Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 865.

lautre

jr. member

Activity: 45

Merit: 1

it's only me or there is problems with the latest ethman? it lose connection to rig even if the rig is still up and mining..

ciripel1289

newbie

Activity: 50

Merit: 0

Hi,
When u have a share accepted on different pools, u also have (xxx ms!)
Is this time better to be low or high?
I suppose lower is better but want to be sure since i live in Europe and when i connected to an eu endpoint of a netwprk i got higher time in ms then when i connected in us endpoint. Can also someone explain why i got lower time on bigger the distance?
Thank you,

delle54

sr. member

Activity: 307

Merit: 250

Quote from: nils8107 on May 26, 2017, 12:15:18 PM

Hi all

I`m new here.

I downloaded "Claymore's Dual Ethereum+Decred_Siacoin_Lbry_Pascal AMD+NVIDIA GPU Miner v9.4"

And I added in my Config File my -ewal my key.

Code:

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!

-[b]mode 1[/b] I only want ETH mining...
-epool us1.ethpool.org:3333
-ewal [b]da4fd02b79e1f3cebbf581786f1a2e174ee931f9[/b] my key
-epsw x

Otherwise I did nothing.
I have a GTX1080 and a GTX970 and a I7 7700k and 16GB RAM.

Then I run start file...

Why its still calculating DCR?

Any tips for me? Thank you so much in advance.

Remove the text formating and comments.

supertux1

newbie

Activity: 15

Merit: 0

Quote from: rawnet on May 26, 2017, 01:53:05 AM

Hi,

Today when I started dual mining (ETH+DCR) on my Asus RX580 STRIX 8GB (Samsung memory) after few minutes computer hangs up?

I don't undervolt - I've only copied 1750 straps to 2000.

When I mine solo only ETH it works just fine - tested for 24h without any problem.

Any clues?

Oh... I'm on Crimson 17.5.2 Beta drivers.

A couple of things you can do (one at a time. don't change two things at once.)

1. Try adjusting the -dcri value from its default of 30 to say, 15, and start from there. (-/+ on the keyboard as it's mining.)
2. Undervolt with WattTool -100mV
3. Lower the GPU processor speed to something like 1150 or 1125. (edit bios)
4. Put the 2000 straps back and try to make memory faster by overclocking it instead.

How'd you get those drivers to work with the modified bios?

supertux1

newbie

Activity: 15

Merit: 0

So I was playing around with Jukebox's ROM for Sapphire RX480 Nitro+OC 8GB

One of my video cards won't take the v4.rom (2150Mhz / 1750 straps) because it has shitty memory. (Even though GPU-Z says it has a quality ASIC, go figure...)
It wouldn't even reliably run the runner up: vdrop+.rom which is 2080Mhz / 1625 straps. (I think.)

The v4.rom showed failure right away, 0.000 Mh/s and crash.
The vdrop+.rom would start off fine, then slowly degrade to 26Mh/s and result in OpenCL GPU errors after about 30 minutes or less. Many reboots.
(I only achieved stability by WattTooling it down to stock 2000Mhz on boot before running Claymore.)

So after experimenting made my own version of the vdrop+.rom which works well as a third option for dumb cards.
All I did was modify the existing one from 2080Mhz to 2050Mhz and drop the memory voltage from 1000mv to 900mV.

This got me at least a 1.5Mh/s gain on the dumb card, it used to read 27.5 - 28.1Mh/s max, now it reaches 29.1Mh/s, very rarely touching 28Mh/s.

The whole rig is doing a total of 178-179 Mh/s-ish (I really wanted 180 damn) but I'll take it.
SC mining is also running at 2980 to 3030 Mh/s with %0.4 rejected shares which I attribute to the nicehash pool latency/design. (-dcri 17)

TunerDude007

sr. member

Activity: 464

Merit: 252

Quote from: spunkybd on May 26, 2017, 04:25:48 PM

I have 4 GPU's.

What do I need to do to get Eth+Sia working on windows?

EthDcrMiner64.exe -epool eu1.nanopool.org:9999 -ewal 0xd69af2a796a737a103f12d2f0bcc563a13900e6f -epsw x -eworker rig1

miningpoolhub Ethereum+Siacoin:
EthDcrMiner64.exe -epool us-east1.ethereum.miningpoolhub.com:20536 -ewal 0xD69af2A796A737A103F12d2f0BCC563a13900E6F -eworker YourLogin.YourWorkerName -epsw x -allpools 1 -dpool stratum+tcp://hub.miningpoolhub.com:20550 -dwal username.workername -dpsw x -dcoin sia
you must also create worker "YourWorkerName" on pool and specify your wallet address there.

spunkybd

full member

Activity: 260

Merit: 102

I have 4 GPU's.

What do I need to do to get Eth+Sia working on windows?

EthDcrMiner64.exe -epool eu1.nanopool.org:9999 -ewal 0xd69af2a796a737a103f12d2f0bcc563a13900e6f -epsw x -eworker rig1

Lukke

newbie

Activity: 53

Merit: 0

Hello. On some miners, I got "watchdog: GPU 1 hangs in OpenCL call, exit" and it hangs during the next start - see the attachment. Then I have to manually shut down the miner and sometimes even restart PC. I have modded bios (straps 1750 to 2000) and ram overclock. But even if I lowered the memory clock, it still hangs... Does any -parametr will help me to solve this situation? Or what to do with this? Using RX480, 580, 570... It happends on all the cards. Thank you!

joelitoup

member

Activity: 231

Merit: 10

the best config for nvidia 1050ti EVGA? can help me? I'm mining 11 Mhz

Victorio

full member

Activity: 281

Merit: 100

Quote from: ?? on ??

You sir, are correct. Well, two small comments - it is often the VRAM, but sometimes can be the VRM. Also, it's only usually solved by running the fan at 100% and dropping volts... I have these shitty XFX RS XXX 480/470 GPUs (with the hard-swap fans)

I also have the XFX RS 480, the heatsink is not connected with the VRAM, as in Sapphire Nitro or other models.
I checked the temperature of VRAM with a pyrometer: when GPU core is at 65C, the mem chips from the upper array (http://imgur.com/eMOWJyl) would go close to 98-103C, so I lowered target temp to 57C (it takes about 2500-2800 RPM in solo mode and 3300 RPM in dual mode, ambient temp 22-25C). Now the mem chips are about 78-88 C when dual mining.

mantor84

member

Activity: 63

Merit: 10

Quote from: mantor84 on May 26, 2017, 01:51:47 AM

Quote from: MinerosYV on May 25, 2017, 07:59:53 PM

Quote from: mantor84 on May 25, 2017, 07:34:08 PM

hi guys...I really need your help.

I don't know why...but the watchdog error is killing me. I mean I have no idea what I could do to solve this issue.

My current rig looks like that:
7x RX580 Sapphire Nitro+ 8GB
8GB RAM
Windows 10
Virtual Memory min 2000 max 50000 (increased that much just to see if its working better...but it isn't)
Temp: 52-58°C
Fan: 60%
- ethi 4
- gser 2

The hole system is running but after some minutes/hours I get an watchdog error mostly at GPU4.
I checked everything used new riser even from an other manufacturer but it doesn't work.

The new Claymore V9.4 miner doesn't help.

If I have an Watchdog error I need to reboot my hole system an normally restart of Claymore never worked for me even from the beginning. Undecided

My watchdog is looking like that:
01:14:59:055   1a28   watchdog - thread 0 (gpu0), hb time 109
01:14:59:056   1a28   watchdog - thread 1 (gpu0), hb time 31
01:14:59:056   1a28   watchdog - thread 2 (gpu1), hb time 94
01:14:59:056   1a28   watchdog - thread 3 (gpu1), hb time 16
01:14:59:056   1a28   watchdog - thread 4 (gpu2), hb time 47
01:14:59:056   1a28   watchdog - thread 5 (gpu2), hb time 125
01:14:59:057   1a28   watchdog - thread 6 (gpu3), hb time 31
01:14:59:057   1a28   watchdog - thread 7 (gpu3), hb time 109
01:14:59:057   1a28   watchdog - thread 8 (gpu4), hb time 8297
01:14:59:058   1a28   watchdog - thread 9 (gpu4), hb time 8375
01:14:59:058   1a28   watchdog - thread 10 (gpu5), hb time 47
01:14:59:058   1a28   watchdog - thread 11 (gpu5), hb time 125
01:14:59:058   1a28   watchdog - thread 12 (gpu6), hb time 141
01:14:59:059   1a28   watchdog - thread 13 (gpu6), hb time 63

GPU 4 watchdog is way too high... and I hope you can give me some tipps to solve this.

Am I the only one who has that issue? Huh

couldn't find a solution at www.

If you need more information let me know.

appreciate for any help.

PS: approx. 3-4 days ago I could mine over 100 hours in a row and I didn't change anything till then.

It sounds like W10 updated and is messing with it, we are having problems with the 7 cards rigs, since a couple of weeks as a resul of an update, reset your system to a previus date.
We had some space left on some other rigs so took it down to 5.
Thats why we are building no more that 4 cards rigs now.
Should try ti change the GPU4 raiser just in case.

I had deactivated all W10 updates and all my GPUs can be detected in windows and with claymore.
So I think it should be OK with it... or not? Huh

I changed the raiser also once ...no effect.

Really strange and frustrating that watchdog issue it doesn't work for longer than 15min Angry

I've OC all cards the same like that "if its important"
GPU clock: 1150
Memory clock: 2150
GPU voltage: -75mv
Hynix all 7 gpus

Started Dual mining again (ETH + DCR) and it's running for almost 4,5hours without a watchdog error.
Can it be that only ETH mining is buggy with the Claymore client?
Didn't change anything just switched back to ETH+DCR instead of only ETH mining and it seems to run.

Will let you know if its fine now or if the watchdog error comes back.

btw does anyone else have problems with only ETH mining on the Claymore client?

nils8107

newbie

Activity: 22

Merit: 0

Hi all

I`m new here.

I downloaded "Claymore's Dual Ethereum+Decred_Siacoin_Lbry_Pascal AMD+NVIDIA GPU Miner v9.4"

And I added in my Config File my -ewal my key.

Code:

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!

-[b]mode 1[/b] I only want ETH mining...
-epool us1.ethpool.org:3333 
-ewal [b]da4fd02b79e1f3cebbf581786f1a2e174ee931f9[/b] my key
-epsw x

Otherwise I did nothing.
I have a GTX1080 and a GTX970 and a I7 7700k and 16GB RAM.

Then I run start file...

https://www2.pic-upload.de/img/33232144/mining2.jpg

Why its still calculating DCR?

Any tips for me? Thank you so much in advance.

XManiac

newbie

Activity: 26

Merit: 0

Quote from: ?? on ??

Can you tell my whicj pool you are working on? And show me your config file? That would be really appreciated

Code:

EthDcrMiner64.exe -di 0 -epool eu1.ethermine.org:4444 -ewal (wallet) -mode 1

config file is empty.

lautre

jr. member

Activity: 45

Merit: 1

i got 4x 480 with Elpida and 3x with samsung, Elpida can't go over 1900/1950mhz..

muratizm

member

Activity: 84

Merit: 10

Why google drive says there is a virus in 9.4 windows version?
It doesn't let us download.

XManiac

newbie

Activity: 26

Merit: 0

Quote from: wtfonly16 on May 26, 2017, 09:48:34 AM

how are people getting 30mh/s with sgminer 5.5.5 on rx570 wtf???

Im wonder how they getting 18GH/s with 1 worker and reported ~150MH/s

wtfonly16

full member

Activity: 285

Merit: 105

how are people getting 30mh/s with sgminer 5.5.5 on rx570 wtf???

XManiac

newbie

Activity: 26

Merit: 0

Quote from: ?? on ??

Hello Guys.

I recently set up Claymore for mining on my 970sli....
When i run mining i reach 3 MH/s for each card....

Here is my bat file:

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100...

Hi there!
I have 970 and reach 18MH/s, its strange.

Code:

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

Is not needed for Nvidia cards as i understand.

Question to all.
As i wrote above, i have GTX 970 card and 18MH/s on it, it's about 1ETH per 2 month. Is it worth it to buy a second card? It'll cost me a ~200$ and i would can make 1eth per month.

notbatman

legendary

Activity: 2212

Merit: 1038

A lot of the problems I'm reading here are most likely caused by overheating VRAM and can be solved by running the fan at 100% and lowering the clock speeds and/or voltages. The primary tempeture sensor is connected to the gpu and doesn't reflect how hot the VRAM is getting.

alrami

member

Activity: 92

Merit: 10

Quote from: z0n0 on May 26, 2017, 07:46:31 AM

New with RX480 cards...need some info/help.

I tried to mod rom, copied 1750 strap to 2000 strap. After reset I got the yellow exclamation on the card...so I must disable driver signature.
Is this the correct way to do it:

Code:

bcdedit.exe /set nointegritychecks on

or:

Code:

bcdedit.exe -set loadoptions DDISABLE_INTEGRITY_CHECKS
bcdedit.exe -set TESTSIGNING ON

Card is XFX RX480 GTR 8GB, Samsung memory ( http://www.xfxforce.com/en-us/products/amd-radeon-rx-400-series/rx-480-gtr-8gb-dd-led-rx-480p8dfa6 )
I'm using WIN10 Pro X64 & latest AMD driver

Maybe someone wants to share already moded .rom for this card?

Thanks, cheers y'all Cool

Try older drivers
16.11.5 works fine

Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 865. (Read 6590565 times)