nobody can read the trashcan except moderators/admins.
Too bad, I bet it's more interesting than some posts
Topic: Newbie restrictions - page 207. (Read 442111 times)
Too bad, I bet it's more interesting than some posts
I would agree, but also, there are forums I cannot read as a newbie, that I have been sent from a moderator when I attempted to ask for help from the bitcoin community. Are there many that are locked?
There are no forums that are unreadable by just newbies, nobody can read the trashcan except moderators/admins.
It's in the OP.
Due to a mass of trolling, only established posters are able to post in non-newbie sections. You are considered "established" if you have spent 4 hours online and have made 5 posts.
If you have really good posts, you can post a request for preemptive whitelisting in the appropriate topic.
Also:
- You must have made one post in order to send PMs.
- You need 10 posts to put a link in your signature.
Note that it may take up to 10 minutes for your PM or posting permissions to be granted.
If you have really good posts, you can post a request for preemptive whitelisting in the appropriate topic.
Also:
- You must have made one post in order to send PMs.
- You need 10 posts to put a link in your signature.
Note that it may take up to 10 minutes for your PM or posting permissions to be granted.
4 hours waiting online and 5 posts is not something difficult to achieve.
It's in the OP.
Due to a mass of trolling, only established posters are able to post in non-newbie sections. You are considered "established" if you have spent 4 hours online and have made 5 posts.
If you have really good posts, you can post a request for preemptive whitelisting in the appropriate topic.
Also:
- You must have made one post in order to send PMs.
- You need 10 posts to put a link in your signature.
Note that it may take up to 10 minutes for your PM or posting permissions to be granted.
If you have really good posts, you can post a request for preemptive whitelisting in the appropriate topic.
Also:
- You must have made one post in order to send PMs.
- You need 10 posts to put a link in your signature.
Note that it may take up to 10 minutes for your PM or posting permissions to be granted.
Would be useful to have a way to PM without the newbie restriction. (Especially because ABCPool only allows contact via bitcointalk.)
^+1 
Thank you for setting up this great forum. The rules and setup make a lot of sense. I look forward to posting more. I just set up a security on GLBSE that will IPO on August 16th. I'll post more info soon.
Great forum I agree.
3 hours 54 minutes and 4 posts left for activation.
I just need half an hour now =)
3 hours 54 minutes and 4 posts left for activation.
Hi everybody!
Hi all
Now it makes sense why I couldn't post on the other forum sections.
Will try to fix this.
Will try to fix this.
I need only send a private message to someone, can you activate my account?
I do not have much to say, I prefer to read what others write, but sometimes it needs to contact someone via PM
I do not have much to say, I prefer to read what others write, but sometimes it needs to contact someone via PM
Hi! where I should ask for support on this forum?
I can't reply nor post on almost all threads in the forum.
Thanks.
I can't reply nor post on almost all threads in the forum.
Thanks.
You were a newbie at the time of posting this, but you should be free of those restrictions now (4 hours, 5 posts).
Hi! where I should ask for support on this forum?
I can't reply nor post on almost all threads in the forum.
Thanks.
I can't reply nor post on almost all threads in the forum.
Thanks.
t
Finally done with the damn time requirement.
Thank you so much. I will also make sure to take some time and read the stickies.
You need to have one post, so you should be able to now.
It's mentioned in the sticky. https://bitcointalksearch.org/topic/newbie-restrictions-15958
It's mentioned in the sticky. https://bitcointalksearch.org/topic/newbie-restrictions-15958
Hi,
This will be a stupid newbie question, but how do you send a PM on this form. I found the member I need to contact (as per their support instructions) but cannot find a PM link on their profile.
Can someone please point me in the right direction?
Thanks,
DT
This will be a stupid newbie question, but how do you send a PM on this form. I found the member I need to contact (as per their support instructions) but cannot find a PM link on their profile.
Can someone please point me in the right direction?
Thanks,
DT
Jump to: