Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 847.

Xardas2014

hero member

Activity: 635

Merit: 500

Quote from: enricosofie on June 05, 2017, 01:48:53 AM

Quote from: Xardas2014 on June 05, 2017, 01:38:43 AM

Quote from: enricosofie on June 05, 2017, 01:29:43 AM

Hi,

I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.

Any ideas?

regards,
eric

First I would reset the CMOS.

i 've tried that!
But no luck!!!

Ok next I would try getting the board to boot to the bios.........nothing connected like you did before, except this time try only one stick of mem you dam sure is good. Try it in each slot to see if you can get to the bios. Don't forget to disconnect the drive your OS is on.

Xardas2014

hero member

Activity: 635

Merit: 500

Quote from: RomeSC on June 04, 2017, 06:39:59 PM

havent seen this answer yet, hoping for quick clarification.

I have 3 rx 480s and, newly acquired, for ethereum mining with Claymore's. I am trying to find a way to write bat files that lets me game on the top 2 480s while 24/7 mining with the 3rd card. Essentially I need crossfire to ignore the 3rd card so it can mine without screwing up my gaming. I am on windows 7 64-bit

When I'm not gaming ill mine with all 3 480s.

Is anyone able to help with this conundrum? Seems like it should be simple but I can't figure it out. Thanks in advance.

First page RTFM. You can turn on cards ON in your .bat OR you can turn cards on/off during mining. Either would work, but turning a card on/off would be simpler and prevent restarting Claymore.

enricosofie

newbie

Activity: 47

Merit: 0

Quote from: Xardas2014 on June 05, 2017, 01:38:43 AM

Quote from: enricosofie on June 05, 2017, 01:29:43 AM

Hi,

I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.

Any ideas?

regards,
eric

First I would reset the CMOS.

i 've tried that!
But no luck!!!

Xardas2014

hero member

Activity: 635

Merit: 500

Quote from: TechPark on June 05, 2017, 12:23:46 AM

Quote from: lazyturtle on June 03, 2017, 04:40:54 PM

Hello everyone. I have a problem with one of my rigs.

I get the ""WATCHDOG: GPU 0 hangs in OpenCL call, exit" problem after about 20-60 min running the claymore miner. It started tough with that my miner was loosing internet connection after running a while. When i fixed that by installing new network adapter drivers, the connection was stable but the GPU´s started to give 0.00 mh´s after a while, until getting the error message.

I did overclock the rig in the beggining, but i have reseted the MSI afterburner settings to default and i also did a bios mod, but i flashed the cards back to the original bios. I also dont think that the bios mod was the problem, because i have 3 more rigs with rx 470 with the same mod, and they all work great.

Specs:
Intel Celeron G1840 Processor
Asrock H81 Pro BTC motherboard
6x AMD Radeon RX 470 4GB
4GB DDR3 Memory
60GB SDD Harddisk
1000W Gold power supply
Windows 10 operating system

I have already tried to:
- Run the miner with the gser and eser commands and have also tried both dual and solo mining(both have same problems).
- fresh install of both operating system and Gpu drivers (first gpu drivers with DDU and after that operating system).
- Checked every riser, but they all work on a diffrent system so thats not the problem.
- Setting virtual memory to atleast 16000
- Tried old claymore miners, from 6.3 and up, same problem.

I dont really know what to do at this point, would really appreciate help if someone knows what might be causing this.

leave 1 card only, remove other cards a mine for 2 hours. If the miner does not crash replace the card and repeat the test. If you do not find a "faulty card" by trying all 6 then start adding cards - two for 2 hours, 3 for 2 hours, 4 for 2 hours, 5 for 2 hours and finally 6. Post the results of these tests here.

First thing I would check is to see if Win10 changing virtual mem settings during an update(which I see you checked), or updated the drivers. Both things are on the same pop up. After checking virtual mem on the advance tab, click on the hardware tab and tell winblows to not update drivers. Winblows will update drivers as it boots. Also what are the card temps when they shut down or start spitting out opencl errors?

Xardas2014

hero member

Activity: 635

Merit: 500

Quote from: enricosofie on June 05, 2017, 01:29:43 AM

Hi,

I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.

Any ideas?

regards,
eric

First I would reset the CMOS.

enricosofie

newbie

Activity: 47

Merit: 0

Hi,

I have a problem with a rig.
Yesterday I removed an older R9 card. Now there are only 4 x RX480s in the rig.
When I started the rig, it started-stoped-started-stoped-started but no screen, no beeps, nothing.
I removed all unnecessary things (so only cpu and mem is on the motherboard) and stil the same!
The mainboard is an Asrock btc pro.
CPU is an intel G1840
Ii tried a couple of different memory.
Power supply is an EVGA 1600 G2.

Any ideas?

regards,
eric

samhayne

jr. member

Activity: 40

Merit: 1

Quote from: djazher on June 04, 2017, 05:25:54 PM

372.54 worked perfectly for me, but I'm on win7, so might be that.

I thought on Win 7 there wouldn't be any hash rate issues at all.

Oh man...
Somehow I get the impression that it's running for 90% of the Win 10 users by now
and for some it "just" doesn't work. But there MUST be a reason!

edit:
- Used driver 368.81 (as proposed by Claymore's miner) - still 3 Mh/s.
- Using the Cuda 6.5 version also didn't help

TechPark

full member

Activity: 238

Merit: 100

Quote from: lazyturtle on June 03, 2017, 04:40:54 PM

Hello everyone. I have a problem with one of my rigs.

I get the ""WATCHDOG: GPU 0 hangs in OpenCL call, exit" problem after about 20-60 min running the claymore miner. It started tough with that my miner was loosing internet connection after running a while. When i fixed that by installing new network adapter drivers, the connection was stable but the GPU´s started to give 0.00 mh´s after a while, until getting the error message.

I did overclock the rig in the beggining, but i have reseted the MSI afterburner settings to default and i also did a bios mod, but i flashed the cards back to the original bios. I also dont think that the bios mod was the problem, because i have 3 more rigs with rx 470 with the same mod, and they all work great.

Specs:
Intel Celeron G1840 Processor
Asrock H81 Pro BTC motherboard
6x AMD Radeon RX 470 4GB
4GB DDR3 Memory
60GB SDD Harddisk
1000W Gold power supply
Windows 10 operating system

I have already tried to:
- Run the miner with the gser and eser commands and have also tried both dual and solo mining(both have same problems).
- fresh install of both operating system and Gpu drivers (first gpu drivers with DDU and after that operating system).
- Checked every riser, but they all work on a diffrent system so thats not the problem.
- Setting virtual memory to atleast 16000
- Tried old claymore miners, from 6.3 and up, same problem.

I dont really know what to do at this point, would really appreciate help if someone knows what might be causing this.

leave 1 card only, remove other cards a mine for 2 hours. If the miner does not crash replace the card and repeat the test. If you do not find a "faulty card" by trying all 6 then start adding cards - two for 2 hours, 3 for 2 hours, 4 for 2 hours, 5 for 2 hours and finally 6. Post the results of these tests here.

Bob_chemist

newbie

Activity: 28

Merit: 0

Claymore,

can you add a small feature to Monitor, please: the time how long rig stays offline (red).
It will be very useful

Teress

full member

Activity: 224

Merit: 102

Quote from: rintic13 on June 04, 2017, 11:39:44 PM

@Claymore
I have several cards RX460 on 15.1 Mh. Enable support ASM algoritm for 460, please

Yes, it would be great. I was talking about it with Claymore about 1.5 month ago, but it seems the support for RX460 is still not there. And what about RX 560?

BTW: how did you achieve 15Mhs from it??

rintic13

newbie

Activity: 3

Merit: 0

@Claymore
I have several cards RX460 on 15.1 Mh. Enable support ASM algoritm for 460, please

DefiantMiner

newbie

Activity: 20

Merit: 0

Claymore,

There's a bug in the Monitor. Rig profiles get screwed up when font is changed...at least I think that's what's doing it. It blows away some of the rig sets. Other times it doesn't save the window frame and set. Buggy.

Can we get a fix soon?

Thx.

Deuce2High

newbie

Activity: 1

Merit: 0

Hey guys newb here researching mining and cryptos lately. Question about a dual-miner like this; Since PoS is coming soon, will this mining software (or similar) be changed to replace the Eth part of the mining with another coin? That way mining rigs can retain more value after PoS. Thanks.

supertux1

newbie

Activity: 15

Merit: 0

Why does Claymore remove my first pool in epools.txt?

Code:

POOL: us1.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: us2.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: eu1.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: eu2.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0

Code:

20:53:38:264	1744	Pool us1.ethermine.org removed from the list
20:53:38:264	1744	ETH: 3 pools are specified
20:53:38:264	1744	Main Ethereum pool is us2.ethermine.org:4444
20:53:38:264	1744	SC: 5 pools are specified
20:53:38:264	1744	Main Siacoin pool is sia-us-west1.nanopool.org:7777

Here's how I fooled it:

Code:

POOL: us1.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: us1.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: us2.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: eu1.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0
POOL: eu2.ethermine.org:4444, WALLET: 0xxxx.worker1, PSW: x, ESM: 1, ALLPOOLS: 0

kirptc

newbie

Activity: 5

Merit: 0

I have a biostar TB250 BTC MB and 6 Aorus RX580 GPUs. I am running 17.5.2 drivers on Windows 10 pro. Windows will recognize all 6 cards. Claymore 9.4 will start with 4 cards, but when there are 5 or 6 it will not get past the initializing OpenCL.

Any idea what is causing this? I have a work trip this week and would like to get this fixed before I leave for it.

I will pay a consulting fee if someone can help me. PM me for details.

Thanks

RomeSC

newbie

Activity: 1

Merit: 0

havent seen this answer yet, hoping for quick clarification.

I have 3 rx 480s and, newly acquired, for ethereum mining with Claymore's. I am trying to find a way to write bat files that lets me game on the top 2 480s while 24/7 mining with the 3rd card. Essentially I need crossfire to ignore the 3rd card so it can mine without screwing up my gaming. I am on windows 7 64-bit

When I'm not gaming ill mine with all 3 480s.

Is anyone able to help with this conundrum? Seems like it should be simple but I can't figure it out. Thanks in advance.

matttheazn

newbie

Activity: 8

Merit: 0

Hi I am having trouble with setting a stop temperature and restarting the miner. In my command line I have "-wd 1 -r 1 -tstop 90" I have a reboot.bat(windows 10) file with a shutdown command in the same directory. When I hit the bat it will shutdown the computer. For testing purposes I am using -tstop 55. It stops mining correctly but how to I get it to execute the reboot.bat file? What am I doing wrong? thanks

vacs03

member

Activity: 63

Merit: 10

any guide for setting up http mode for the monitor app?

xTommYx

member

Activity: 190

Merit: 11

Quote from: kirilvvbg on March 19, 2017, 06:44:23 PM

Any suggestions why (after 3 hours of steady mining) I got this message:

Quote

Cannot get Overdrive capabilities for adapter 0
Cannot get Overdrive capabilities for adapter 6
Cannot get Overdrive capabilities for adapter 12
Cannot get Overdrive capabilities for adapter 18
Cannot get Overdrive capabilities for adapter 24
Cannot get Overdrive capabilities for adapter 30
Cannot get Overdrive capabilities for adapter 36

Same problem with a 2 rx480 cards rig.
Any reasons why this problem occurs after an hour or two or three?
What is the solution?

djazher

newbie

Activity: 41

Merit: 0