MultiMiner: Any Miner, Any Where, on Any Device (Free, Open Source, Cross Platform) - page 67.

nwoolls

hero member

Activity: 840

Merit: 1002

Quote from: Aurum on March 17, 2014, 01:08:10 PM

I just tried again and it didn't work. I right-clicked an AntMiner S1 in MuM 2.8.1 and chose the 2nd pool. Logged into the pool account and no hashing has appeared in the last 10 minutes. All hashing is still going to pool 1.

Make sure that your configuration for your AntMiner has a W: prefix for api-allow, e.g.:

Code:

option api_allow 'W:127.0.0.1,W:192.168.0.0/24'

Otherwise the API access is read-only.

Quote from: Aurum on March 17, 2014, 01:08:10 PM

If BitMain loaded bfgminer in its firmware would that give you full control Huh

Nope.

DocGonzzo

newbie

Activity: 27

Merit: 0

Working on the RPi, thank you Nate
http://i1373.photobucket.com/albums/ag388/richmondimage/ScreenShot2014-03-17at23131PM_zps3de0bdeb.png

Aurum

sr. member

Activity: 453

Merit: 250

dfgfdgfdg

Quote from: nwoolls on March 17, 2014, 12:35:48 PM

Quote from: Aurum on March 17, 2014, 08:58:54 AM

Is it possible to get MuM to behave for AntMiner S1 like it does BitFury or BFL Single Huh

No, they are fundamentally different devices. One I have full control over and one I only have API access to.

Quote from: Aurum on March 17, 2014, 08:58:54 AM

I tried right-clicking on an AntMiner S1 network device and switching to another coin but it never switches. I tried it with and without restarting. Is there something in the configuration I might be missing Huh

I'm not sure what you mean by another coin - do you mean another pool? The only thing you can do with Network Devices currently is switch them between the pools you have configured in their web UI and restart them. I just tried with my AntMiner S1 and MultiMiner 2.8 and had no problem switching pools (no need to restart, just wait 20-30s or so).

I just tried again and it didn't work. I right-clicked an AntMiner S1 in MuM 2.8.1 and chose the 2nd pool. Logged into the pool account and no hashing has appeared in the last 10 minutes. All hashing is still going to pool 1.

If BitMain loaded bfgminer in its firmware would that give you full control Huh

nwoolls

hero member

Activity: 840

Merit: 1002

Quote from: Aurum on March 17, 2014, 08:58:54 AM

Is it possible to get MuM to behave for AntMiner S1 like it does BitFury or BFL Single Huh

No, they are fundamentally different devices. One I have full control over and one I only have API access to.

Quote from: Aurum on March 17, 2014, 08:58:54 AM

I tried right-clicking on an AntMiner S1 network device and switching to another coin but it never switches. I tried it with and without restarting. Is there something in the configuration I might be missing Huh

I'm not sure what you mean by another coin - do you mean another pool? The only thing you can do with Network Devices currently is switch them between the pools you have configured in their web UI and restart them. I just tried with my AntMiner S1 and MultiMiner 2.8 and had no problem switching pools (no need to restart, just wait 20-30s or so).

nwoolls

hero member

Activity: 840

Merit: 1002

Quote from: jmordica on March 17, 2014, 09:41:26 AM

@nwoolls can you support this arg in bfgminer for gridseed (voltage=1) and more frequencies?

https://bitcointalksearch.org/topic/gridseed-5-chip-usb-miner-voltage-mod-519112

AFAIK it already supports all of the frequencies that are in the reference documentation and source code from GridSeed. There's still more to do before BFGMiner 4.0 is release (like BTC and Dual Mode support) so I'll re-evaluate and see where the reference source and documentation is on that. I want to try to stick to the official docs.

jmordica

member

Activity: 99

Merit: 10

@nwoolls can you support this arg in bfgminer for gridseed (voltage=1) and more frequencies?

https://bitcointalksearch.org/topic/gridseed-5-chip-usb-miner-voltage-mod-519112

Thanks!

Aurum

sr. member

Activity: 453

Merit: 250

dfgfdgfdg

Is it possible to get MuM to behave for AntMiner S1 like it does BitFury or BFL Single Huh

I tried right-clicking on an AntMiner S1 network device and switching to another coin but it never switches. I tried it with and without restarting. Is there something in the configuration I might be missing Huh

hoop

legendary

Activity: 1524

Merit: 1001

NOBT - WNOBT your saving bank◕◡◕

can i run this on VPS

jmordica

member

Activity: 99

Merit: 10

**EDIT** Oops, posted this in the wrong thread. It is now here: https://bitcointalksearch.org/topic/m.5738579

brooklynite

sr. member

Activity: 266

Merit: 250

Quote from: nwoolls on March 14, 2014, 03:41:51 PM

Quote from: brooklynite on March 14, 2014, 02:14:05 PM

This usually happens after the "The AMD driver has crashed and successfully recovered" note. When I logged in remotely there was a Windows 8.1 message that the program has recovered from a crash and if I want to report it to microsoft. CGMiner runs fine by the way.

Logged in remotely how? Are you using RDP or VNC? GPU mining does not work via RDP and you will end up with very odd results as the full AMD driver will not load.

Edit: Try posting a screenshot or a video of the problem. That may help. The Start button is disabled if you don't have a valid configuration - e.g. no devices or your devices have no selected coin configuration or your configurations have no pools etc.

I log in via tightvnc. This problem is sporadic and there is no way to fix it other than many many reboots and basically it randomly starts again.

It just happened again after I shut the rig down, move the cards a bit to allow for air flow and BAM its gone weird again. Not starting. CGMiner works so this is a software glitch with bfgminer. Again if I knew how to delete the BIN files it would work I bet. CGMiner always works better when the delete *.bin is in the .bat file.

Dont know how the screen shot can be of any clue but here it is:

jmordica

member

Activity: 99

Merit: 10

I see your post here: https://github.com/gridseed/cgminer-3.1.1-GC3355-SV/issues/1

Your instructions are:

Quote

You can hash them at the same time if you launch with --set-device dualminer:dual_mode=1

Specifically, launch the BTC instance first (no dual_mode arg required but okay to add), launch the LTC instance second, dual_mode arg required.

Are you just referring to bfgminer or MultiMiner as well? If MultiMiner supports this, can you explain how to achieve this in the app?

Thanks!

jmordica

member

Activity: 99

Merit: 10

Does MultiMiner/bfgminer PR 4.0 support dual mining with gridseed 5-chip? If so, how is this done? Would I just run 2 instances of MultiMiner?

Thanks.

ofeefee

legendary

Activity: 1023

Merit: 1001

Tokenize Fantasy Sports

Quote from: ofeefee on March 15, 2014, 08:41:39 PM

Quote from: ofeefee on March 15, 2014, 08:38:04 PM

Quote from: nwoolls on March 15, 2014, 08:34:04 PM

Quote from: ofeefee on March 15, 2014, 07:35:55 PM

i have 8 dualminer usbs and trying to get them to mine in MultiMiner. I downloaded bfgminer with gridseed support, and have it setup so that this is the bfgminer that is used.

I have been mining with the dualminer software, closed, it, and installed the FTDI drivers, and all the com ports show that it's using this driver. I'm on the latest MM, but even after scan hardware, they are not detected. When I do "scan hardware" my usbs blink off and on like they are being scanned, but don't see them.

Something i'm missing?

Add --scrypt under Settings > Advanced miner settings > Hardware scan.

was just about to post an update, have bfgminer running in cli mode, and it detected them and appears to be hashing, but thanks, adding that now

brilliant that did it!

not sure if it matters, but mine show usb, dual rs2320hs a, and driver dualminer, if anyone else is trying and needs to compare.

Thanks, all in one place now

ofeefee

legendary

Activity: 1023

Merit: 1001

Tokenize Fantasy Sports

Quote from: ofeefee on March 15, 2014, 08:38:04 PM

Quote from: nwoolls on March 15, 2014, 08:34:04 PM

Quote from: ofeefee on March 15, 2014, 07:35:55 PM

i have 8 dualminer usbs and trying to get them to mine in MultiMiner. I downloaded bfgminer with gridseed support, and have it setup so that this is the bfgminer that is used.

I have been mining with the dualminer software, closed, it, and installed the FTDI drivers, and all the com ports show that it's using this driver. I'm on the latest MM, but even after scan hardware, they are not detected. When I do "scan hardware" my usbs blink off and on like they are being scanned, but don't see them.

Something i'm missing?

Add --scrypt under Settings > Advanced miner settings > Hardware scan.

was just about to post an update, have bfgminer running in cli mode, and it detected them and appears to be hashing, but thanks, adding that now

brilliant that did it!

ofeefee

legendary

Activity: 1023

Merit: 1001

Tokenize Fantasy Sports

Quote from: nwoolls on March 15, 2014, 08:34:04 PM

Quote from: ofeefee on March 15, 2014, 07:35:55 PM

i have 8 dualminer usbs and trying to get them to mine in MultiMiner. I downloaded bfgminer with gridseed support, and have it setup so that this is the bfgminer that is used.

I have been mining with the dualminer software, closed, it, and installed the FTDI drivers, and all the com ports show that it's using this driver. I'm on the latest MM, but even after scan hardware, they are not detected. When I do "scan hardware" my usbs blink off and on like they are being scanned, but don't see them.

Something i'm missing?

Add --scrypt under Settings > Advanced miner settings > Hardware scan.

was just about to post an update, have bfgminer running in cli mode, and it detected them and appears to be hashing, but thanks, adding that now

nwoolls

hero member

Activity: 840

Merit: 1002

Quote from: ofeefee on March 15, 2014, 07:35:55 PM

i have 8 dualminer usbs and trying to get them to mine in MultiMiner. I downloaded bfgminer with gridseed support, and have it setup so that this is the bfgminer that is used.

I have been mining with the dualminer software, closed, it, and installed the FTDI drivers, and all the com ports show that it's using this driver. I'm on the latest MM, but even after scan hardware, they are not detected. When I do "scan hardware" my usbs blink off and on like they are being scanned, but don't see them.

Something i'm missing?

Add --scrypt under Settings > Advanced miner settings > Hardware scan.

ofeefee

legendary

Activity: 1023

Merit: 1001

Tokenize Fantasy Sports

i have 8 dualminer usbs and trying to get them to mine in MultiMiner. I downloaded bfgminer with gridseed support, and have it setup so that this is the bfgminer that is used.

I have been mining with the dualminer software, closed, it, and installed the FTDI drivers, and all the com ports show that it's using this driver. I'm on the latest MM, but even after scan hardware, they are not detected. When I do "scan hardware" my usbs blink off and on like they are being scanned, but don't see them.

Something i'm missing?

nwoolls

hero member

Activity: 840

Merit: 1002

Quote from: nwoolls on March 15, 2014, 01:38:01 PM

Quote from: Raptor2213 on March 15, 2014, 08:38:07 AM

As usual, I spoke too soon, still getting double-crashes (both MultiMiner and BFGMiner at the same time). Doesn't appear to just be a BFGminer issue.

Again...please report this in either the BFGMiner thread or the BFGMiner issues on Github. This is not an issue with MultiMiner. MultiMiner is throwing an error because BFGMiner crashed.

Version 2.8.3 fixes the error message you were seeing in MultiMiner (basically MultiMiner couldn't communicate with the crashed BFGMiner instance).

124C41

sr. member

Activity: 308

Merit: 250

EVERYTHING YOU CAN IMAGINE IS REAL

add commas to your variables like so

Quote from: Alfred0211 on March 15, 2014, 07:45:54 AM

Quote from: 124C41 on March 15, 2014, 03:13:42 AM

Quote from: Alfred0211 on March 15, 2014, 01:34:39 AM

Hi
First of thanks for creating this usefull mining software

I can't seem to figure out though how I'm suppost to give each of my graphics cards individually different parameters (thread concurrency, intensity etc.) because I run a couple of different AMD gpu's Huh

Any help would be great Cheesy

Thanks in advance!

Click 'advanced miner settings'

Yes but if I use that it applies it to all my gpus at once, problem is I have 2 r9 280x's and 2 of the 7950's and they each need different parameters.
I tried ticking a gpu or highlighting it and then changing it but it still changes all gpu settings at once Huh

nwoolls

hero member

Activity: 840

Merit: 1002

Quote from: jmordica on March 15, 2014, 01:42:39 AM

This brings up the question. Will the ubuntu version of multiminer work with gridseed 5 chip devices yet? I guess if bfgminer can be installed then yes but what about the drivers and how would bfgminer be installed if it isn't released yet?

You'll need to compile BFGMiner from my branch with GridSeed support but yes it should work just fine.

Topic: MultiMiner: Any Miner, Any Where, on Any Device (Free, Open Source, Cross Platform) - page 67. (Read 827336 times)