[ANN] Technobit HEX16B(Bitfury based) 16 chip board design - page 27.

berny81

full member

Activity: 200

Merit: 100

Quote from: Zich on December 13, 2013, 05:42:05 AM

I was wondering if the problem nanofury had serial number on it because it's need serial number to work. You can check it using -D -d? .

this is the output of sudo ./bfgminer -D -d? on ubuntu 10.04 64bit, the serial it apper to his present.

Code:

 [2013-12-13 12:02:50] Timers: Using clock_gettime(CLOCK_MONOTONIC)                    
 [2013-12-13 12:02:50] Global quota greatest common denominator set to 1                    
 [2013-12-13 12:02:50] setrlimit: Soft fd limit not being changed from 1024 (FD_SETSIZE=1024; hard limit=1024)                    
 [2013-12-13 12:02:50] Started bfgminer 3.8.0                    
 [2013-12-13 12:02:50] Loaded configuration file /home/berny/.cgminer/cgminer.conf                    
 [2013-12-13 12:02:51] hidapi_try_lib: Couldn't load libhidapi.so: libhidapi.so: cannot open shared object file: No such file or directory                    
 [2013-12-13 12:02:51] hidapi_try_lib: Couldn't load libhidapi-0.so: libhidapi-0.so: cannot open shared object file: No such file or directory                    
 [2013-12-13 12:02:51] hidapi_try_lib: Successfully loaded libhidapi-hidraw.so                    
 [2013-12-13 12:02:51] hid_devinfo_scan: Found "MCP2210 USB to SPI Master" serial "0000034904"                    
 [2013-12-13 12:02:51] hid_devinfo_scan: Found "USB-PS/2 Optical Mouse" serial "(null)"                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:003:001 (path=(null), vid=1d6b, pid=0001, manuf=Linux 2.6.32-38-generic uhci_hcd, prod=UHCI Host Controller, serial=0000:00:1a.0)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:004:001 (path=(null), vid=1d6b, pid=0001, manuf=Linux 2.6.32-38-generic uhci_hcd, prod=UHCI Host Controller, serial=0000:00:1a.1)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:001:001 (path=(null), vid=1d6b, pid=0002, manuf=Linux 2.6.32-38-generic ehci_hcd, prod=EHCI Host Controller, serial=0000:00:1a.7)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:001:002 (path=(null), vid=04f2, pid=b033, manuf=(null), prod=USB2.0 1.3M UVC WebCam, serial=(null))                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:005:001 (path=(null), vid=1d6b, pid=0001, manuf=Linux 2.6.32-38-generic uhci_hcd, prod=UHCI Host Controller, serial=0000:00:1d.0)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:005:005 (path=(null), vid=04d8, pid=00de, manuf=Microchip Technology Inc., prod=MCP2210 USB to SPI Master, serial=0000034904)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:005:004 (path=(null), vid=046d, pid=c03d, manuf=Logitech, prod=USB-PS/2 Optical Mouse, serial=(null))                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:006:001 (path=(null), vid=1d6b, pid=0001, manuf=Linux 2.6.32-38-generic uhci_hcd, prod=UHCI Host Controller, serial=0000:00:1d.1)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:007:001 (path=(null), vid=1d6b, pid=0001, manuf=Linux 2.6.32-38-generic uhci_hcd, prod=UHCI Host Controller, serial=0000:00:1d.2)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:007:002 (path=(null), vid=0b05, pid=1712, manuf=(null), prod=(null), serial=0194E8-5B-0002)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:007:003 (path=(null), vid=08ff, pid=1600, manuf=(null), prod=Fingerprint Sensor, serial=(null))                    
 [2013-12-13 12:02:51] lowlevel_scan: Found usb device at usb:002:001 (path=(null), vid=1d6b, pid=0002, manuf=Linux 2.6.32-38-generic ehci_hcd, prod=EHCI Host Controller, serial=0000:00:1d.7)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found hid device at hid:/dev/hidraw0 (path=/dev/hidraw0, vid=046d, pid=c03d, manuf=Logitech, prod=USB-PS/2 Optical Mouse, serial=(null))                    
 [2013-12-13 12:02:51] lowlevel_scan: Found hid device at hid:/dev/hidraw1 (path=/dev/hidraw1, vid=04d8, pid=00de, manuf=Microchip Technology Inc., prod=MCP2210 USB to SPI Master, serial=0000034904)                    
 [2013-12-13 12:02:51] lowlevel_scan: Found mcp2210 device at hid:/dev/hidraw1 (path=/dev/hidraw1, vid=04d8, pid=00de, manuf=Microchip Technology Inc., prod=MCP2210 USB to SPI Master, serial=0000034904)                    
Segmentation fault

and this is from a virtual machine with win 7 32 bit and bfgminer 3.8

Code:

[2013-12-13 12:19:14] setrlimit: Not supported by platform
 [2013-12-13 12:19:14] Started bfgminer 3.8.0
 [2013-12-13 12:19:14] usb_devinfo_scan: Error opening device usb:001:001: LIBUS
B_ERROR_NOT_SUPPORTED
 [2013-12-13 12:19:14] hidapi_try_lib: Couldn't load libhidapi.dll: unknown

 [2013-12-13 12:19:14] hidapi_try_lib: Successfully loaded libhidapi-0.dll

 [2013-12-13 12:19:14] hid_devinfo_scan: Found "MCP2210 USB to SPI Master" seria
l "0000034904"
 [2013-12-13 12:19:14] Failed to get PortName registry key value in lowl-vcom.c
_vcom_devinfo_scan_windows__hubport():443: The system cannot find the file speci
fied.
 [2013-12-13 12:19:14] FTD2XX.DLL failed to load, not using FTDI autodetect

 [2013-12-13 12:19:14] QueryDosDevice returned insufficent buffer error; enlargi
ng to 200
 [2013-12-13 12:19:14] QueryDosDevice returned insufficent buffer error; enlargi
ng to 400
 [2013-12-13 12:19:14] QueryDosDevice returned insufficent buffer error; enlargi
ng to 800
 [2013-12-13 12:19:14] QueryDosDevice returned insufficent buffer error; enlargi
ng to 1000
 [2013-12-13 12:19:14] QueryDosDevice returned insufficent buffer error; enlargi
ng to 2000
 [2013-12-13 12:19:14] lowlevel_scan: Found usb device at usb:001:002 (path=(nul
l), vid=04d8, pid=00de, manuf=Microchip Technology Inc., prod=MCP2210 USB to SPI
 Master, serial=0000034904)
 [2013-12-13 12:19:15] lowlevel_scan: Found usb device at usb:001:001 (path=(nul
l), vid=106b, pid=003f, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found hid device at hid:\\?\hid#vid_04d8&p
id_00de#6&8878c6a&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030} (path=\\?\hid#vi
d_04d8&pid_00de#6&8878c6a&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030}, vid=04d
8, pid=00de, manuf=Microchip Technology Inc., prod=MCP2210 USB to SPI Master, se
rial=0000034904)
 [2013-12-13 12:19:15] lowlevel_scan: Found mcp2210 device at hid:\\?\hid#vid_04
d8&pid_00de#6&8878c6a&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030} (path=\\?\hi
d#vid_04d8&pid_00de#6&8878c6a&0&0000#{4d1e55b2-f16f-11cf-88cb-001111000030}, vid
=04d8, pid=00de, manuf=Microchip Technology Inc., prod=MCP2210 USB to SPI Master
, serial=0000034904)
 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:11 (path=\\.\COM1
1, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:10 (path=\\.\COM1
0, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:9 (path=\\.\COM9,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:8 (path=\\.\COM8,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:7 (path=\\.\COM7,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:6 (path=\\.\COM6,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:5 (path=\\.\COM5,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:4 (path=\\.\COM4,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:3 (path=\\.\COM3,
 vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:16 (path=\\.\COM1
6, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:15 (path=\\.\COM1
5, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:14 (path=\\.\COM1
4, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:13 (path=\\.\COM1
3, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] lowlevel_scan: Found vcom device at com:12 (path=\\.\COM1
2, vid=0000, pid=0000, manuf=(null), prod=(null), serial=(null))

 [2013-12-13 12:19:15] Devices detected:
 [2013-12-13 12:19:15] Timers: Using QueryPerformanceCounter

 [2013-12-13 12:19:15] Recalibrating timeofday offset (delta 1386889520.706266s)

0 devices listed

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: berny81 on December 13, 2013, 06:15:15 AM

Quote from: loshia on December 13, 2013, 06:07:25 AM

Have you tried them one buy one just to make sure one of them not working
If no i suggest to try them one by one in same conditions even not changing port of the hub

Yes, i try it. on the same port the broken not working and other one work.

Unfortunately i think we will not be able to help you. It seems that this one is not OK ...
PS:
If someone can tell you how to program them and if or you find FW for pic it can solve your problem. But i do not know much about it

berny81

full member

Activity: 200

Merit: 100

Quote from: loshia on December 13, 2013, 06:07:25 AM

Have you tried them one buy one just to make sure one of them not working
If no i suggest to try them one by one in same conditions even not changing port of the hub

Yes, i try it. on the same port the broken not working and other one work.

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: berny81 on December 13, 2013, 05:33:39 AM

Quote from: Zich on December 13, 2013, 05:05:38 AM

Quote from: loshia on December 13, 2013, 05:00:21 AM

Quote from: Zich on December 13, 2013, 04:50:59 AM

Quote from: loshia on December 13, 2013, 04:41:44 AM

Quote from: berny81 on December 13, 2013, 04:35:21 AM

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

Hey,
Will you share here with us what is broken?
It may turn out that we can help?
10X

Yeah maybe some high quality picture, Or output from

Code:

bfgminer -D -d?

Nanos ?

If yoes i am counting on you Zich Wink

Yup, nanofury

yes we are talking about nanofury, tank you for try to help me.

i received 3 nanofury, i try it on 2 pc, 1 with win 7 32bit and bfgminer 3.8 and 1 with ubuntu 10.04 64 bit and bfgminer 3.8.
on both pc when i attach the 3 nanofury on win device manager i see all as HID device and on linux with lsusb -t i see all 3 as microchip device, but when i start bfgminer only 2 nanofury work, the third not appear in the list and when i add device from bfgminer while mining it say no device found.
I start bfgminer with -S all and setting osc bit 50
i use a Dlink DUB-H7 powered hub, i try all device connected, i try only two and only the broken to exclude power source problem but same result, 2 working and 1 not working, led remain off
now i can't post output of bfgminer -D because i have only the linux pc and bfgminer say segmentation fault when start with nanofury connected, i post it as soon as possible.
this evening i also post high quality picture.i compare the broken with the other one and i don't see solder problem or components broken,but i don't have expert eye

Have you tried them one buy one just to make sure one of them not working
If no i suggest to try them one by one in same conditions even not changing port of the hub

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: berny81 on December 13, 2013, 05:33:39 AM

yes we are talking about nanofury, tank you for try to help me.

i received 3 nanofury, i try it on 2 pc, 1 with win 7 32bit and bfgminer 3.8 and 1 with ubuntu 10.04 64 bit and bfgminer 3.8.
on both pc when i attach the 3 nanofury on win device manager i see all as HID device and on linux with lsusb -t i see all 3 as microchip device, but when i start bfgminer only 2 nanofury work, the third not appear in the list and when i add device from bfgminer while mining it say no device found.
I start bfgminer with -S all and setting osc bit 50
i use a Dlink DUB-H7 powered hub, i try all device connected, i try only two and only the broken to exclude power source problem but same result, 2 working and 1 not working, led remain off
now i can't post output of bfgminer -D because i have only the linux pc and bfgminer say segmentation fault when start with nanofury connected, i post it as soon as possible.
this evening i also post high quality picture.i compare the broken with the other one and i don't see solder problem or components broken,but i don't have expert eye

