You misunderstand each other.
Give us TW access and I'll try to fix it for you
Topic: [Guide] Dogie's Comprehensive Technobit HEX4M [HD] (Read 9761 times)
Interestingly it is not an option to disable.
Disable HEXM reset code (cgminer seting) via web and try again
Disable HEXM reset code (cgminer seting) via web and try again
Loshia and Martin have both offered to TW in and check it out as well. I will try that next and see how far we get.
Thank you for the help.
Thank you for the help.
If all of them is checked, then last resort is RMA 
If all of them is checked, then last resort is RMA
Now it sort of starts and then disables the miner.
With the Hex is was working fine I did nothing to it and it stopped.
I have hooked it up to a windows system it sees the miner. I just dont want to set it up on that one as it runs an array of Scrypt miners.
Here is what I get on the TP-Link again.
I have hooked it up to a windows system it sees the miner. I just dont want to set it up on that one as it runs an array of Scrypt miners.
Here is what I get on the TP-Link again.
Of course you can always switch back to previous version of TPLINK firmware that work before
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
Of course you can always switch back to previous version of TPLINK firmware that work before
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
For Rpi, you need to apply patch then compile the cgminer, it's easy even for windows user like me
So close. Now I have a Zombie. LOL
Hex4m is set for the handle USB error.
Remove the USB HUB Hex4m is set for the handle USB error.
Check again your cgminer configuration page.
Handle usb detect error as : set to hex4m
Handle usb detect error as : set to hex4m
Power off 12V of HEXM
Remove USB HEXM cable
Power on 12V of hexM
PLUG USB cable of HEXM into tplink without hub directly
and make sure your USB cable is OK
So close. Now I have a Zombie. LOL
Hex4m is set for the handle USB error.
Hex4m is set for the handle USB error.
Check again your cgminer configuration page.
Handle usb detect error as : set to hex4m
Handle usb detect error as : set to hex4m
Check again your cgminer configuration page.
Handle usb detect error as : set to hex4m
Handle usb detect error as : set to hex4m
Just power off HEXM board - unplug USB + 12V
Reboot tplink
power on 12V of HM board and finally plug USB cable
And you can remove hub also just plug board directly and make sure lsusb shows it
Reboot tplink
power on 12V of HM board and finally plug USB cable
And you can remove hub also just plug board directly and make sure lsusb shows it
Closer but not quite.
Rebooting the TP-Link and also SSH in and tried it manually.
Otherwise you need to restart cgminer
Or better just execute /usr/bin/fix_rc it will enable udevd and reboot tplink the all will be good
Rebooting the TP-Link and also SSH in and tried it manually.
It's a bit different this time. I changed the cable and the hub again.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
So it shall be mining if your udevd is started. I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
Otherwise you need to restart cgminerOr better just execute /usr/bin/fix_rc it will enable udevd and reboot tplink the all will be good
It's a bit different this time. I changed the cable and the hub again.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
So it shall be mining if your udevd is started. I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
Otherwise you need to restart cgminerOr better just execute /usr/bin/fix_rc it will enable udevd and reboot tplink the all will be good
It's a bit different this time. I changed the cable and the hub again.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I wish there was a RPi image for it. I have a ton of them. I will test it on a windows system.
Thank you for your help I do appreciate it.
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
Thank you for your help I do appreciate it.
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
Ok whatever you plug in tplink usb data port shall show in lsusb. It may bad usb cable, or just bad usb port of the tplink itself.I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Meanwhile just for the record you can plug your miner in windows. It shall show up like unknown usb device if all is ok. Just to see if miner usb connection is ok
I do, I have a solid power wart for the TP link.
I will double check the other cable though.
I will double check the other cable though.
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
board is not there and there is no USB hUB connected also
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
check your usb cable and try with another one. You need to have twio USB cables connected in TPLINK one for power and one for usb data
Sorry it's 4:30am here I am a bit slow.
dude in shell please type lsusb and post output can you?
dude in shell please type lsusb and post output can you?
Or better if you want/can pm me a TW id/pass so i can take a look
Or better if you want/can pm me a TW id/pass so i can take a look
All the chip LEDs are lighting up and blinking like it is hashing which is odd.
I have tried two hubs as well as directly into the TP-Link.
So it appears like usb issue cables hubs or..?
Board is missing
please type lsusb and post output
I have tried two hubs as well as directly into the TP-Link.
Got it in previous post.
Screenshot is there now.
Sorry about that. I brain cramped.
Screenshot is there now.
Sorry about that. I brain cramped.
Same as web user and pass
So it appears like usb issue cables hubs or..?
Board is missing
please type lsusb and post output
Got it in previous post.
Screenshot is there now.
Sorry about that. I brain cramped.
Screenshot is there now.
Sorry about that. I brain cramped.
Same as web user and pass
So it appears like usb issue cables hubs or..?
Board is missing
please type lsusb and post output
Got it in previous post.
Screenshot is there now.
Sorry about that. I brain cramped.
Screenshot is there now.
Sorry about that. I brain cramped.
Same as web user and pass
Same as web user and pass
Sorry about the confusion.
Got it.
Just noticed IPv4 broadcast is empty
---------------------------
It does not matter ....
once again screen -r via ssh will tell you what is wrong
pls post the output here
Got it.
It does sync the time properly with the network time.
Just noticed IPv4 broadcast is empty. I wonder if there was something there before?
----------------------Just noticed IPv4 broadcast is empty. I wonder if there was something there before?
screen -r?
What does it say?
Tplink shall be able to sync network time
What does it say?
Tplink shall be able to sync network time
Just noticed IPv4 broadcast is empty
---------------------------
It does not matter ....
once again screen -r via ssh will tell you what is wrong
pls post the output here
It does sync the time properly with the network time.
Just noticed IPv4 broadcast is empty. I wonder if there was something there before?
----------------------Just noticed IPv4 broadcast is empty. I wonder if there was something there before?
screen -r?
What does it say?
Tplink shall be able to sync network time
What does it say?
Tplink shall be able to sync network time
Just noticed IPv4 broadcast is empty
---------------------------
It does not matter ....
once again screen -r via ssh will tell you what is wrong
pls post the output here
It does sync the time properly with the network time.
Just noticed IPv4 broadcast is empty. I wonder if there was something there before?
Just noticed IPv4 broadcast is empty. I wonder if there was something there before?
screen -r?
What does it say?
Tplink shall be able to sync network time
What does it say?
Tplink shall be able to sync network time
screen -r?
What does it say?
Tplink shall be able to sync network time
What does it say?
Tplink shall be able to sync network time
I did check the other settings boxes and nothing was empty.
Also I have restarted the router and checked all sorts of settings. It was working well and just does not now so reflash and everything else I could think of I have tried. I am not used to this controller but I had it going before.
Also I have restarted the router and checked all sorts of settings. It was working well and just does not now so reflash and everything else I could think of I have tried. I am not used to this controller but I had it going before.
dogie mean to check all other miner(rockerbox, be200, A1, avalon, bitfury, nanofury, etc) setting page too.
If all checked then restart your router, probably dns problem.
If all checked then restart your router, probably dns problem.
How about the network setting? Did the setting right?
You can use ssh to see cgminer user interface, check what kind of alarm there(remove --quiet option on cgminer configuration page first).
I did check the other settings boxes and nothing was empty.
Also I have restarted the router and checked all sorts of settings. It was working well and just does not now so reflash and everything else I could think of I have tried. I am not used to this controller but I had it going before.
Also I have restarted the router and checked all sorts of settings. It was working well and just does not now so reflash and everything else I could think of I have tried. I am not used to this controller but I had it going before.
dogie mean to check all other miner(rockerbox, be200, A1, avalon, bitfury, nanofury, etc) setting page too.
If all checked then restart your router, probably dns problem.
If all checked then restart your router, probably dns problem.
dogie mean to check all other miner(rockerbox, be200, A1, avalon, bitfury, nanofury, etc) setting page too.
If all checked then restart your router, probably dns problem.
If all checked then restart your router, probably dns problem.
I just double checked all the configs have populated fields.
Does this setting look good? I cannot remember if I changed USB Detect errors box or not.
On all the pages? Sometimes some go blank when you flash new firmware. If you havent then I'm not sure.
Does this setting look good? I cannot remember if I changed USB Detect errors box or not.
They are. I did not change them.
Here is the Minion page.
Here is the Minion page.
On all the pages? Sometimes some go blank when you flash new firmware. If you havent then I'm not sure.
They are. I did not change them.
Here is the Minion page.
Here is the Minion page.
On all the pages? Sometimes some go blank when you flash new firmware. If you havent then I'm not sure.
They are. I did not change them.
Here is the Minion page.
Check all the values on all the miner config pages are filled.
Here is the Minion page.
I am using the TP-Link controller and I am suddenly getting this error.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
Check all the values on all the miner config pages are filled.
I am using the TP-Link controller and I am suddenly getting this error.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
Check all the values on all the miner config pages are filled.
Ok I have overcome that with several reboots of the TP-Link.
Now it is up but not mining when it did before. So dam odd.
Now it is up but not mining when it did before. So dam odd.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Reply was 'STATUS=S,When=1416098024,Code=70,Msg=CGMiner stats,Description=cgminer 4.6.1|STATS=0,ID=POOL0,Elapsed=92,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=256.00000000,Min Diff=256.00000000,Max Diff=256.00000000,Min Diff Count=62,Max Diff Count=62,Times Sent=2,Bytes Sent=155,Times Recv=9,Bytes Recv=5978,Net Bytes Sent=155,Net Bytes Recv=5978|STATS=1,ID=POOL1,Elapsed=92,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=1889.77719885,Min Diff=1889.77719885,Max Diff=2281.96347710,Min Diff Count=1,Max Diff Count=5,Times Sent=2,Bytes Sent=166,Times Recv=8,Bytes Recv=76360,Net Bytes Sent=166,Net Bytes Recv=76360|'
[STATUS] =>
(
[STATUS] => S
[When] => 1416098024
[Code] => 70
[Msg] => CGMiner stats
[Description] => cgminer 4.6.1
)
[STATS0] =>
(
[STATS] => 0
[ID] => POOL0
[Elapsed] => 92
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 256.00000000
[Min Diff] => 256.00000000
[Max Diff] => 256.00000000
[Min Diff Count] => 62
[Max Diff Count] => 62
[Times Sent] => 2
[Bytes Sent] => 155
[Times Recv] => 9
[Bytes Recv] => 5978
[Net Bytes Sent] => 155
[Net Bytes Recv] => 5978
)
[STATS1] =>
(
[STATS] => 1
[ID] => POOL1
[Elapsed] => 92
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 1889.77719885
[Min Diff] => 1889.77719885
[Max Diff] => 2281.96347710
[Min Diff Count] => 1
[Max Diff Count] => 5
[Times Sent] => 2
[Bytes Sent] => 166
[Times Recv] => 8
[Bytes Recv] => 76360
[Net Bytes Sent] => 166
[Net Bytes Recv] => 76360
)
cgminer: 4_5_0_9afd0a2
Reply was 'STATUS=S,When=1416098024,Code=70,Msg=CGMiner stats,Description=cgminer 4.6.1|STATS=0,ID=POOL0,Elapsed=92,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=256.00000000,Min Diff=256.00000000,Max Diff=256.00000000,Min Diff Count=62,Max Diff Count=62,Times Sent=2,Bytes Sent=155,Times Recv=9,Bytes Recv=5978,Net Bytes Sent=155,Net Bytes Recv=5978|STATS=1,ID=POOL1,Elapsed=92,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=1889.77719885,Min Diff=1889.77719885,Max Diff=2281.96347710,Min Diff Count=1,Max Diff Count=5,Times Sent=2,Bytes Sent=166,Times Recv=8,Bytes Recv=76360,Net Bytes Sent=166,Net Bytes Recv=76360|'
[STATUS] =>
(
[STATUS] => S
[When] => 1416098024
[Code] => 70
[Msg] => CGMiner stats
[Description] => cgminer 4.6.1
)
[STATS0] =>
(
[STATS] => 0
[ID] => POOL0
[Elapsed] => 92
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 256.00000000
[Min Diff] => 256.00000000
[Max Diff] => 256.00000000
[Min Diff Count] => 62
[Max Diff Count] => 62
[Times Sent] => 2
[Bytes Sent] => 155
[Times Recv] => 9
[Bytes Recv] => 5978
[Net Bytes Sent] => 155
[Net Bytes Recv] => 5978
)
[STATS1] =>
(
[STATS] => 1
[ID] => POOL1
[Elapsed] => 92
[Calls] => 0
[Wait] => 0.000000
[Max] => 0.000000
[Min] => 99999999.000000
[Pool Calls] => 0
[Pool Attempts] => 0
[Pool Wait] => 0.000000
[Pool Max] => 0.000000
[Pool Min] => 99999999.000000
[Pool Av] => 0.000000
[Work Had Roll Time] => false
[Work Can Roll] => false
[Work Had Expire] => false
[Work Roll Time] => 0
[Work Diff] => 1889.77719885
[Min Diff] => 1889.77719885
[Max Diff] => 2281.96347710
[Min Diff Count] => 1
[Max Diff Count] => 5
[Times Sent] => 2
[Bytes Sent] => 166
[Times Recv] => 8
[Bytes Recv] => 76360
[Net Bytes Sent] => 166
[Net Bytes Recv] => 76360
)
I am using the TP-Link controller and I am suddenly getting this error.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
[/code] Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
I am using the TP-Link controller and I am suddenly getting this error.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
Code:
[Firmware Version] => 20140922
cgminer: 4_5_0_9afd0a2
Socket connect failed: Connection refused
Anyone have a clue what to do to get this back up and running?
Ok I thought I had it but the error keeps coming.
I have varied the clock speed and voltage quite a bit. These are the other settings:
"hexminerm-pic-roll" : "90",
"hexminerm-hw-err-res" : "5",
"hexminerm-nonce-timeout-secs" : "2",
"hexminerm-chip-mask" : "15",
"hexminerm-voltage" : "780", < This one I have played with a lot.
"hexminerm-options" : "4:875", < And this one.
I am running this off windows with the CGminer version for HEX boards. I have run off a TPLink too.
Power supply is a Dell server PSU. Pushing out about 750 watts. Powering a single board.
I get tons of the nonce errors.
If you want to achieve maximum speed, do not change chipmask, voltage & options from default. You can play with other
"hexminerm-pic-roll" : "90",
"hexminerm-hw-err-res" : "10",
"hexminerm-nonce-timeout-secs" : "2",
"hexminerm-reset-below-threshold" : "25",
"hexminerm-chip-mask" : "15",
"hexminerm-voltage" : "820",
"hexminerm-options" : "4:1024",
My boards wont run at all at the default clock speed. Its pretty terrible.
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
What is your setting? All of them, not just 512/820 <== what is this anyway
(sorry, i am noob)What is your power supply? Brand & type
What is your controller? Tplink, Rpi, PC ....
Please post some picture, cgminer screenshot maybe
I have varied the clock speed and voltage quite a bit. These are the other settings:
"hexminerm-pic-roll" : "90",
"hexminerm-hw-err-res" : "5",
"hexminerm-nonce-timeout-secs" : "2",
"hexminerm-chip-mask" : "15",
"hexminerm-voltage" : "780", < This one I have played with a lot.
"hexminerm-options" : "4:875", < And this one.
I am running this off windows with the CGminer version for HEX boards. I have run off a TPLink too.
Power supply is a Dell server PSU. Pushing out about 750 watts. Powering a single board.
I get tons of the nonce errors.
My boards wont run at all at the default clock speed. Its pretty terrible.
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
What is your setting? All of them, not just 512/820 <== what is this anyway
(sorry, i am noob)What is your power supply? Brand & type
What is your controller? Tplink, Rpi, PC ....
Please post some picture, cgminer screenshot maybe
My boards wont run at all at the default clock speed. Its pretty terrible.
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
drop me PM with TW access I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
My boards wont run at all at the default clock speed. Its pretty terrible.
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
I can get them to run at 512/820 ... about 200 gh/s. Any faster clock speed and they die. I must be doing something wrong.
At 200 gh/s these aren't worth it...
I own one of these and have for a while, it's good but it took me a bit to get up and running (Marto took control and saved the day). I have it clocked down and it still pumps out 360ghash at a way better watt usage.
what settings are you using? and what wattage does it use? also, what should "hexminerm-pic-roll" be set at and what does this setting do exactly? I seem to be getting a lot of stale shares...
1016/830 makes it 90% stable @ 396-398 Gh But with ~4% rejects 
Should I change the nonce-timout settings?
Does this just vary per board? Because I am about to buy eight more. Is it still possible to overclock this board further?
I'll try 835 and 840 next since the board is still pretty cool not getting hot at all just a little warm
Nice design guys! Except you forgot to drill the holes in the bottom heatsink for the 4 thingy's that it stands on so its not standing very stable but I guess that's just because I got 1 of the 1st boards from the BA fiasco?
But with ~4% rejects Should I change the nonce-timout settings?Does this just vary per board? Because I am about to buy eight more. Is it still possible to overclock this board further?
I'll try 835 and 840 next since the board is still pretty cool not getting hot at all just a little warm
Nice design guys! Except you forgot to drill the holes in the bottom heatsink for the 4 thingy's that it stands on so its not standing very stable but I guess that's just because I got 1 of the 1st boards from the BA fiasco?
Hi,
Check if all collars are good connected .
then try 1016/820 or even 840
Check if all collars are good connected .
then try 1016/820 or even 840
Hey guys my hex4m has this particular problem:
it's timing out I've tried lower and higher values for the nonce-timout setting in cgminer nut this seems to be the best I can get out of it? Sometimes it runs smooth for a few minutes without the reset error and then it goes at around 400gh and every once in a while it will just give so many of the reset errors that it's hashrate drops down to avout 100gh for a minute or two.
I just used the cooling paste that was on the bottom of the freezer pro 7 but if this was overheating i should be able e to feel heat on the pcb around the chip and it's room temperature pretty much not hot at all...
anyone had similar problems?
it's timing out I've tried lower and higher values for the nonce-timout setting in cgminer nut this seems to be the best I can get out of it? Sometimes it runs smooth for a few minutes without the reset error and then it goes at around 400gh and every once in a while it will just give so many of the reset errors that it's hashrate drops down to avout 100gh for a minute or two.
I just used the cooling paste that was on the bottom of the freezer pro 7 but if this was overheating i should be able e to feel heat on the pcb around the chip and it's room temperature pretty much not hot at all...
anyone had similar problems?
Dogie's Miner Setup Guides:
Nicely formatted version available at dogiecoin.com!
Contents:
0a) What to Expect
0b) What You Need
1) Powering
2) Cooling
3a) Configuration (TL-MR3020)
3b) Configuration (Windows PC)
4) Troubleshooting
5) Where to buy
0a) What to Expect (top)
Technobit's HEX4M utilises four of BlackArrow's 28nm ASICs on a single, large PCB. Top side heatsinks are not provided as standard and an external
controller in the form of TP-LINK TL-MR3020 or Windows PC is required.
0b) What You Need (top)
You will need a few accessories, a power supply, four heatsinks and a controller to get started. I recommend getting the controller from Technobit as
they will preload it with the latest firmware.
Click your flag to find everything you need to get started at Amazon!
1) Powering (top)
HEX4Ms do not come with a power supply, and you will need a typical computer PSU with 2xPCI-E 6 pin power connectors. We also need to tell the PSU to
always be on, as there isn't a motherboard to do this. Cut a paper clip into a U and insert it into the green wire and either black wire to the side of the
green wire. Tape it up for safety. The power supply will now be controlled by its switch on the rear socket.
2) Cooling (top)
An aluminium heatsink covers the entire backside of the board to provide structure and keep board temperatures down, and is cooled by a single 120mm
heatsink. The minion chips each require a Arctic Freezer 7 Pro heatsink, or socket 1150 heatsink. You will have to be careful with compatibility due to how
to backside heatsink interferes with how the chip's backplate would usually be installed.
3a) Configuration (TL-MR3020) (top)
An external controller is required which can either be a TP-LINK TL-MR3020 router or a Windows based PC.
Wiring:
Using a modified TP Link MR3020
Alternative Subnet Change:
Antpool Register!
3b) Configuration (Windows PC) (top)
An external controller is required which can either be a TP-LINK TL-MR3020 router or a Windows based PC.
Wiring:
Using a Windows based PC
Antpool Register!
4) Troubleshooting (top)
Legal disclaimer: This information is for general guidance and does not constitute expert advice. We are not responsible if you, your property or a third
party is injured or damaged as a result of any interaction with this information, and no warranty is provided. All text and images are covered by copyright.
5) Where to buy (top)
Nicely formatted version available at dogiecoin.com!
Contents:
0a) What to Expect
0b) What You Need
1) Powering
2) Cooling
3a) Configuration (TL-MR3020)
3b) Configuration (Windows PC)
4) Troubleshooting
5) Where to buy
0a) What to Expect (top)
Technobit's HEX4M utilises four of BlackArrow's 28nm ASICs on a single, large PCB. Top side heatsinks are not provided as standard and an external
controller in the form of TP-LINK TL-MR3020 or Windows PC is required.
| Chips | 4x BlackArrow Minion |
| Hashrate | 400GH |
| Rated Voltage | 12V |
| Rated Current | 36A |
| Power.Consumption | ~430W |
0b) What You Need (top)
You will need a few accessories, a power supply, four heatsinks and a controller to get started. I recommend getting the controller from Technobit as
they will preload it with the latest firmware.
Click your flag to find everything you need to get started at Amazon!
1) Powering (top)
HEX4Ms do not come with a power supply, and you will need a typical computer PSU with 2xPCI-E 6 pin power connectors. We also need to tell the PSU to
always be on, as there isn't a motherboard to do this. Cut a paper clip into a U and insert it into the green wire and either black wire to the side of the
green wire. Tape it up for safety. The power supply will now be controlled by its switch on the rear socket.
2) Cooling (top)
An aluminium heatsink covers the entire backside of the board to provide structure and keep board temperatures down, and is cooled by a single 120mm
heatsink. The minion chips each require a Arctic Freezer 7 Pro heatsink, or socket 1150 heatsink. You will have to be careful with compatibility due to how
to backside heatsink interferes with how the chip's backplate would usually be installed.
3a) Configuration (TL-MR3020) (top)
An external controller is required which can either be a TP-LINK TL-MR3020 router or a Windows based PC.
Wiring:
- Plug in an ethernet cable from the TL-MR3020 to you router.
- Plug a mini usb cable from the TL-MR3020 to the mains power adapter.
- Plug a mini usb cable from the HEX4M to the TL-MR3020.
- Plug in two PCI-E connectors into the HEX4M.
Using a modified TP Link MR3020
- Power on as above.
- Flash Technobit's latest custom WRT firmware (or purchase their preflashed TL-MR3020.
- Make sure or your router's subnet is 0, ie 192.168.0.x. If not then change it to 0, this is just temporary. ***If this is not possible, see below***
- Using a browser, navigate to 192.168.0.99 - this goes to the MR3020's configuration page.
- Login using "root" as the username and password.
- Navigate to Network -> Interfaces -> LAN -> Edit.
- Change protocol to DHCP and click "Save & Apply".
- Using a browser, navigate to your router and find the IP it has assigned the MR3020 and navigate to that IP.
- Navigate to the page CGminer -> Configuration. Enter your pool information in the below format.
- You can then change your router subnet back to whatever you are used to using.
Alternative Subnet Change:
- Unplug your computer from all internet sources.
- Plug in an ethernet cable from the MR3020 to your computer.
- Navigate to Control Panel -> Network and Sharing Centre -> Change Adapter Settings.
- Right click on your ethernet adapter -> Properties.
- Click on "Internet Protocol Version 4" and click properties.
- Select "Use the following IP address" and enter the following:
- IP Address: 192.168.0.1, Subnet Mask: 255.255.255.0, Default Gateway: 192.168.0.99.
- Plug in an ethernet cable from the MR3020 to you router.
- Restart the configuration instructions as above.
Antpool Register!
Code:
Servers : stratum.antpool.com:3333
User : username.worker or username_worker - auto creates workers!
Password: anypassword
BTCGuild Register!User : username.worker or username_worker - auto creates workers!
Password: anypassword
Code:
Servers : stratum.btcguild.com:3333
User : username_worker
Password: anypassword
GHash IO Register!User : username_worker
Password: anypassword
Code:
Servers : us1.ghash.io:3333
User : username.worker - auto creates workers!
Password: anypassword
User : username.worker - auto creates workers!
Password: anypassword
3b) Configuration (Windows PC) (top)
An external controller is required which can either be a TP-LINK TL-MR3020 router or a Windows based PC.
Wiring:
- Plug a mini usb cable from the HEX4M to your Windows PC.
- Plug in two PCI-E connectors into the HEX4M.
Using a Windows based PC
- Windows will try and install its own drivers. Wait until it finishes.
- Download the Zadig tool and run it.
- Choose the HEX4M and "WinUSB". Click install driver.
- Once installed, you may have to restart your PC.
- Download this specific version of cgminer and extract it.
- Edit cgminer.conf using notepad, with your pool and miner information in it, an example as below.
- Run cgminer.exe to start mining.
Antpool Register!
Code:
Servers : stratum.antpool.com:3333
User : username.worker or username_worker - auto creates workers!
Password: anypassword
BTCGuild Register!User : username.worker or username_worker - auto creates workers!
Password: anypassword
Code:
Servers : stratum.btcguild.com:3333
User : username_worker
Password: anypassword
GHash IO Register!User : username_worker
Password: anypassword
Code:
Servers : us1.ghash.io:3333
User : username.worker - auto creates workers!
Password: anypassword
User : username.worker - auto creates workers!
Password: anypassword
4) Troubleshooting (top)
| Problem | Solution |
| My.power.supply's.cables.are.braided.or.aren't.color.coded | - See below diagram for pin-outs. |
Legal disclaimer: This information is for general guidance and does not constitute expert advice. We are not responsible if you, your property or a third
party is injured or damaged as a result of any interaction with this information, and no warranty is provided. All text and images are covered by copyright.
5) Where to buy (top)
Jump to: