Swedish ASIC miner company kncminer.com - page 302.

proclivity

member

Activity: 67

Merit: 10

Quote from: user27 on July 11, 2014, 11:59:03 AM

Quote from: tolip_wen on July 11, 2014, 11:46:34 AM

Quote from: user27 on July 11, 2014, 11:40:55 AM

It just times out after a while/

Same from different browsers and different devices.

2nd die on first chip has not worked at any point; totally screwed I think.

Have you tried a ribbon cable from a working cube on that one?

YMMV

The other three dies on that cube work for the most part so I think cable issues are unlikely to be the cause; I have tried swapping that cube with another one i.e. different PCI-e cable, different PSU, different ribbon, different beagle socket/

I managed to get the firmware uploaded; must have tried 8 or 9 times that timed out and then it worked for no apparent reason. Now I have no advanced tab and additional errors:

1.1.x is ASIC 2 die 2, increase the V on that die. As Tiggger said that's an indication that the die/VRMs have turned off.

If you can't bring up the advanced tab try clearing browser cache. Also Elenelen reports it can take some time to load so give it a few minutes. Worst case, use putty to login and edit the VRM config file manually then reboot.

raskul

sr. member

Activity: 434

Merit: 250

Quote from: user27 on July 11, 2014, 12:30:30 PM

Quote from: raskul on July 11, 2014, 12:15:07 PM

you got something broken.

Thanks for the insight bud; I sure did.

Plus they will have gone home for the weekend now.

gutted
how many TH you was? 3TH/s? wots ur wallet address?

Tigggger

legendary

Activity: 1098

Merit: 1000

Lots of errors are usually accompanied by the affected die showing it's not running with 0v 0a on the advanced page.

I've had that a few times as I have been tweaking the voltages and speeds to get the best out of mine.

When it happens a 'reboot' won't usually fix it, so I would give the affected die more volts and/or drop the speed, apply the settings then physically power off the miner, most times it then comes back to life

user27

sr. member

Activity: 266

Merit: 250

Quote from: raskul on July 11, 2014, 12:15:07 PM

you got something broken.

Thanks for the insight bud; I sure did.

Plus they will have gone home for the weekend now.

raskul

sr. member

Activity: 434

Merit: 250

you got something broken.

Quote from: user27 on July 11, 2014, 10:01:13 AM

Quote from: aasl on July 11, 2014, 09:49:26 AM

try the "upgrade" tab on the knc web control page.

Tried it, the thing sits there and does nothing.

I just get "Sending request to 192.168.1....." and it carrys on mining.

One die is totally dead and this one is not looking much better:

EDIT:

Dead one:

user27

sr. member

Activity: 266

Merit: 250

Quote from: tolip_wen on July 11, 2014, 11:46:34 AM

Quote from: user27 on July 11, 2014, 11:40:55 AM

It just times out after a while/

Same from different browsers and different devices.

2nd die on first chip has not worked at any point; totally screwed I think.

Have you tried a ribbon cable from a working cube on that one?

YMMV

The other three dies on that cube work for the most part so I think cable issues are unlikely to be the cause; I have tried swapping that cube with another one i.e. different PCI-e cable, different PSU, different ribbon, different beagle socket/

I managed to get the firmware uploaded; must have tried 8 or 9 times that timed out and then it worked for no apparent reason. Now I have no advanced tab and additional errors:

tolip_wen

sr. member

Activity: 386

Merit: 250

Quote from: user27 on July 11, 2014, 11:40:55 AM

It just times out after a while/

Same from different browsers and different devices.

2nd die on first chip has not worked at any point; totally screwed I think.

Have you tried a ribbon cable from a working cube on that one?

YMMV

user27

sr. member

Activity: 266

Merit: 250

Quote from: aasl on July 11, 2014, 11:23:04 AM

it takes time to upload the 17MB file. you need to stay on the upgrade page and wait. after upload, it will upgrade the system, and then get restarted automatically. during the process, do not switch to other tabs. or the upgrade will be terminated.

If after upgrading you still have die issues, you can power off the PSU and power on again. my neppy sometimes also has die issues. using web page to restart the miner does not work, but a hard restart solves the problem.

It just times out after a while/

Same from different browsers and different devices.

2nd die on first chip has not worked at any point; totally screwed I think.

aasl

sr. member

Activity: 476

Merit: 250

Quote from: user27 on July 11, 2014, 10:01:13 AM

Quote from: aasl on July 11, 2014, 09:49:26 AM

try the "upgrade" tab on the knc web control page.

Tried it, the thing sits there and does nothing.

I just get "Sending request to 192.168.1....." and it carrys on mining.

One die is totally dead and this one is not looking much better:

EDIT:

Dead one:

it takes time to upload the 17MB file. you need to stay on the upgrade page and wait. after upload, it will upgrade the system, and then get restarted automatically. during the process, do not switch to other tabs. or the upgrade will be terminated.

If after upgrading you still have die issues, you can power off the PSU and power on again. my neppy sometimes also has die issues. using web page to restart the miner does not work, but a hard restart solves the problem.

user27

sr. member

Activity: 266

Merit: 250

Quote from: aasl on July 11, 2014, 09:49:26 AM

try the "upgrade" tab on the knc web control page.

Tried it, the thing sits there and does nothing.

I just get "Sending request to 192.168.1....." and it carrys on mining.

One die is totally dead and this one is not looking much better:

EDIT:

Dead one:

aasl

sr. member

Activity: 476

Merit: 250

Quote from: user27 on July 11, 2014, 09:31:50 AM

Quote from: sbbc on July 11, 2014, 09:24:30 AM

it was "screen -r cgminer" on my Saturn

That has done it, thanks.

Now I get to see 2.9TH and a screen full of "disabled for 300 seconds due to repeated hardware errors". Way more disabled cores than accepted shares.

Is it recommended to update to f/w 1.0? If so, how do I do it? (I have the bin file)

try the "upgrade" tab on the knc web control page.

user27

sr. member

Activity: 266

Merit: 250

Quote from: sbbc on July 11, 2014, 09:24:30 AM

it was "screen -r cgminer" on my Saturn

That has done it, thanks.

Now I get to see 2.9TH and a screen full of "disabled for 300 seconds due to repeated hardware errors". Way more disabled cores than accepted shares.

Is it recommended to update to f/w 1.0? If so, how do I do it? (I have the bin file)

aasl

sr. member

Activity: 476

Merit: 250

Quote from: sbbc on July 11, 2014, 09:24:30 AM

it was "screen -r cgminer" on my Saturn

Quote from: user27 on July 11, 2014, 09:09:51 AM

Quote from: aasl on July 11, 2014, 08:30:29 AM

username is root, password by default is "admin", and your password configured in web admin page will replace the default password

Thanks, I'm in. Now I don't know how to get the stats up.

@user27

yes. since there is only one background process running, it is okay to use just "screen -r" to show the cgminer stats. If you are new with screen command, be careful and never use "ctrl-C" to exit, as it will terminate the mining instance. always use "ctrl-A D" to detach the screen

aasl

sr. member

Activity: 476

Merit: 250

Quote from: user27 on July 11, 2014, 09:09:51 AM

Quote from: aasl on July 11, 2014, 08:30:29 AM

username is root, password by default is "admin", and your password configured in web admin page will replace the default password

Thanks, I'm in. Now I don't know how to get the stats up.

what stats? the output of cgminer?

sbbc

newbie

Activity: 12

Merit: 0

it was "screen -r cgminer" on my Saturn

Quote from: user27 on July 11, 2014, 09:09:51 AM

Quote from: aasl on July 11, 2014, 08:30:29 AM

username is root, password by default is "admin", and your password configured in web admin page will replace the default password

Thanks, I'm in. Now I don't know how to get the stats up.

user27

sr. member

Activity: 266

Merit: 250

Quote from: aasl on July 11, 2014, 08:30:29 AM

username is root, password by default is "admin", and your password configured in web admin page will replace the default password

Thanks, I'm in. Now I don't know how to get the stats up.

bitgeek

sr. member

Activity: 462

Merit: 251

Quote from: Searing on July 11, 2014, 02:46:23 AM

Quote from: s1gs3gv on July 10, 2014, 08:54:28 PM

Now that GAW have upgraded all VaultBreakers to 750mhs and are offering batch 2 VB for $6999 I wonder what kind of competitive response we will see from KNC ?

https://hashtrader.com/t/vault-breaker-update/2388

er nothing...no refunds....eat it ...(by that point in time say 3rd batch Titans they will be announcing their 3 Titan PH Farms anyway lol)

Searing

That's why pre-orders suck

With the new Vaultbreakers you'll be getting 750MH for $7000
If you wanted to beat this with Titans you'd have to spend $14000 for 800MH - ridiculous!

aasl

sr. member

Activity: 476

Merit: 250

Quote from: user27 on July 11, 2014, 07:20:28 AM

Neptune arrived dispite me requesting refund nearly a month ago.

It has been beaten up in transit and runs like a pig; hot VRM's and dead dies.

What's the SSH password?

username is root, password by default is "admin", and your password configured in web admin page will replace the default password

edgar

legendary

Activity: 1848

Merit: 1001

note to whoever it was who unmasked 'mauiflipper et al' - so many ppl came fwd i forget who it was that PM'd me the complete details.

https://nxtforum.org/general-discussion/klee-bounty!/

get er done!

user27

sr. member

Activity: 266

Merit: 250

Neptune arrived dispite me requesting refund nearly a month ago.

It has been beaten up in transit and runs like a pig; hot VRM's and dead dies.

What's the SSH password?

Topic: Swedish ASIC miner company kncminer.com - page 302. (Read 3049515 times)