Pages:
Author

Topic: Avalon ASIC users thread - page 13. (Read 438575 times)

newbie
Activity: 30
Merit: 0
January 19, 2015, 11:52:37 PM
New MM firmware released for Avalon4, Hardware model: MM-4.1, Version: 411501-d17f4a10

Firmware Details:
    http://downloads.canaan-creative.com/software/avalon4/mm41/2015-01-15/

ChangeLog:
* Fix negative temperature.
* Add new command for MM I2C TX FIFO reset.

Fengling
newbie
Activity: 30
Merit: 0
January 19, 2015, 11:43:26 PM
New MM firmware released for Avalon4, Hardware model: MM-4.0, Version: 401501-4778d610

Firmware Details:
    http://downloads.canaan-creative.com/software/avalon4/mm/2015-01-19/

ChangeLog:
* Support voltage adjustion by miners.
* Move the frequency table to CGMiner.
* Turn down LM32 CPU frequency from 100MHz to 50MHz.
* Update the ASIC clock configure method, more friendly with power supply module.
* Fix LED warning blink when get new stratum.
* Move the miner's Localwork statistics to Verilog HDL side.
* Fix negative temperature.
* Add new command for MM I2C TX FIFO reset.

Fengling
newbie
Activity: 30
Merit: 0
January 19, 2015, 11:29:26 PM
New firmware released for Avalon4 RPi/703N, Version: Canaan A4-20150119

Firmware Details:
RPi/703N Firmware
    http://downloads.canaan-creative.com/software/avalon4/openwrt/20150119_1609/

ChangeLog:
* Support automatic adjust voltage individually(Support on MM4.1, MM4.0(>401501-d17f4a10)).
* Support MM firmware upgrade through LuCI(Caution:Only for professional users!!!).
* Fix temperature display when it is < 0C.
* Fix WiFi cann't work on TL-WR703N.
* Add more mining mode.
* Update the module set_voltage method to one by one.
* Change localwork statistics from software to hardware.

Fengling
newbie
Activity: 30
Merit: 0
December 15, 2014, 01:23:13 AM
New MM firmware released for Avalon4, Hardware model: MM-4.0, Version: 401412-7ef4ab10

Firmware Details:
   http://downloads.canaan-creative.com/software/avalon4/mm/2014-12-13/

ChangeLog:
* Support MBOOT
* Keep the nonce2_offse and nonce2_range since g_module_id didn't change
* Keep mm working when temp is greater than IDLE_TEMP
* Add parameter for test core count
* Warning when no fan connect

Fengling
newbie
Activity: 30
Merit: 0
December 15, 2014, 12:01:37 AM
New firmware released for Avalon4 RPi/703N, Version: Canaan A4-20141213

Firmware Details:
RPi/703N Firmware
   http://downloads.canaan-creative.com/software/avalon4/openwrt/20141213_1015/

ChangeLog:
* Improve the voltage increase adjustment
* Fix duplicated local work & error work
* Fix the default settings of new module
* Support MM41
* Optimise the process of cgminer-status
* Add UI for password change
* Fix the Avalon index page

Fengling
newbie
Activity: 30
Merit: 0
November 28, 2014, 03:58:40 AM
The first stable Avalon4 RPi/703N firmware released. Version: Canaan A4-20141127

Details:
RPi/703N Firmware
   http://downloads.canaan-creative.com/software/avalon4/openwrt/20141127_1341/
MM Firmware
   http://downloads.canaan-creative.com/software/avalon4/mm/2014-11-22/

Feature:
* Support TL-WR703N, Raspberry Pi B/B+
* Latest cgminer, version: 4.7.0
* Latest OpenWrt, version: r43076
* Brand new GUI
* Brand new usb converter: AUC
* Support up to 9 Avalon4-1T machines in one AUC chain with automatical ID assignment
* One RPi/703N can handle up to 100 Avalon4-1T machines
* AUC hotplug
* Avalon4-1T module hotplug
* Adjust module's voltage automatically for power optimization
* Brand new MM protocol,support voltage/frequency/fan adjustment per module


Default Configuration:
* Chip Frequency        8125
* Chip Voltage            445:385:370
* Automatic Voltage    True
* Fan                         20-100

Be careful with your TL-WR703N's old configuration.
newbie
Activity: 29
Merit: 0
November 13, 2014, 12:39:28 PM
Can the Avalon Openwrt version running on TL-WR703N be converted back to standard Openwrt?
I have bricked 6 devices so far trying.

