Is there a ready compiled version of this for linux?
I'm working with a mining os which is pretty closed.
Topic: Open Source XPM (Primecoin) GPU Miner & Pool xpmforall.org - page 25. (Read 110139 times)
I also noticed that you sent less coins today than usual...yesterday 48 coins, the day before 44 and today barely 36...Are there some problems with the pool?
for 13 hours 2 coins in all
2 coins in 13 hours? It looks that you use target="10" in config.txt.. what GPUs you use? Also you can post your XPM address. why the pool calculator does not correspond to the reality I have a speed of cpd 25 and should be 6-7 coins per hour and on the case itself 0.3 coins in one hour
Pool is PPLNS - pay per last N shares. In details, xpmforall and coinsforall calculate hashrate using number of last shares from ~1.5 hours (1 hour 30 minutes). How much time you stay at pool ?why the pool calculator does not correspond to the reality I have a speed of cpd 25 and should be 6-7 coins per hour and on the case itself 0.3 coins in one hour
Pool is PPLNS - pay per last N shares. In details, xpmforall and coinsforall calculate hashrate using number of last shares from ~1.5 hours (1 hour 30 minutes). How much time you stay at pool ?
why the pool calculator does not correspond to the reality I have a speed of cpd 25 and should be 6-7 coins per hour and on the case itself 0.3 coins in one hour
If anybody using RX 570? How much cpd do you get?
0.42cpd
If you would like to share the settings i will be glad to donate some coins to your address.
send me a pm.
Getting only 0.27 cpd on RX 570 4GB... What should I change?
I just downloaded the client and put my address... Not sure what should I do.
I just downloaded the client and put my address... Not sure what should I do.
If anybody using RX 570? How much cpd do you get?
0.39-0.4
If anybody using RX 570? How much cpd do you get?
0.42cpd
Thanks guys. Does it matter 4 or 8 Gb on board?
And second question – is somebody tried to use RX550 card?
If anybody using RX 570? How much cpd do you get?
0.42cpd
If you would like to share the settings i will be glad to donate some coins to your address.
u get the same speed as you would from 2 290x's
That is 0.42 CDP per core.
Is that low or normal?
too low. i have 0.42cpd but my card are 290 (not x) and it it downclocked to 800MHz.
at stock frequency 290x shoult put more than 0.5cpd.
try old xpmclient9.4.1
Ill try. Thanks!
0.47 was best i got but later on its coming down to 0.42.
Have you guys ever seen a 290(x) with a single 8-pin power connector only?
295x2 = 2x 290x with two 8-pins only.
u get the same speed as you would from 2 290x's
That is 0.42 CDP per core.
Is that low or normal?
too low. i have 0.42cpd but my card are 290 (not x) and it it downclocked to 800MHz.
at stock frequency 290x shoult put more than 0.5cpd.
try old xpmclient9.4.1
Ill try. Thanks!
0.47 was best i got but later on its coming down to 0.42.
u get the same speed as you would from 2 290x's
That is 0.42 CDP per core.
Is that low or normal?
too low. i have 0.42cpd but my card are 290 (not x) and it it downclocked to 800MHz.
at stock frequency 290x shoult put more than 0.5cpd.
try old xpmclient9.4.1
If anybody using RX 570? How much cpd do you get?
0.42cpd
If anybody using RX 570? How much cpd do you get?
0.39-0.4
Why 11ch =/= 10x 10ch?
12ch = 11ch I can understand, but why not reward the blocks finders?
Pool must reward miners according to hash rate only, not according to luck.12ch = 11ch I can understand, but why not reward the blocks finders?
Luck? I found several blocks, but was credited less than the half I should have got. I am going to solomine then. It was a good experience there though, just not good for bigger miners.
Any pool pays for shares according to your hashrate, not for blocks and mining calculator shows estimated profit in ideal conditions.
Core voltage: -60mV
Core clock: default (1018)
Mem. Clock: default (1250)
Temps 63 & 61.
Cpd 0.42 each.
Temps are good, they start temp throttling at 75. Core clock: default (1018)
Mem. Clock: default (1250)
Temps 63 & 61.
Cpd 0.42 each.
What's you real core speed? It could be hitting power limit.
Core 1: 935Mhz
Core 2: ~925-940Mhz
Where I can adjust power limit. Afterburner doesnt show that.
It should be there right below core voltage, +- 20%.
If you pump it you will get closer to temp limit + risking your 8-pin PCIE power cables + connectors.
Core voltage: -60mV
Core clock: default (1018)
Mem. Clock: default (1250)
Temps 63 & 61.
Cpd 0.42 each.
Temps are good, they start temp throttling at 75.
What's you real core speed? It could be hitting power limit.
Core 1: 935Mhz
Core 2: ~925-940Mhz
Where I can adjust power limit. Afterburner doesnt show that.
If anybody using RX 570? How much cpd do you get?
Core voltage: -60mV
Core clock: default (1018)
Mem. Clock: default (1250)
Temps 63 & 61.
Cpd 0.42 each.
Temps are good, they start temp throttling at 75.
What's you real core speed? It could be hitting power limit.
Jump to: