EWBF's CUDA Zcash miner - page 39. | Bitcointalksearch.org

stash2coin

jr. member

Activity: 108

Merit: 1

Quote from: jpl on November 07, 2017, 01:01:06 AM

Is EWBF compiled for 32bit or 64bit? It says it is running on C:\windows\system32\cmd.exe Obviously that is 32bit does it matter? (I'm on win10 64 bit)
thanks

Its a x64 bit application what your looking at is windows command prompt and not related directly to ewbf miner

hanskan

full member

Activity: 336

Merit: 100

Quote from: GustETH on November 06, 2017, 06:31:12 PM

Quote from: hanskan on November 06, 2017, 02:46:29 PM

Quote from: GustETH on November 06, 2017, 06:59:21 AM

what does it mean "Device: 4 thread exited with code: 73 " Huh

You have overclocked too much. Lower the clock setting and you should be fine

what clock: core clock or mem clock?
device 4 is a Asus Strix GTX1070 non oc version (STRIX-GTX1070-8G-GAMING)

Downclock both and test it, if it runs 8 hours straight with no crash then it should be stable. My 1070s run on very low clocks and tdp to achieve maximum efficiency. 67% tdp, +99core +249mem

jpl

member

Activity: 154

Merit: 11

Is EWBF compiled for 32bit or 64bit? It says it is running on C:\windows\system32\cmd.exe Obviously that is 32bit does it matter? (I'm on win10 64 bit)
thanks

GustETH

newbie

Activity: 19

Merit: 0

Quote from: Atexor on November 06, 2017, 01:50:39 PM

I hope that new version of EWBF's miner will receive functionality to not close if there is to connection to any pool - for instance the case, when there is no ethernet connection. It would attempts to connect infinity times until it will be successful.

Sometimes there are cases when ethernet provider has problems with ethernet and then miner disables itself.
Addind/removing and changing exit parameter doesn' work for me as I want.

What new version Huh

?
the developer has not been active for quite some time

GustETH

newbie

Activity: 19

Merit: 0

Quote from: hanskan on November 06, 2017, 02:46:29 PM

Quote from: GustETH on November 06, 2017, 06:59:21 AM

what does it mean "Device: 4 thread exited with code: 73 " Huh

You have overclocked too much. Lower the clock setting and you should be fine

what clock: core clock or mem clock?
device 4 is a Asus Strix GTX1070 non oc version (STRIX-GTX1070-8G-GAMING)

hanskan

full member

Activity: 336

Merit: 100

Quote from: GustETH on November 06, 2017, 06:59:21 AM

what does it mean "Device: 4 thread exited with code: 73 " Huh

You have overclocked too much. Lower the clock setting and you should be fine

BlockMedx

newbie

Activity: 56

Merit: 0

Has anybody else been getting the BSOD error once you launch the miner? Been having serious problems getting my rig to be stable. It BSOD's after about 3 seconds

Atexor

member

Activity: 155

Merit: 10

I hope that new version of EWBF's miner will receive functionality to not close if there is to connection to any pool - for instance the case, when there is no ethernet connection. It would attempts to connect infinity times until it will be successful.

Sometimes there are cases when ethernet provider has problems with ethernet and then miner disables itself.
Addind/removing and changing exit parameter doesn' work for me as I want.

syauqialbaana

full member

Activity: 220

Merit: 100

Hello everyone, I have a question, I run the miner with api, immediately it works as it should, but after a while, just the ip address is unavailable. But the miner himself continues to work as before. What could be the problem?

GustETH

newbie

Activity: 19

Merit: 0

what does it mean "Device: 4 thread exited with code: 73 " Huh

dragonmike

hero member

Activity: 1274

Merit: 556

Quote from: Makak4R on November 06, 2017, 01:48:04 AM

Quote from: wudafuxup on November 05, 2017, 08:58:23 PM

Quote from: dragonmike on November 04, 2017, 05:55:56 AM

Quote from: dragonmike on November 03, 2017, 02:14:33 PM

5x 1080 rig, trying to mine BitcoinZ. Power target@80%, core +110, mem +800. Forced P0 state.

One of my GPUs is gradually losing speed using EWBF.
I've been mining other algos for days without interruption but as I tried to switch to mining equihash with EWBF this crap starts happening. Hashrate goes down, lower and lower until it crashes the rig. Any ideas what might cause it?

Do you guys know whether this could be either Cuda9 or driver related? It just makes no sense to me...

That's really interesting. I have had this issue for a while now. I have 2 Z97 Extreme 4 boards mining some Zencash. The first one had six GTX1060 and the 2nd one had six GTX1080tis. Both run windows 10, but the miner with my GTX1060s stopped working with 6 cards randomly. It does exactly what you explained. It works with 5 perfectly (even though it used to work with 6 for about 3 months) but once you install the 6th it slowly drops and eventually crashes the system. I have tested all the cards and they all work perfectly individually. I'm starting to think it might be a windows corruption issue of some sort. Would be cool if anyone has found a way to fix this issue.

I can confirm that too, I have strange behavior with one 1070 which works like in half power
other coins seems do not have such issue with that card, it is working on full speed and without issues.
bit when it working on ewbf it srats to do act like that and I do not remember it was acting like this before? Huh

Glad I'm not the only one.
For everyone's benefit, I switched to DSTM's miner, and I am glad to report the slowdown/crashing issue does not happen with that miner, and hashrates are very similar to EWBF's.

So people, just do the switcharoo.

Makak4R

full member

Activity: 266

Merit: 111

Quote from: wudafuxup on November 05, 2017, 08:58:23 PM

Quote from: dragonmike on November 04, 2017, 05:55:56 AM

Quote from: dragonmike on November 03, 2017, 02:14:33 PM

5x 1080 rig, trying to mine BitcoinZ. Power target@80%, core +110, mem +800. Forced P0 state.

One of my GPUs is gradually losing speed using EWBF.
I've been mining other algos for days without interruption but as I tried to switch to mining equihash with EWBF this crap starts happening. Hashrate goes down, lower and lower until it crashes the rig. Any ideas what might cause it?

Do you guys know whether this could be either Cuda9 or driver related? It just makes no sense to me...

That's really interesting. I have had this issue for a while now. I have 2 Z97 Extreme 4 boards mining some Zencash. The first one had six GTX1060 and the 2nd one had six GTX1080tis. Both run windows 10, but the miner with my GTX1060s stopped working with 6 cards randomly. It does exactly what you explained. It works with 5 perfectly (even though it used to work with 6 for about 3 months) but once you install the 6th it slowly drops and eventually crashes the system. I have tested all the cards and they all work perfectly individually. I'm starting to think it might be a windows corruption issue of some sort. Would be cool if anyone has found a way to fix this issue.

I can confirm that too, I have strange behavior with one 1070 which works like in half power
other coins seems do not have such issue with that card, it is working on full speed and without issues.
bit when it working on ewbf it srats to do act like that and I do not remember it was acting like this before? Huh

The_Immortal

newbie

Activity: 55

Merit: 0

Quote from: QuintLeo on November 06, 2017, 12:28:26 AM

Quote from: The_Immortal on November 05, 2017, 06:12:29 PM

Quote from: papampi on November 05, 2017, 02:56:30 AM

Quote from: GustETH on November 04, 2017, 11:04:32 PM

Quote from: minerx117 on November 04, 2017, 05:49:58 PM

Quote from: QuintLeo on November 04, 2017, 01:09:33 PM

Quote from: papampi on November 04, 2017, 06:18:46 AM

I'm sure its been asked but since its impossible to search forum, I should ask again

Can any one explain to me how the fee option works in 3.4 ?
If I set "--fee 1" does the 2% included will be reduced to 1 or it will be 2+1 ?

It should reduce the fee to 1

as far as i can tell there is a default 2% fee, using command --fee 0 removes the fee system all together making it 0% fee...

Regards
Nemo

but reduces the sold / s speed if the fee is turned off?

It really reduce hash rate ?

Nope, it doesn't.

Could someone please test 1070Ti with maximum Power Limit, +650 on memory and about +165 on core? Wanna know what's the maximum hashrate can be expected from that GPU.

Thank you!

Already done in my testing post, though that was at 100% TDP +700 Memory +200 core - right around 540 hash.
90% TDP gave pretty much identical result though.

Well, 100% TDP - is not the maximum

Can you try 110/115/120%? I don't know about its maximum TDP.

QuintLeo

legendary

Activity: 1498

Merit: 1030

Quote from: The_Immortal on November 05, 2017, 06:12:29 PM

Quote from: papampi on November 05, 2017, 02:56:30 AM

Quote from: GustETH on November 04, 2017, 11:04:32 PM

Quote from: minerx117 on November 04, 2017, 05:49:58 PM

Quote from: QuintLeo on November 04, 2017, 01:09:33 PM

Quote from: papampi on November 04, 2017, 06:18:46 AM

I'm sure its been asked but since its impossible to search forum, I should ask again

Can any one explain to me how the fee option works in 3.4 ?
If I set "--fee 1" does the 2% included will be reduced to 1 or it will be 2+1 ?

It should reduce the fee to 1

as far as i can tell there is a default 2% fee, using command --fee 0 removes the fee system all together making it 0% fee...

Regards
Nemo

but reduces the sold / s speed if the fee is turned off?

It really reduce hash rate ?

Nope, it doesn't.

Could someone please test 1070Ti with maximum Power Limit, +650 on memory and about +165 on core? Wanna know what's the maximum hashrate can be expected from that GPU.

Thank you!

Already done in my testing post, though that was at 100% TDP +700 Memory +200 core - right around 540 hash.
90% TDP gave pretty much identical result though.

S_Natural

member

Activity: 154

Merit: 11

Quote from: mettalmag on November 05, 2017, 05:40:14 AM

Quote from: mettalmag on November 04, 2017, 05:30:32 PM

I'm struggling with monitoring system,
Like claymore has dedicated monitoring soft were you can group all the miners and monitor with one web or software instance, is there any solution for EWBF? I have couple 8x1080 rigs and all running ZEC, just wanted to group them and see the monitoring stats on one page, is it possible?

anyone? any ideas?

You can use Claymore's Dual Miner Monitor for mobile to do that. It works perfectly for Claymore, EWBF and Optiminer Wink

wudafuxup

full member

Activity: 391

Merit: 105

Quote from: dragonmike on November 04, 2017, 05:55:56 AM

Quote from: dragonmike on November 03, 2017, 02:14:33 PM

5x 1080 rig, trying to mine BitcoinZ. Power target@80%, core +110, mem +800. Forced P0 state.

One of my GPUs is gradually losing speed using EWBF.
I've been mining other algos for days without interruption but as I tried to switch to mining equihash with EWBF this crap starts happening. Hashrate goes down, lower and lower until it crashes the rig. Any ideas what might cause it?

Do you guys know whether this could be either Cuda9 or driver related? It just makes no sense to me...

That's really interesting. I have had this issue for a while now. I have 2 Z97 Extreme 4 boards mining some Zencash. The first one had six GTX1060 and the 2nd one had six GTX1080tis. Both run windows 10, but the miner with my GTX1060s stopped working with 6 cards randomly. It does exactly what you explained. It works with 5 perfectly (even though it used to work with 6 for about 3 months) but once you install the 6th it slowly drops and eventually crashes the system. I have tested all the cards and they all work perfectly individually. I'm starting to think it might be a windows corruption issue of some sort. Would be cool if anyone has found a way to fix this issue.

The_Immortal

newbie

Activity: 55

Merit: 0

Quote from: papampi on November 05, 2017, 02:56:30 AM

Quote from: GustETH on November 04, 2017, 11:04:32 PM

Quote from: minerx117 on November 04, 2017, 05:49:58 PM

Quote from: QuintLeo on November 04, 2017, 01:09:33 PM

Quote from: papampi on November 04, 2017, 06:18:46 AM

I'm sure its been asked but since its impossible to search forum, I should ask again

Can any one explain to me how the fee option works in 3.4 ?
If I set "--fee 1" does the 2% included will be reduced to 1 or it will be 2+1 ?

It should reduce the fee to 1

as far as i can tell there is a default 2% fee, using command --fee 0 removes the fee system all together making it 0% fee...

Regards
Nemo

but reduces the sold / s speed if the fee is turned off?

It really reduce hash rate ?

Nope, it doesn't.

Could someone please test 1070Ti with maximum Power Limit, +650 on memory and about +165 on core? Wanna know what's the maximum hashrate can be expected from that GPU.

Thank you!

mettalmag

legendary

Activity: 1084

Merit: 1003

≡v≡

Quote from: mettalmag on November 04, 2017, 05:30:32 PM

I'm struggling with monitoring system,
Like claymore has dedicated monitoring soft were you can group all the miners and monitor with one web or software instance, is there any solution for EWBF? I have couple 8x1080 rigs and all running ZEC, just wanted to group them and see the monitoring stats on one page, is it possible?

anyone? any ideas?

papampi

full member

Activity: 686

Merit: 140

Linux FOREVER! Resistance is futile!!!

Quote from: GustETH on November 04, 2017, 11:04:32 PM

Quote from: minerx117 on November 04, 2017, 05:49:58 PM

Quote from: QuintLeo on November 04, 2017, 01:09:33 PM

Quote from: papampi on November 04, 2017, 06:18:46 AM

I'm sure its been asked but since its impossible to search forum, I should ask again

Can any one explain to me how the fee option works in 3.4 ?
If I set "--fee 1" does the 2% included will be reduced to 1 or it will be 2+1 ?

It should reduce the fee to 1

as far as i can tell there is a default 2% fee, using command --fee 0 removes the fee system all together making it 0% fee...

Regards
Nemo

but reduces the sold / s speed if the fee is turned off?

It really reduce hash rate ?

GustETH

newbie

Activity: 19

Merit: 0

Quote from: minerx117 on November 04, 2017, 05:49:58 PM

Quote from: QuintLeo on November 04, 2017, 01:09:33 PM

Quote from: papampi on November 04, 2017, 06:18:46 AM

I'm sure its been asked but since its impossible to search forum, I should ask again

Can any one explain to me how the fee option works in 3.4 ?
If I set "--fee 1" does the 2% included will be reduced to 1 or it will be 2+1 ?

It should reduce the fee to 1

as far as i can tell there is a default 2% fee, using command --fee 0 removes the fee system all together making it 0% fee...

Regards
Nemo

but reduces the sold / s speed if the fee is turned off?

Topic: EWBF's CUDA Zcash miner - page 39. (Read 2164337 times)