Topic: Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment - page 5. (Read 104895 times)

Quote from: golfgrasshopper on March 09, 2014, 09:22:38 AM

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

Start cgminer in screen session then detach it Ctrl+a+d then exit then close putty
In general login via ssh
Type screen if you got error install it
In screen exec cgminer detach and exit

Thanks for the reply. When I logged in I typed sudo su so I'm in root as super user (thought I had to). Is there any way to get back to screen session as I don't want to shut down the miner. Sometimes it takes many restarts to get everything working correctly so I don't want to bail out of this session.

Screen -r
Read screen help and make sure you are reattaching session from same user account
All this stuff is happening in tplink with Thechnobit image. You should give it a try someday Wink

I'm not getting this. Sorry I feel like a dunce. I have cgminer running on the Putty terminal. The only options that I see are to type P,S,D or Q to bring up other options or quit. If I try to type nothing happens unless i hit one of the keys I just mentioned. If I type ctrl+a+d holding all keys down at once or any combination of them nothing happens. I did restart the program so I think I'm in screen but who knows.

Just invest some time reading and some time in trial and errors that is all i can say
Good luck

I tried ctrl+a+d again and now it works!!!! I guess I can follow simple instructions even if it takes me a few tries. Thanks a million for being so patient with me.

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: golfgrasshopper on March 09, 2014, 10:40:13 AM

Quote from: loshia on March 09, 2014, 10:19:50 AM

Quote from: golfgrasshopper on March 09, 2014, 09:58:16 AM

Quote from: golfgrasshopper on March 09, 2014, 09:22:38 AM

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

Start cgminer in screen session then detach it Ctrl+a+d then exit then close putty
In general login via ssh
Type screen if you got error install it
In screen exec cgminer detach and exit

Thanks for the reply. When I logged in I typed sudo su so I'm in root as super user (thought I had to). Is there any way to get back to screen session as I don't want to shut down the miner. Sometimes it takes many restarts to get everything working correctly so I don't want to bail out of this session.

Screen -r
Read screen help and make sure you are reattaching session from same user account
All this stuff is happening in tplink with Thechnobit image. You should give it a try someday Wink

I'm not getting this. Sorry I feel like a dunce. I have cgminer running on the Putty terminal. The only options that I see are to type P,S,D or Q to bring up other options or quit. If I try to type nothing happens unless i hit one of the keys I just mentioned. If I type ctrl+a+d holding all keys down at once or any combination of them nothing happens. I did restart the program so I think I'm in screen but who knows.

Just invest some time reading and some time in trial and errors that is all i can say
Good luck

golfgrasshopper

newbie

Activity: 7

Merit: 0

Quote from: loshia on March 09, 2014, 10:19:50 AM

Quote from: golfgrasshopper on March 09, 2014, 09:58:16 AM

Quote from: golfgrasshopper on March 09, 2014, 09:22:38 AM

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

Start cgminer in screen session then detach it Ctrl+a+d then exit then close putty
In general login via ssh
Type screen if you got error install it
In screen exec cgminer detach and exit

Thanks for the reply. When I logged in I typed sudo su so I'm in root as super user (thought I had to). Is there any way to get back to screen session as I don't want to shut down the miner. Sometimes it takes many restarts to get everything working correctly so I don't want to bail out of this session.

Screen -r
Read screen help and make sure you are reattaching session from same user account
All this stuff is happening in tplink with Thechnobit image. You should give it a try someday Wink

I'm not getting this. Sorry I feel like a dunce. I have cgminer running on the Putty terminal. The only options that I see are to type P,S,D or Q to bring up other options or quit. If I try to type nothing happens unless i hit one of the keys I just mentioned. If I type ctrl+a+d holding all keys down at once or any combination of them nothing happens. I did restart the program so I think I'm in screen but who knows.

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: golfgrasshopper on March 09, 2014, 09:58:16 AM

Quote from: golfgrasshopper on March 09, 2014, 09:22:38 AM

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

Start cgminer in screen session then detach it Ctrl+a+d then exit then close putty
In general login via ssh
Type screen if you got error install it
In screen exec cgminer detach and exit

Thanks for the reply. When I logged in I typed sudo su so I'm in root as super user (thought I had to). Is there any way to get back to screen session as I don't want to shut down the miner. Sometimes it takes many restarts to get everything working correctly so I don't want to bail out of this session.

Screen -r
Read screen help and make sure you are reattaching session from same user account
All this stuff is happening in tplink with Thechnobit image. You should give it a try someday Wink

marto74

hero member

Activity: 728

Merit: 500

Quote from: techman05 on March 07, 2014, 04:45:23 PM

Hey anyone know if there's a windows command to release a com port? I'm trying to connect to my miner port and its saying denied.

In device manager
Disable , then Enable of the COM port

golfgrasshopper

newbie

Activity: 7

Merit: 0

Quote from: golfgrasshopper on March 09, 2014, 09:22:38 AM

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

Start cgminer in screen session then detach it Ctrl+a+d then exit then close putty
In general login via ssh
Type screen if you got error install it
In screen exec cgminer detach and exit

Thanks for the reply. When I logged in I typed sudo su so I'm in root as super user (thought I had to). Is there any way to get back to screen session as I don't want to shut down the miner. Sometimes it takes many restarts to get everything working correctly so I don't want to bail out of this session.

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: golfgrasshopper on March 09, 2014, 09:22:38 AM

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

Start cgminer in screen session then detach it Ctrl+a+d then exit then close putty
In general login via ssh
Type screen if you got error install it
In screen exec cgminer detach and exit

golfgrasshopper

newbie

Activity: 7

Merit: 0

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

HI Guys,

I reflashed Raspbian and followed Zich's instructions to the letter by copying and pasting this time and everything was installed correctly. Thank you for all the help. Cgminer is now running and I filled in my pool details etc (eligius)when prompted. My problem is that everytime I exit putty cgminer shuts down. I couldn't see any options so I just click on the x in the top right corner of the window. I now know that's wrong. Anyone got a better method? Thanks again

marto74

hero member

Activity: 728

Merit: 500

Technobit HEX boards family simple setup guide
http://www.megafileupload.com/en/file/506573/TECHNOBIT-HEX16--Setup-pdf.html

cannachris

sr. member

Activity: 406

Merit: 250

cats love crypto | 911 truth @checktheevidence.com

Hey my second hex16a2 from order WVEFURYEA has just shorted my psu and made a lot of smoke and a very nasty smell and is 100% broken. The chips are ok though. I will have to return this one too, there is a burnt out spot on the board, and a blackened component just fell off. That makes two out of two hex16a2's broken, without any overclocking!
The other one should have reached you by now according to tracking. I will return this one too. And if possible I would prefer to put the refund money towards a coincraft miner, but if you send me two hex16a2's that's ok too.

Do you want me to take a picture of the board before I ship it back?.

I would really like to know whether you have received the miner and could let me know whether I will be getting new miners or store credit?

Will you keep me updated PLEASE?

Thanks!

techman05

hero member

Activity: 546

Merit: 500

Hey anyone know if there's a windows command to release a com port? I'm trying to connect to my miner port and its saying denied.

techman05

hero member

Activity: 546

Merit: 500

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

Gotta be missing something I'm doing those steps up till auto.sh on umbuntu and up to then it's fine . Maybe make sure the right packages are installed to understand the patch command.

Destiffmast

full member

Activity: 125

Merit: 100

Quote from: marto74 on March 05, 2014, 09:46:27 AM

the problem is in the stratum proxy
try to get newer from slush pool

That worked. Thanks :-)

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: golfgrasshopper on March 07, 2014, 08:40:37 AM

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Good luck

It's already time for me to sleep Cheesy

golfgrasshopper

newbie

Activity: 7

Merit: 0

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

I copied and pasted line 4,5 and 6 and still no joy. I'm just about to reflash raspbian and start from scratch. It will go much faster this time

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: golfgrasshopper on March 07, 2014, 08:24:56 AM

Quote from: golfgrasshopper on March 07, 2014, 07:41:39 AM

Hi Zich,

This is my first post and I don't know if I'm doing it correctly but here goes. I've never use Linux before but
I am trying to set up a couple of Technobit hex16a2's that I just purchased on ebay. I am using a Raspi loaded with Raspbian. I followed your instructions concerning loading and patching cgminer 3.12.3 and everything was working well until I tried to apply the patch. I get an error that states that the patch "unexpectedly ends in the middle of a line" and "only garbage was found in the patch input" Also I can't find the patch on Technobit's website
Is the file corrupted or am I missing something? Any help would be greatly appreciated

Hmm, did you type the command line by line or copy paste?
I bet that some line is miss when you type. You can copy then right click to paste it on ssh

You're right, I didn't realize that you can copy and paste into a terminal till near the end. I was typing and staring till my eyes bled ;-). I have now redone lines 5 and 6 with the same negative result. Maybe I have to start again from scratch and reflash raspbian to remove any transcription errors

I guess line 4 also not right Roll Eyes

golfgrasshopper

newbie

Activity: 7

Merit: 0