Topic: Pangolinminer & Whatsminer FAQs - page 7. (Read 25328 times)
Tried to reset, change the wires in places on the miner, Yang JYan from the support of the pangolin, installed a new program, nothing helped. They say it's good. I see that this is not normal at all. Probably, this SM2 board does not gain strength, and because of this, everything is overloaded. What do you think controller?
Definitely sounds like you should open a ticket with Pangolinminer. Have you tried the reset? It sounds like a controller issue.
After the automatic restart, the fans start working all the time at the level of 5900-6000, and the temperature drops 82-81-80. What is UpfreqCompleted 2?
P/S On the others M3 UpfreqCompleted 1, the miners work from November without failures in the ideal. I recommended the M3 to my friends, and I myself received one defective,, in a new batch
P/S On the others M3 UpfreqCompleted 1, the miners work from November without failures in the ideal. I recommended the M3 to my friends, and I myself received one defective,, in a new batch
I read on the forum as soon as errors appear on the chips, the controller makes several more attempts, checks that the errors are stable, and switches the frequency of the entire board back to the one on which there were no errors on the chips.
After an automatic restart, I see UpfreqCompleted 2
After an automatic restart, I see UpfreqCompleted 2
Good evening! SM0 620-635, medium SM1 always 636, SM2 590-611. First 635. 636. 611, and then after one minute the miner himself is overloaded and switches to the frequency of 624 636 600. and GH 10900-11300. It shows error E013
The speed of hashing is low. On the back of the miner, a red diode is constantly blinks.
The speed of hashing is low. On the back of the miner, a red diode is constantly blinks.
New M3 Normally does not work, reboots, Hash Rate 10-11.3 maximum, the frequency jumps all the time 600-618
Does the frequency jump on 1 board or all 3???
New M3 Normally does not work, reboots, Hash Rate 10-11.3 maximum, the frequency jumps all the time 600-618
Ok, 3x1.5mm2 C13 --> Type I power cord it is then.
Yeah it should do the job just fine, presuming that the cable condition is good and it is not damaged.
Yeah it should do the job just fine, presuming that the cable condition is good and it is not damaged.
What wire gauge does the power cord from socket to psu have?
It’s the cable provider by Pangolinminer together with the M3 and PSU.
They provide 1,5mm2 cable with the unit which does the job great and does not get warm.
I don't remember specs for the stock power cord, since I did not use it as we have Type F sockets here in Finland.
What wire gauge does the power cord from socket to psu have?
It’s the cable provider by Pangolinminer together with the M3 and PSU.
Hi all,
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
Guys you need to do some homework before runing a miner or you will ger your house burnt down. So M3 drains approx 2200w, if you are on 230v you should use 1,5mm2 cables. It should be rated 16amps. It should be also in a power circuit that is protected with 16A fuse.
1.5 mm2 - Max. circuit breaker size: 10 Amps
2.5 mm2 - Max. circuit breaker size: 16 Amps
This is how it is done in installations which comply with the IEC standards.
I know, when I said 1,5m2 16A I was refering to cable from miner to socket. The instalations in a house should be done by electrician so I consider it was done by standars.
What wire gauge does the power cord from socket to psu have?
Thanks and the electrician confirmed it’s 2.5mm2 wiring and the socket is working. However the plug of the power cable to M3 burnt after running for more than 36 hours. What else can be done to rectify this?
I was talking about wiring from the circuit breaker to the electrical socket.
Hi all,
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
Guys you need to do some homework before runing a miner or you will ger your house burnt down. So M3 drains approx 2200w, if you are on 230v you should use 1,5mm2 cables. It should be rated 16amps. It should be also in a power circuit that is protected with 16A fuse.
1.5 mm2 - Max. circuit breaker size: 10 Amps
2.5 mm2 - Max. circuit breaker size: 16 Amps
This is how it is done in installations which comply with the IEC standards.
Thanks for the advice. Can I please confirm if this 2.5mm2 cable is for electrical wiring from the DB breaker to the socket or for the power cord cable to connect from M3 to the socket?
Hi all,
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
Guys you need to do some homework before runing a miner or you will ger your house burnt down. So M3 drains approx 2200w, if you are on 230v you should use 1,5mm2 cables. It should be rated 16amps. It should be also in a power circuit that is protected with 16A fuse.
1.5 mm2 - Max. circuit breaker size: 10 Amps
2.5 mm2 - Max. circuit breaker size: 16 Amps
This is how it is done in installations which comply with the IEC standards.
Hi all,
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
Guys you need to do some homework before runing a miner or you will ger your house burnt down. So M3 drains approx 2200w, if you are on 230v you should use 1,5mm2 cables. It should be rated 16amps. It should be also in a power circuit that is protected with 16A fuse.
@gglala
That sounds like a short circuit issue.
That sounds like a short circuit issue.
Hi all,
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
I tried with a host for my M3s that I received 2 weeks ago but there’s not much luck What happened is that after running for 24 to 48 hours straight, the cables got burnt out once, another time the fuse of the socket got burnt. Anyone has similar challenge or able to advise how to overcome this? Thanks
Jump to: