Update to 4.6 may help.
Make sure 5 pin usb is seated properly on the board the red wire is facing away from the board.
If using ATX make sure whatever means you are shorting it is still good.
I have picked up several early version boards from folks that can’t get them up or that did not understand the process to get them working.
I use a similar like cable on the boards I have. Please note I have never bought anything from Aliexpress I am working around an internet filter at my job and it lets me go here and not Ebay.
http://www.aliexpress.com/store/product/USB-A-female-Panel-Mount-extension-Cable-for-PCI-or-Front-Panel-Mount/601043_1009987148.html
Good Luck
Topic: HashFast BabyJet users thread - page 2. (Read 69023 times)
I will have access to on one Monday. I let a friend borrow it and will grab it from him when I see him on Monday.
Mmk with the board powered on check voltages across the 12V pins on the 6pin connector to gnd(on the 6pin connector). Also what type of psu are you using to power them: atx power supply or a server psu w/breakout board?
I will have access to on one Monday. I let a friend borrow it and will grab it from him when I see him on Monday.
Also, My miner is down because of my RPi. So i have decided to try to host with one of my laptops. I am running windows at the moment, and have used zadig to get the correct USB driver (I think). When I try to run CGminer i get this error:
Any help would be much appreciated. My babyjet has been dead for about a week now.
It's telling you what's wrong. 12v supply is bad.Any help would be much appreciated. My babyjet has been dead for about a week now.
I replaced all my connections and replaced the power supply with an identical one. And both my boards are given me the same error message. Unless they both died at once, which I think is highly unlikely. Is there anything in the config files that I may not have set up right to give me this error? This is my first time setting up CGminer out side of MinePeon.
do you have access to a digital multimeter?
Also, My miner is down because of my RPi. So i have decided to try to host with one of my laptops. I am running windows at the moment, and have used zadig to get the correct USB driver (I think). When I try to run CGminer i get this error:
https://i.imgur.com/LuP3ogl.png
Any help would be much appreciated. My babyjet has been dead for about a week now.
It's telling you what's wrong. 12v supply is bad.https://i.imgur.com/LuP3ogl.png
Any help would be much appreciated. My babyjet has been dead for about a week now.
I replaced all my connections and replaced the power supply with an identical one. And both my boards are given me the same error message. Unless they both died at once, which I think is highly unlikely. Is there anything in the config files that I may not have set up right to give me this error? This is my first time setting up CGminer out side of MinePeon.
Also, My miner is down because of my RPi. So i have decided to try to host with one of my laptops. I am running windows at the moment, and have used zadig to get the correct USB driver (I think). When I try to run CGminer i get this error:
Any help would be much appreciated. My babyjet has been dead for about a week now.
It's telling you what's wrong. 12v supply is bad. Any help would be much appreciated. My babyjet has been dead for about a week now.
Also, My miner is down because of my RPi. So i have decided to try to host with one of my laptops. I am running windows at the moment, and have used zadig to get the correct USB driver (I think). When I try to run CGminer i get this error:
https://i.imgur.com/LuP3ogl.png
Any help would be much appreciated. My babyjet has been dead for about a week now.
https://i.imgur.com/LuP3ogl.png
Any help would be much appreciated. My babyjet has been dead for about a week now.
Does anyone know if the original HF image will work on the RPi anymore? It looks like in its start-up code it references startup.hashfast.com which i think is now redirected to their home page. If so, would anyone mind making an image of their working RPi image and post it for others to use as a new base when your SD card shits out?
Thank you so much!!
Thank you so much!!
Found it via IRC
[3:11pm] <10+capa66_> Blazedout419: https://mega.co.nz/#!DRghBC5Q!HM2eAtRQK_z7NMWHsyxbyKPWCnRUVA5NQJXinWUDU7g
[3:11pm] <04Blazedout419> Oh yay
[3:11pm] <04Blazedout419> you get the reward too
[3:11pm] <10+capa66_> Blazedout419: https://mega.co.nz/#!DRghBC5Q!HM2eAtRQK_z7NMWHsyxbyKPWCnRUVA5NQJXinWUDU7g
[3:11pm] <04Blazedout419> Oh yay
[3:11pm] <04Blazedout419> you get the reward too
Does it update itself to the latest version still?
Found it via IRC
[3:11pm] <10+capa66_> Blazedout419: https://mega.co.nz/#!DRghBC5Q!HM2eAtRQK_z7NMWHsyxbyKPWCnRUVA5NQJXinWUDU7g
[3:11pm] <04Blazedout419> Oh yay
[3:11pm] <04Blazedout419> you get the reward too
[3:11pm] <10+capa66_> Blazedout419: https://mega.co.nz/#!DRghBC5Q!HM2eAtRQK_z7NMWHsyxbyKPWCnRUVA5NQJXinWUDU7g
[3:11pm] <04Blazedout419> Oh yay
[3:11pm] <04Blazedout419> you get the reward too
$10 in BTC to the first person who gives me a working link to it...!
I can not seem to find a working link for the rasp pi image for my Baby Jet...If anyone has one it would be much appreciated!
at stock 500mhz its about 438 and at 550mhz 450 and at 600mhz I think its 490 and that's with a kill O Watt on it.
around 500w ( 498)
Hi, what is the power consumation at the wall of HashFast Baby Jet running standard config at 400GHs?
Thanks in advance W_M
Thanks in advance W_M
Anyone asked HF what they have done with the PSU cables, ? I doubt they got the PSU without them, and since they were obviously planning on uprading their BJ they must have kept them.
I wouldn't mind paying shipping to whoever inherited of them.
I wouldn't mind paying shipping to whoever inherited of them.
anyone know how run the babyjet psu (seasonic) outside the bj's case ?
thanx in advance
thanx in advance
Not only the normal Green to Black jumper but also these damm seasonics require a super secret jumper, the details of which are not even revealed on the sesonic website.
Seasonic must have countless returns on their power supplies that are in fact TOTALLY FINE because their customers only do the green-black jumpering for testing AS THEY ARE INSTRUCTED TO DO BY SEASONIC via the website.
I don't understand Seasonics thinking and waste of everyone's time...
thanx you should be able to take it out of the case you might need to buy cables from ebay or seasonic to use it on a pc for a power supply.
thanx ! ( sorry for the one month lag !
For those that are trying to salvage their BJ PSU like myself, BTOS Tech has them in stock. You can preview the cables here: http://www.btostech.com/store/pc/Seasonic-Modular-Cables-c79.htm.
George Lai at that BTOS was extremely helpful and I was able to get full sets of cables for both my SS-1000XP. As for special jumpering, I disagree. I have one of my SS-1000XPs jumpered using the black/green pin running 2 Antminer S1s atm.
George Lai at that BTOS was extremely helpful and I was able to get full sets of cables for both my SS-1000XP. As for special jumpering, I disagree. I have one of my SS-1000XPs jumpered using the black/green pin running 2 Antminer S1s atm.
Jump to: