Possible solution
https://bitcointalksearch.org/topic/m.13041201
Topic: [Guide] Dogie's Comprehensive Black Arrow Prospero X1 Setup [HD] (Read 8713 times)
November 21, 2015, 05:13:30 PM
I'm checking into it. In the meantime, I found a miner manager from blackarrow called Miner operator
http://ecointalk.net/topic/1761-miner-operator/
I'm thinking the software version is out of date. I'll post here if I have luck with it. Regardless, it's a nice little program.
http://ecointalk.net/topic/1761-miner-operator/
I'm thinking the software version is out of date. I'll post here if I have luck with it. Regardless, it's a nice little program.
November 21, 2015, 03:16:09 AM
Maybe you can help me. I turned the X3 off for a couple weeks. When I turned it back on, it's hashing just fine, I can see my stats on the pool site. However, I can't access the login. It used to be 192.168.1.60, but now it just hangs saying there is nothing there. I just want to change the pool settings.
I am unsure what recovery options you have on an X3, but this is a common problem with the controller. Is there an SD card?
November 20, 2015, 02:51:35 PM
Maybe you can help me. I turned the X3 off for a couple weeks. When I turned it back on, it's hashing just fine, I can see my stats on the pool site. However, I can't access the login. It used to be 192.168.1.60, but now it just hangs saying there is nothing there. I just want to change the pool settings.
Any advice would be appreciated!
Darcie~!
Any advice would be appreciated!
Darcie~!
October 02, 2014, 11:59:33 AM
It looks pretty badass too. Thanks for the guide! 
October 02, 2014, 11:12:21 AM
Dogie's Miner Setup Guides:
Nicely formatted version available at dogiecoin.com!
Contents:
0a) What to Expect
0b) What You Need
1) Powering
2) Cooling
3) Case
4) Configuration
5) Troubleshooting
6) Where to buy
0a) What to Expect (top)
The Prospero X1 by Black Arrow is a small, consumer unit that includes a controller and power supply. It is the only miner on the market that utilises just
one internal ASIC, and also the only miner to have so many ancillary features on a smaller miner.
0b) What You Need (top)
You will need a few accessories to get started.
Click your flag to find everything you need to get started at Amazon!
1) Powering (top)
X1s come with an internal 140W AP187 PSU by Sunshine Electronics. Its an unusual formfactor which also uses a 20 pin output to power the miner. This
means you can NOT replace it with a conventional PSU. Please note that it requires a "Mickey Mouse" / Cloverleaf cable rather than the usual C13 - see
section 0b for links.
2) Cooling (top)
The X1 utilises a 200mm CoolerMaster MegaFlow 200 which is near silent during operation. Air is pulled in through the bottom of the case, drawn through
the heatsink and PSU before being exhausted out the top of the case in a negative pressure tunnel arrangement. The Minion ASIC itself features an
aluminium finned heatsink with four copper heatpipes distributing heat.
3) Case (top)
Each unit is full enclosed in a The S3 is entirely enclosed in an extremely strong aluminium case. I personally had problems with the screws holding my unit
closed, such that many had to be drilled out. This is not likely to be a common problem. Later revisions come with a touchscreen LCD display and full
Android device. A keyboard can be plugged into the miner via USB to help type so the miner can be standalone. Later revisions may also come with an
external Wifi antennae.
An X1 measures 222 x 205 x 80mm and weighs 2.1kg.
4) Configuration (top)
The X1 is standalone and does not require an external controller.
Wiring:
Configuration:
Antpool Register!
5) Troubleshooting (top)
TBD as problems arise.
Legal disclaimer: This information is for general guidance and does not constitute expert advice. We are not responsible if you, your property or a third
party is injured or damaged as a result of any interaction with this information, and no warranty is provided. All text and images are covered by copyright.
6) Where to buy (top)
Nicely formatted version available at dogiecoin.com!
Contents:
0a) What to Expect
0b) What You Need
1) Powering
2) Cooling
3) Case
4) Configuration
5) Troubleshooting
6) Where to buy
0a) What to Expect (top)
The Prospero X1 by Black Arrow is a small, consumer unit that includes a controller and power supply. It is the only miner on the market that utilises just
one internal ASIC, and also the only miner to have so many ancillary features on a smaller miner.
| Chips | 1x 28nm Minion |
| Hashrate | ~100GH |
| Rated Voltage | 12V |
| Rated Current | 8.3A |
| Power.Consumption | 100W |
0b) What You Need (top)
You will need a few accessories to get started.
Click your flag to find everything you need to get started at Amazon!
1) Powering (top)
X1s come with an internal 140W AP187 PSU by Sunshine Electronics. Its an unusual formfactor which also uses a 20 pin output to power the miner. This
means you can NOT replace it with a conventional PSU. Please note that it requires a "Mickey Mouse" / Cloverleaf cable rather than the usual C13 - see
section 0b for links.
2) Cooling (top)
The X1 utilises a 200mm CoolerMaster MegaFlow 200 which is near silent during operation. Air is pulled in through the bottom of the case, drawn through
the heatsink and PSU before being exhausted out the top of the case in a negative pressure tunnel arrangement. The Minion ASIC itself features an
aluminium finned heatsink with four copper heatpipes distributing heat.
3) Case (top)
Each unit is full enclosed in a The S3 is entirely enclosed in an extremely strong aluminium case. I personally had problems with the screws holding my unit
closed, such that many had to be drilled out. This is not likely to be a common problem. Later revisions come with a touchscreen LCD display and full
Android device. A keyboard can be plugged into the miner via USB to help type so the miner can be standalone. Later revisions may also come with an
external Wifi antennae.
An X1 measures 222 x 205 x 80mm and weighs 2.1kg.
4) Configuration (top)
The X1 is standalone and does not require an external controller.
Wiring:
- Plug in an ethernet cable from the X1 to you router.
- Plug in the power cable from the X1 to the mains.
Configuration:
- The unit will automatically power on.
- The unit will ship with DHCP enabled, and so your router will assign it an appropriate IP address automatically.
- If you have an LCD model, the IP address will be displayed on the LCD. If not, using a browser, navigate to your router and find the IP it has
assigned the S3 and navigate to that IP. - Login using "user" as the username and "blackarrow" as the password.
- Select "Prospero" on the left, and then navigate to the "Pools" tab.
- Click "Add Pool" and enter your pool information in the below format.
- If you have multiple X1s, you can then copy this pool information to all of them quickly using the "Sync Network" button.
Antpool Register!
Code:
Servers : stratum+tcp://stratum.antpool.com:3333
User : username.worker or username_worker - auto creates workers!
Password: anypassword
BTCGuild Register!User : username.worker or username_worker - auto creates workers!
Password: anypassword
Code:
Servers : stratum+tcp://stratum.btcguild.com:3333
User : username_worker
Password: anypassword
GHash IO Register!User : username_worker
Password: anypassword
Code:
Servers : stratum+tcp://us1.ghash.io:3333
User : username.worker - auto creates workers!
Password: anypassword
User : username.worker - auto creates workers!
Password: anypassword
5) Troubleshooting (top)
TBD as problems arise.
Legal disclaimer: This information is for general guidance and does not constitute expert advice. We are not responsible if you, your property or a third
party is injured or damaged as a result of any interaction with this information, and no warranty is provided. All text and images are covered by copyright.
6) Where to buy (top)
Jump to: