Pages:
Author

Topic: Gateless Gate Sharp 1.3.8: 30Mh/s (Ethash) on RX 480! - page 74. (Read 214431 times)

newbie
Activity: 21
Merit: 0
Crash dump has the following. I am just pasting this, if you want the rest of it:https://pastebin.com/W4gHCndP.

Code:
BugCheck 50, {fffffc7e00000000, 0, 0, 6}

Probably caused by : dxgkrnl.sys ( dxgkrnl!DXGADAPTERALLOCATION::~DXGADAPTERALLOCATION+1a )

0: kd> !analyze -v
*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced.  This cannot be protected by try-except.
Typically the address is just plain bad or it is pointing at freed memory.
Arguments:
Arg1: fffffc7e00000000, memory referenced.
Arg2: 0000000000000000, value 0 = read operation, 1 = write operation.
Arg3: 0000000000000000, If non-zero, the instruction address which referenced the bad memory
address.
Arg4: 0000000000000006, (reserved)


newbie
Activity: 1
Merit: 0
Not sure if anyone else has had issues with high DPI displays and GGS, but I couldn't see the checkboxes for selecting active GPUs when I updated from 1.2.2 to 1.2.7 (Win10, desktop resolution is 3840x2160). Changing the DPI scaling options in Properties fixed the table showing properly so I could actually activate the GPUs I wanted. Kinda obvious solution to try but just thought I'd throw it out there in case anyone ran into the same issue and wasn't sure. Screenshot for option to change: https://imgur.com/s7jOCa6
full member
Activity: 364
Merit: 106
ONe Social Network.
can you make option to disable the charts? they just use alot of cpu power
ggs is using 50% cpu power on cryptonight for me
newbie
Activity: 21
Merit: 0
Are you using the recommended driver (18.1.1) with CrossFire off?
The log file is in %AppData%.

18.1.1 freshly installed (had 17.12.2 but removed with DDU)
I don't even have the CrossFire option in Global Gaming

I don't see anything in the log that's tellling. This is the last few entries before the last blue screen....there is nothing. Anyway to increase the logging?

Code:
2018-01-23 18:52:48.6626 [13] Received new job: 6d8f
2018-01-23 18:52:49.0245 [14] Device #1: 591.57 Kh/s (NeoScrypt)
2018-01-23 18:52:52.6321 [7] Device #0: 562.71 Kh/s (NeoScrypt)
2018-01-23 18:52:53.6751 [13] Received new job: 6d94
2018-01-23 18:52:58.6864 [13] Received new job: 6d9a
2018-01-23 18:52:59.0392 [14] Device #1: 607.39 Kh/s (NeoScrypt)
2018-01-23 18:53:02.6478 [7] Device #0: 590.15 Kh/s (NeoScrypt)
2018-01-23 18:53:03.6985 [13] Received new job: 6d9f
sr. member
Activity: 728
Merit: 304
Miner Developer
Ahh, well that was too soon. It crashed again. Windows page fault. I have scanned the drive and ran sfc /scannow and no errors.
Any thoughts on this? Is there a log I can pull info from or setup to help?

Edit:Where does this application even log to? I see nothing in the install dir.


Are you using the recommended driver (18.1.1) with CrossFire off?
The log file is in %AppData%.
jr. member
Activity: 98
Merit: 2
Is there any way to log everything in the log file? I need this to debug witch one of 8 GPU hangs the miner and system.

Thanks
newbie
Activity: 21
Merit: 0
Ahh, well that was too soon. It crashed again. Windows page fault. I have scanned the drive and ran sfc /scannow and no errors.
Any thoughts on this? Is there a log I can pull info from or setup to help?

Edit:Where does this application even log to? I see nothing in the install dir.
newbie
Activity: 21
Merit: 0
great miner .....
I create custom bios example with 1.2.6

sapphire RX 580 Nitro + 8GB
ETH 30-32 MH / s, XMR 990-1100H / s Micron


Bios Sapphire Pulse ITX RX 570 4GB Elpida / Hynix ETH 29-31MH / s Elpida, ETH 28-29MH / s Hynix
XMR 1000 H / s Elpida, XMR 990 H / s Hynix

all cards 560/570/580 with stable custom settings and low power
if you are looking for send me pm

I am looking! I have an MSI Gaming X 4G with hynix ajr. Will that BIOS work?
I tried to PM but you're setup to block newbies Cry
newbie
Activity: 1
Merit: 0
Gigabyte RX560 4GB Shaders 1024 Memory Hynix
ver. 1.2.4 alpha
pool NiceHash

NeoScrypt (Feathercoin) 340 Kh/s
CryptoNight (Monero) 435 H/s
Ethash (Ethereum) 14.2 Mh/s

ver. 1.2.7 alpha
pool NiceHash

NeoScrypt (Feathercoin)  320 Kh/s
CryptoNight (Monero) 380 H/s
Ethash (Ethereum) 11.2 Mh/s

Claymore 10
pool NiceHash
-mode 1

Ethereum 15.9 Mh/s

My Results
Google translator
I do not speak English
newbie
Activity: 21
Merit: 0
Thanks for the miner. I was seeing some crashing with GGS 1.2.5. It worked well at first then I had a crash after about 12 hours, then it crashed pretty constantly after a few minutes so I've installed GGS 1.2.7 and installed 18.1.1.
I reverted to stock settings for now, minus the memory timings (1500 copied up). Two MSI RX570 Gaming X 4GB Hynix AJR currently getting ~600KH/s on Neoscrypt. Looking to prove that the crashing is resolved and then work to get more out of these cards. I'd love to get near 1000 KH/s!
sr. member
Activity: 728
Merit: 304
Miner Developer
I found a way to switch to/from the DEVFEE mode instantaneously.
This should solve all the problems with the DEVFEE mode.
We will see...
sr. member
Activity: 1484
Merit: 253
After some time during mining 1.2.7 starts to jumps with CPU usage from 1-2% up to 9-14%. This make average CPU load higher up to 5-6%... Not so bad, but 1.2.6 was better with this...
Even when mining is stopped CPU usage remains 4-6%. Releasing vmemory didn't helps...
Closing GGS and starting again resolves this and CPU usage back 1-2%.

EDIT: After 30 min CPU usage allready 2-4%...
newbie
Activity: 31
Merit: 0
I sent you an email
member
Activity: 176
Merit: 10
send me a pm

hi maverik77,can i let you a pm for 570 bios?
newbie
Activity: 126
Merit: 0
I was able to fix Monero. Still trying to get ETH working
newbie
Activity: 40
Merit: 0
https://imgur.com/a/k24So

That's my main problem - it is my hashrate drop after the first devfee switch. It happens only after switching. And the programm is freezing...


13 GPU's? Oh my, oh my. Let me see what I can do...

But I have the same issue with smaller count of gpus. Only with neoscrypt.

Drivers: Latest 18.1.1
Win 10 x64
4GB DDR4 (used about 50%)
38GB virtual memory
Intel Pentium G4400

PS
Please, make an option to switch on/off the graphics bar (statistics). 
sr. member
Activity: 728
Merit: 304
Miner Developer


That's my main problem - it is my hashrate drop after the first devfee switch. It happens only after switching. And the programm is freezing...


13 GPU's? Oh my, oh my. Let me see what I can do...
newbie
Activity: 40
Merit: 0
https://imgur.com/a/k24So

That's my main problem - it is my hashrate drop after the first devfee switch. It happens only after switching. And the programm is freezing...
newbie
Activity: 31
Merit: 0
version stable.....okkkk

https://imgur.com/xP4SnpN
newbie
Activity: 31
Merit: 0
send me a pm
Pages:
Jump to: