Topic: Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux) - page 987. (Read 6590718 times)

Hello there, i made my first rig, but i have some problems with it. Every 6-7-8 hours it stops working, pool sends me a mail that my rig is not working, i connect through teamviewer and just press S to show what is going on, and miner restarts and continues normally.

This is end of log from claymore miner, and every time i had this message Miner thread hangs, need to restart miner!

I tried different versions of claymore but it just stops working after a while

08:32:00:891   1208   Miner thread hangs, need to restart miner!
08:32:00:895   8d8   ETH - Total Speed: 0.000 Mh/s, Total Shares: 1327, Rejected: 0, Time: 08:49
08:32:00:931   8d8   ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s, GPU4 0.000 Mh/s, GPU5 0.000 Mh/s
08:32:00:882   8b8   
08:32:00:967   8b8   GPU #0: Ellesmere, 8192 MB available, 36 compute units
08:32:00:972   8b8   GPU #1: Ellesmere, 8192 MB available, 36 compute units
08:32:00:977   8b8   GPU #2: Ellesmere, 8192 MB available, 36 compute units
08:32:00:981   8b8   GPU #3: Ellesmere, 8192 MB available, 36 compute units
08:32:00:987   8b8   GPU #4: Ellesmere, 8192 MB available, 36 compute units
08:32:00:991   8b8   GPU #5: Ellesmere, 8192 MB available, 36 compute units
08:32:00:997   8b8   ETH - Total Speed: 0.000 Mh/s, Total Shares: 1327, Rejected: 0, Time: 08:49
08:32:01:004   8b8   ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s, GPU4 0.000 Mh/s, GPU5 0.000 Mh/s
08:32:01:009   8b8   Incorrect ETH shares: none
08:32:01:014   8b8   Pool switches: ETH - 0, DCR - 0
08:32:01:019   8b8   Current ETH share target: 0x0000000112e0be82 (diff: 4000MH), epoch #113
08:32:01:086   8b8   GPU0 t=26C fan=52%, GPU1 t=25C fan=52%, GPU2 t=29C fan=53%, GPU3 t=28C fan=53%, GPU4 t=28C fan=53%, GPU5 t=25C fan=53%
08:32:01:090   8b8   
08:32:01:961   1208   Restarting OK, exit...

Is it possible, that with a Sapphire RX 480 Nitro+ OC 8GB  (1342 MHz) I do not get more than 28.1 MH/s ? And I have uploaded a BIOS with adjusted timing straps (2000)
If I raise the memory from 2000 MHz to some higher values, it has no effect. The miner is showing the same values: 28.1

what are the advantages of PASL that makes it better then PASC?

I am the dev of Pascal Lite,

We are in need of more miners to keep the network more secure and need more miners on PASL Suprnova's pool to keep hashrate distribution equal.

If you switch from PASC to PASL you can currently earn 30% more daily profit

All you need to switch is one line

-dpool stratum+tcp://pasl.suprnova.cc:4316





Thanks in advance


References

http://whattomine.com/coins/172-pasc-pascal?utf8=%E2%9C%93&hr=1000&p=0&fee=0.0&cost=0&hcost=0.0&commit=Calculate
http://whattomine.com/coins/177-pasl-pascal?utf8=%E2%9C%93&hr=1000.0&p=0.0&fee=0.0&cost=0.0&hcost=0.0&commit=Calculate

I tried Gen 1 with no Avail.  Thanks for the input Xiadas!

Change the PCIE slot to Gen 1.

It should work... are you sure the risers are ok? or for the x16 you don't use riser...

Single mining and never had this problem until drivers updated but since managed to get working again with custom bios switched to normal mode and then installed drivers and reverted back o silent mode with custom bios on. Took a lot to get working again was getting to point where was about to flash back but the bios and cards can handle 29MH on ETH and close to 300H/s on zec

Are you dual mining ETH + DCR?

You need to force it back to gen2 if I recall correctly.. I used to use them as well and did a bunch of 6 GPU deployments with them but had to force those changes for it to work.

Thank you @ciprianpt do you know if this bios will work on red devils rx480 8gb? does it produces memory errors?

Win10 Pro

Are you using Win 7? I have also 2 of them and with Win 10 are working great since August last year. No need to set it to GEN 2...

Thank you for the suggestions.  Not working yet.  It is set to GEN 2.  No effect. 

I have 6 MSI RX470 Gaming X GPUs with a 1200W PSU.