I was wondering if the problem nanofury had serial number on it because it's need serial number to work. You can check it using -D -d? .

berny81

full member

Activity: 200

Merit: 100

Quote from: Zich on December 13, 2013, 05:05:38 AM

Quote from: loshia on December 13, 2013, 05:00:21 AM

Quote from: Zich on December 13, 2013, 04:50:59 AM

Quote from: loshia on December 13, 2013, 04:41:44 AM

Quote from: berny81 on December 13, 2013, 04:35:21 AM

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

Hey,
Will you share here with us what is broken?
It may turn out that we can help?
10X

Yeah maybe some high quality picture, Or output from

Code:

bfgminer -D -d?

Nanos ?

If yoes i am counting on you Zich Wink

Yup, nanofury

yes we are talking about nanofury, tank you for try to help me.

i received 3 nanofury, i try it on 2 pc, 1 with win 7 32bit and bfgminer 3.8 and 1 with ubuntu 10.04 64 bit and bfgminer 3.8.
on both pc when i attach the 3 nanofury on win device manager i see all as HID device and on linux with lsusb -t i see all 3 as microchip device, but when i start bfgminer only 2 nanofury work, the third not appear in the list and when i add device from bfgminer while mining it say no device found.
I start bfgminer with -S all and setting osc bit 50
i use a Dlink DUB-H7 powered hub, i try all device connected, i try only two and only the broken to exclude power source problem but same result, 2 working and 1 not working, led remain off
now i can't post output of bfgminer -D because i have only the linux pc and bfgminer say segmentation fault when start with nanofury connected, i post it as soon as possible.
this evening i also post high quality picture.i compare the broken with the other one and i don't see solder problem or components broken,but i don't have expert eye

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: loshia on December 13, 2013, 05:00:21 AM

Quote from: Zich on December 13, 2013, 04:50:59 AM

Quote from: loshia on December 13, 2013, 04:41:44 AM

Quote from: berny81 on December 13, 2013, 04:35:21 AM

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

Hey,
Will you share here with us what is broken?
It may turn out that we can help?
10X

Yeah maybe some high quality picture, Or output from

Code:

bfgminer -D -d?

Nanos ?

If yoes i am counting on you Zich Wink

Yup, nanofury

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: Zich on December 13, 2013, 04:50:59 AM

Quote from: loshia on December 13, 2013, 04:41:44 AM

Quote from: berny81 on December 13, 2013, 04:35:21 AM

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

Hey,
Will you share here with us what is broken?
It may turn out that we can help?
10X

Yeah maybe some high quality picture, Or output from

Code:

bfgminer -D -d?

Nanos ?

If yoes i am counting on you Zich Wink

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: loshia on December 13, 2013, 04:41:44 AM

Quote from: berny81 on December 13, 2013, 04:35:21 AM

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

Hey,
Will you share here with us what is broken?
It may turn out that we can help?
10X

Yeah maybe some high quality picture, Or output from

Code:

bfgminer -D -d?

loshia

legendary

Activity: 1610

Merit: 1000

Quote from: berny81 on December 13, 2013, 04:35:21 AM

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

Hey,
Will you share here with us what is broken?
It may turn out that we can help?
10X

wuzamarine

sr. member

Activity: 264

Merit: 250

derp

Do NOT gaff me off. I will hurt your money.

Like you hurt mine.

berny81

full member

Activity: 200

Merit: 100

@marto74 why you reply only to people that accuse you to scam or people that use strong word for you?

i understand that you are very busy to maintein your agreements but i write to you in all possible way (mail, private message and then forum thread) and with patience i'm waiting your reply,but you are ignoring me.

i paid, but i have received some hardware BROKEN, i don't ask a refund for the moment, i only ask if there are something to do to make it functional.for a lot of day i can't use something that i have payd because you don't reply and you don't support your customers

wuzamarine

sr. member

Activity: 264

Merit: 250

derp

Here's your ripoff report.
http://www.ripoffreport.com/r/technobiteu/Select-StateProvince/technobiteu-technobiteu-ASIC-device-manufacturing-Total-cons-Just-take-your-money-and-1104203

you wanna keep playing games, or address the issue.

That one's got a week on it to salivate.

marto74

hero member

Activity: 728

Merit: 500

stop spamming everywhere.
Your first order is assembly service and we are waiting for your chips.
Both your second and third orders are December shipment and they will be shipped on time

Best Martin

braindead

sr. member

Activity: 452

Merit: 250

Hey marto you´re a scammer send my money back

Fu.. u and your comp...

i have a company in Portugal and i´ve never told my customers to fu»» off

You are ingrateful for your customers and a completly moro%

I´ve eARNED MY btc in gpu sooo

ZCVYIHWDO    2013-12-04    1 227,20€    bitpay    Payment accepted    Invoice PDF    details Reorder
CTSPMDNHN    2013-11-22    1 147,20€    Bank Wire    Payment accepted    Invoice PDF    details Reorder
RFEEXSMUR    2013-11-15    306,30€

return my fucking money dude

yyeaaahhh u have it?? im loosing here 0.5 btc for u .. u know what?? keeeo it in your ASS»»»»ho»»

marto74

hero member

Activity: 728

Merit: 500

Quote from: wuzamarine on December 12, 2013, 07:57:52 PM

Quote from: wuzamarine on December 12, 2013, 10:11:15 AM

I have sent you 30 emails on this borked order.

EDEGSUOLY    2013-12-06    999,90€    Bank Wire    Awaiting bank wire payment    -    details Reorder
substitute ^^ (referenced on the order last week)
YCCVEXVFJ    2013-12-03    1 323,30€    Bank Wire    Awaiting bank wire payment    -    details Reorder
cancel ^^ (referenced on the order last week)
LLLUVNLYK 2013-12-03    817,80€    bitpay    Payment accepted    Invoice PDF    details
cancel^^ (referenced on the order last week)

Why the hell can't you handle your business?

30 emails, 3 post now. This order is never going to get fixed.

When the payments have been done

wuzamarine

sr. member

Activity: 264

Merit: 250

derp

Quote from: wuzamarine on December 12, 2013, 10:11:15 AM

I have sent you 30 emails on this borked order.

EDEGSUOLY    2013-12-06    999,90€    Bank Wire    Awaiting bank wire payment    -    details Reorder
substitute ^^ (referenced on the order last week)
YCCVEXVFJ    2013-12-03    1 323,30€    Bank Wire    Awaiting bank wire payment    -    details Reorder
cancel ^^ (referenced on the order last week)
LLLUVNLYK 2013-12-03    817,80€    bitpay    Payment accepted    Invoice PDF    details
cancel^^ (referenced on the order last week)

Why the hell can't you handle your business?

30 emails, 3 post now. This order is never going to get fixed.

Melb

newbie

Activity: 58

Merit: 0

Also if you are using stratum pool (set bottom left) - you need to set top left pool setting to localhost to use the stratum proxy... Clicking the start button bottom left should launch the proxy (or keep the autostart ticked)...

Melb

Melb

newbie

Activity: 58

Merit: 0

You have Avalon selected - Shouldn't that be Bitfury with the HEX16B?

Melb

SpAcEDeViL

legendary

Activity: 986

Merit: 1027

Miner-Control.de Pooler

Hy,

The HEX16B has arrived. On first run i become only 8 GHs and 11-12 aktive chips from 16.

But now i become only HW-Errors in HEXMiner under Win7.

Topic: [ANN] Technobit HEX16B(Bitfury based) 16 chip board design - page 27. (Read 56539 times)