrees contant. this issue is really pissing me off now. All parts are relatively high quality, EVGA power supply etc.

I am running win 10 64 bit

remove and reseat everything. run memtest86 overnight.

all vbios stock?

No I modded them for extra mining capabilities and it worked well for a while but now it's crashing a lot. I am sick to death of the "Dcrethminer64.exe has stopped working" error.

Check gpu-z for cards with Hynix ram lol.

GPUZ reports the ram as 8gb samsung. But sometimes certain bits of data are missing from the gpuz report on one card or another. Can't remember exactly which bits of data, they are usually blank. When you see that you know without doubt claymore is going to crash. But sometimes it still crashes when GPU is reporting everything is OK on all cards. It's a shame because if this carries on I will have to sell up. I just ROI'd thanks to the ethereum price shooting up but I wanted to run it for a year or so. It is taking up so much time now and I cannot nail down the issue(s).

Do you check the PCIE riser? GPU also draw power from motherboard through PCIE.

Well I have unplugged the power connector then plugged it back in, I don't know how else I can check it. What I can't understand is how can the risers be malfunctioning all of a sudden after days of mining? The miner doesn't move, the GPU's are secure. How can they work for days, then fail, then after a few restarts begin working again. There is no logic there unless I am missing something.

happened to me, my risers were v003 (version printed on the pcb near the x16 slot) and after 3-4 months i realised my voltage were spiking to VERY high once in a while (i have hwmonitor running to check status of my video cards) and once in a while it would cause my system to shutdown. i couldn't track it the issue until amorning when i booted the system that one of my rx480 burnt in front of me! sparkles and little firework under the heatsink.
first this happened to me, a chip/solder were burned on the riser. that's how i realised how garbage they were. thrwe them all away and bought v007 a month ago and since then, never saw any voltage spike in hwmonitor.

all i'm saying, to protect your equipment, buy quality parts. (the risers i bought v003 were like 7$ and the v007 i'm getting now are 15$ CAD, worth it and i won't come back home with my house on fire...)
happy mining

Claymore

donator

Activity: 1610

Merit: 1325

Miners developer

I managed to get speed similar to v9.0 with speed stability better than in v9.2. I will release new version in 2-3 days including this and some other improvements.

kostickole92

newbie

Activity: 20

Merit: 0

Quote from: coinzoid on April 26, 2017, 05:06:18 AM

Dear Claymore,

I'm using followin bat file at 9.2 to mine ETH (ethermine) and DCR (coinmine.pl)

Quote

start/high EthDcrMiner64.exe -epool eu2.ethermine.org:4444 -ewal mywalletID.WorkerName -epsw x -dpool stratum+tcp://dcr-eu.coinmine.pl:2222 -dwal MyUserName.WorkerName -dpsw xxy342 -dcri 30 -mode 0 -wd 1 -tt 80 -ttdcr 76 -ttli 78 -tstop 85

I'm experiencing speed fluctations on my Windows 10 pro x64. Any ideas? Do I also need to include asm parameter in my bat file?

Besides, anyone can recommend a bat file for expanse and dcr mining with 9.2 release?

I have same problem, but now i have little stable claymore 9.2 use 16.10.2 driver, try 16.11.5 its same ..... i put -ethi 16, -dcri 29, 1100CC / 2000MC, RX480 8gb .......try -ethi and -dcri +/-, and found good setings for your cards ......... good stable is for -ethi 4 or -ethi 6, and -dcri 17 but have a bit less spead ....... any have better idea for this flctuation and unstable claymor ..... Huh

ccminer.net

sr. member

Activity: 595

Merit: 251

Quote from: ultramilkwai on April 26, 2017, 06:12:46 AM

Quote from: ccminer.net on April 26, 2017, 05:18:28 AM

I'm dual mining ETC and DCR at the moment

With ETC no issues, but with DCR, on supernova pool I got all the shares REJECTED!
Are you facing the same issue or maybe I miss some config??

Did you remember to change the port from 2252 (old) -> 3252 (new)

Yes!!
they confirmed 1 share, out of like 40!?!?!?! Huh

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 919. (Read 6590718 times)