Claymore's ZCash/BTG AMD GPU Miner v12.6 (Windows/Linux) - page 362.

rpg

hero member

Activity: 728

Merit: 500

Quote from: yudhistira on December 10, 2016, 06:32:40 AM

Dual-X R9 280X 3G D5

win7 4 Gb RAM, 16 Gb virtual RAM
radeon software ver 16.9.2
zecminerx64.exe -zpool ssl suprnova -i 8
hashrate avg 200 h/s
hashrate do not match between pools and my rig
and always : share rejected 5

is this normal ?

Yes. Pools steal shares from you. The only zcash pool that reports and pays correctly what is expected is dwarfpool.

Nagadota

hero member

Activity: 574

Merit: 500

ClaimWithMe - the most paying faucet of all times!

Quote from: ?? on ??

Quote from: ober on December 10, 2016, 05:18:30 AM

Quote from: ?? on ??

I installed relive 16.12.1 driver got code 43 error.
Reverted back to 16.11.5 work perfectly

Ps. My 470s were bios modded

Did you use DDU or windows rollback? Because AMD utility doesn't work and they mention it only in release notes for Pro cards:
http://support.amd.com/en-us/kb-articles/Pages/AMD-FirePro-and-Radeon-Pro-Software-Crimson-ReLive-Edition.aspx

Quote

Using AMDCleanUpUtility.exe directly to uninstall the driver may not perform as expected

Juz use the latest ddu to uninstall 16.12.1, u will be fine

DDU is best. It is much better than the AMD clean utility. But make sure you reboot into safe mode to do the clearn up.

beIbox

newbie

Activity: 21

Merit: 0

Quote from: Murval on December 10, 2016, 09:19:54 AM

Hi All!

Is it strongly recommended to use only 15.12 crimson drivers version?
Higher version not better?

+10-12 H/s with 15.12 in my case.
Windows 10, r9 390/390x

bisba

full member

Activity: 202

Merit: 100

Quote from: AlcatelBravo on December 10, 2016, 03:51:03 AM

Hmm I have run the new Claymores v9.1 GPU miner for zcash and I am getting about a 10sol/s increase on each of my 280x GPU's (Same settings as previously used)

I haven't tested the power draw yet and compared it to V8 but if it uses more power for an extra 10sol/s than V8 then it might be better to just stick to that one and pay the additional 0.5% fee.

hello friend

i mining with 280x too...

what settings you use??oc etc?

Murval

newbie

Activity: 9

Merit: 0

Hi All!

Is it strongly recommended to use only 15.12 crimson drivers version?
Higher version not better?

Svedge

newbie

Activity: 1

Merit: 0

Don't download the 16.12.1 drivers, horrible hashrate on my 290 cards and not compatible with the current MSI Afterburner. I reverted back 16.11.2 instantly.

oslak

sr. member

Activity: 273

Merit: 250

Quote from: yudhistira on December 10, 2016, 08:17:46 AM

Quote from: oslak on December 10, 2016, 07:06:50 AM

Quote from: yudhistira on December 10, 2016, 06:32:40 AM

Dual-X R9 280X 3G D5

win7 4 Gb RAM, 16 Gb virtual RAM
radeon software ver 16.9.2
zecminerx64.exe -zpool ssl suprnova -i 8
hashrate avg 200 h/s
hashrate do not match between pools and my rig
and always : share rejected 5

is this normal ?

yes
http://imgur.com/a/OOubg

share rejected is always same value
what that means

16 rejects for 2 hours. mostly when submitWork is late, auto reject from pool.

yudhistira

full member

Activity: 347

Merit: 100

Quote from: oslak on December 10, 2016, 07:06:50 AM

Quote from: yudhistira on December 10, 2016, 06:32:40 AM

Dual-X R9 280X 3G D5

win7 4 Gb RAM, 16 Gb virtual RAM
radeon software ver 16.9.2
zecminerx64.exe -zpool ssl suprnova -i 8
hashrate avg 200 h/s
hashrate do not match between pools and my rig
and always : share rejected 5

is this normal ?

yes
http://imgur.com/a/OOubg

share rejected is always same value
what that means

vapourminer

legendary

Activity: 4354

Merit: 3614

what is this "brake pedal" you speak of?

Quote from: Vaculin on December 10, 2016, 05:09:41 AM

Quote from: RidgyDidge on December 10, 2016, 04:05:35 AM

Quote from: banzsolt1 on December 10, 2016, 04:02:36 AM

Is it me the only one who is getting a lot of connection failed retry to connect in 20 sec?

All my miners started doing this, and my pool stats show 30% less hashrate like this.

Version 9/9.1 isn't worth the hassle if your rigs were working fine and are now playing up, even if you get a lesser fee then Version 8 stick to being stable and hashing stable.

The newer versions seem nuked to me...

You just need to reduce the voltage or the clock frequency so that it will stress the PSU less. That should solve the problem.

actually, i increased the voltage to my 390s. apparently the prior undervolt that v8 was ok with was too much for v9. bumped it from -75 to -50.

been rock solid since.

gennadiv

full member

Activity: 139

Merit: 100

working with all versions on r9 380 graphics cards behave well and work steadily and on version version v9.1: the difference in the hashes's almost never seen ZEC: 12/10/16-18:57:05 - New job from equihash.eu.nicehash.com:3357
ZEC - Total Speed: 496.454 H/s, Total Shares: 175, Rejected: 0, Time: 00:14
ZEC: GPU0 166.981 H/s, GPU1 164.576 H/s, GPU2 164.897 H/s
GPU0 t=69C fan=67%, t GPU1=64C fan=47%, GPU2 t=66C fan=57%
ZEC: 12/10/16-18:57:22 - SHARE FOUND - (GPU 2)
ZEC: Share accepted (172 ms)!
ZEC: 12/10/16-18:57:23 - SHARE FOUND - (GPU 2)
ZEC: Share accepted (187 ms)!

beIbox

newbie

Activity: 21

Merit: 0

9.1 is working like a charm, even on shitty VTX3D Grin

thank you, Claymore!

ioglnx

sr. member

Activity: 574

Merit: 250

Fighting mob law and inquisition in this forum

v9.1 is much more stable and works reliable!
Thanks Claymore.

oslak

sr. member

Activity: 273

Merit: 250

Quote from: yudhistira on December 10, 2016, 06:32:40 AM

Dual-X R9 280X 3G D5

win7 4 Gb RAM, 16 Gb virtual RAM
radeon software ver 16.9.2
zecminerx64.exe -zpool ssl suprnova -i 8
hashrate avg 200 h/s
hashrate do not match between pools and my rig
and always : share rejected 5

is this normal ?

yes
http://imgur.com/a/OOubg

iMish

newbie

Activity: 91

Merit: 0

Quote from: bebel00 on December 09, 2016, 10:19:44 PM

Quote from: TeamButtcoin on December 09, 2016, 09:32:49 PM

I've tested the v9.1 but I prefer the v9.0 version. With v9.1 I lose around 12 15 sol per card.

For me v8 worked fine on 6 RX 470 8gb . On 9 I could not make it work. It crashed after a few minutes or max an hour. (tried what was suggested around here and it crashed ) (have a 1200w PSU)
After a few tests on v 9 and then Claymore for ETH I found that a GPU just made the system crash each time .... even tho everything worked fine on v 8. After removing all cards except the one that made the system crash..I then changed the cables...riser and mined only with it on v8 v9 and ETH - on ETH and v9 it crashed each time so now I'm 100% sure that GPU was at fault .

No idea why..but I'll prob return that GPU. All cards were stock (new) and no changes in Trixx.
Anybody had something like this happen ?

On 5 cards and v9 the system looks stable and I'm getting same performance like with 6 on v8

Also...I see drivers 15.12 suggested . Can't find a valid download link for Win 10 x64. A valid link to download ?

one of my RX 480s does not support v9 either

i'm using -di to disable it and using it for dual mining ETH + SIA

iMish

newbie

Activity: 91

Merit: 0

Quote from: TheRider on December 09, 2016, 10:33:03 PM

Quote from: suggsy89 on December 09, 2016, 08:21:12 PM

Quote from: TheRider on December 09, 2016, 08:07:12 PM

Quote from: TheRider on December 09, 2016, 07:55:15 PM

Quote from: TheRider on December 09, 2016, 12:34:31 PM

v9.1

ZecMiner64.exe -mport 0 -zpool ssl://asia1-zcash.flypool.org:3443 -zwal t1xxxx.worker -zpsw x -i 8 -dbg -1

ZEC: Stratum - connecting to 'asia1-zcash.flypool.org' <209.58.164.95> port 3443 (SSL/TLS)
Cannot establish SSL/TLS connection
ZEC: Stratum - Cannot connect to asia1-zcash.flypool.org:3443
ZEC: Stratum - Failed to connect, retry in 20 sec...
GPU0 t=30C fan=0%, GPU1 t=29C fan=0%, GPU2 t=22C fan=64%

Am I doing something wrong?

STILL CANT CONNECT SSL.

9.1 can't connect using SSL to flypool servers (tried all servers), so I have to use non-encrypted connection.

BUT, DevFee defaults to SSL, and when DevFee can't connect, my rig stops mining in the middle of the night!!

Can someone please help?

@ocminer, can't connect to suprnova with SSL. Any help?

I just tried your config.. Works fine!?

ZEC: Stratum - connecting to 'asia1-zcash.flypool.org' <209.58.164.95> port 3443 (SSL/TLS)
SSL/TLS encryption is enabled
ZEC: Stratum - Connected (asia1-zcash.flypool.org:3443) (SSL/TLS)
ZEC: Authorized
Pool sets new share target: 0x0020c49b (diff: 2000H)
ZEC: 12/10/16-00:19:11 - SHARE FOUND - (GPU 1)
ZEC: Share accepted (219 ms)!
ZEC: 12/10/16-00:19:12 - SHARE FOUND - (GPU 3)
ZEC: Share accepted (219 ms)!

Still no luck. I'm forced to use -r 20 to make sure the miner restarts and continues mining. I prefer the short interruptions to having the DevFee cause the miner to stop entirely because it can't connect on SSL.

I'm out of ideas on how to troubleshoot why I can't connect using SSL...

use -zpool ssl://zec.suprnova.cc:2242 it should work for suprnova

for flypool add ssl:// to address

vi1son

hero member

Activity: 531

Merit: 500

Seems like my 7850 little faster in 9.1 : +1-2H/s

yudhistira

full member

Activity: 347

Merit: 100

Dual-X R9 280X 3G D5

win7 4 Gb RAM, 16 Gb virtual RAM
radeon software ver 16.9.2
zecminerx64.exe -zpool ssl suprnova -i 8
hashrate avg 200 h/s
hashrate do not match between pools and my rig
and always : share rejected 5

is this normal ?

QuintLeo

legendary

Activity: 1498

Merit: 1030