I picked up a bunch of Avalon TL-WR703N and each one keeps getting bricked as I try to recover them back to a standard openwrt firmware so I can then upgrade using my own image builder build.

https://forum.openwrt.org/viewtopic.php?pid=254109#p254109

I tried today, the u-boot method but am getting nowhere.

Picked up the files mentioned in this post;
https://forum.openwrt.org/viewtopic.php?id=48169

Gave it a try but ended up with an error;

3840 -rw-r--r--    1 root     root       3932160 Jan  1 10:05 factory.bin
    64 -rw-r--r--    1 root     root         65536 Jan  1 10:06 uboot_for_tp-link_tl-wr703n.bin
     4 -rw-r--r--    1 root     root            66 Jan  1 10:06 uboot_for_tp-link_tl-wr703n.md5

# md5sum uboot_for_tp-link_tl-wr703n.bin
5799189400ee774c45bd0bfb79ef9ffd  uboot_for_tp-link_tl-wr703n.bin

# dd if=/dev/mtd0 of=uboot_orig.bin
256+0 records in
256+0 records out

# cp uboot_orig.bin uboot_new.bin

# dd if=uboot_for_tp-link_tl-wr703n.bin of=uboot_new.bin conv=notrunc
128+0 records in
128+0 records out

# mtd write uboot_orig.bin "u-boot"
Could not open mtd device: u-boot
Can't open device for writing!
full member
Activity: 120
Merit: 100
September 17, 2014, 12:49:53 AM
Please check this URL: http://downloads.canaan-creative.com/, It have the correct firmware under the machine name.

Xiangfu


I recently acquired an Avalon 2 (200GH) clone and want to update software. Do I just download this file....openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin.....or others as well within the folder...never done it before I am an Avalon newbie.....thanks
sr. member
Activity: 309
Merit: 250
September 05, 2014, 03:14:09 AM
A new firmware come out: 2014-08-27 (More features)
Hi, All:

Firmware NEWS

Please update your firmware if you have an Avalon3 machine.

Downloads:
   http://downloads.canaan-creative.com/

ChangeLog:
   Merge cgminer to ckolivas's trunk(V4.5.0)
   Support p2pool(with MM Version: 331408-a15cac80)
   Fan speed auto adjust with new method,range support.(cgminer param: --avalon2-fan 50-100 or --avalon2-fan 50)
   Support hotplug usb cable by cgminer.
   Ignore blacklisted and zombie devices on luci status page.

See https://en.bitcoin.it/wiki/Avalon2#Firmware for more information.

Communicate:
   http://lists.canaan-creative.com/cgi-bin/mailman/listinfo
   IRC: #avalon @freenode.net

Documents:
   https://en.bitcoin.it/wiki/Avalon

Mikeqin

I recently acquired an Avalon 2 (200GH) clone and want to update software. Do I just download this file....openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin.....or others as well within the folder...never done it before I am an Avalon newbie.....thanks
newbie
Activity: 30
Merit: 0
September 02, 2014, 09:30:04 PM
A new firmware come out: 2014-08-27 (More features)
Hi, All:

Firmware NEWS

Please update your firmware if you have an Avalon3 machine.

Downloads:
   http://downloads.canaan-creative.com/

ChangeLog:
   Merge cgminer to ckolivas's trunk(V4.5.0)
   Support p2pool(with MM Version: 331408-a15cac80)
   Fan speed auto adjust with new method,range support.(cgminer param: --avalon2-fan 50-100 or --avalon2-fan 50)
   Support hotplug usb cable by cgminer.
   Ignore blacklisted and zombie devices on luci status page.

See https://en.bitcoin.it/wiki/Avalon2#Firmware for more information.

Communicate:
   http://lists.canaan-creative.com/cgi-bin/mailman/listinfo
   IRC: #avalon @freenode.net

Documents:
   https://en.bitcoin.it/wiki/Avalon

Mikeqin
legendary
Activity: 1246
Merit: 1002
August 24, 2014, 08:18:15 AM
Can some one help take a look at my logs. Something is wrong. Getting 0 GH/s. Help will be rewarded BTC.

Finally got my rig connected to the pool. But now it does not seem to be mining. Why is MHS5sec = 0.
Link to Dashboard Screenshot:
https://drive.google.com/file/d/0BxmU6_TGSM0wNi12TWZpRkg3cWc/edit?usp=sharing



I notice that match_work 17-32 are all 0, and some of the match work 1-16 are also 0.  The screen shot shows a lot of HW errors.

When you mention "finally got it connected" I think perhaps the unit has never worked in your possession, so perhaps it was recently shipped.

The Avalons seemed to have a lot of reports of connections becoming loose during shipping.  You might open the case and reseat everything.

Also, since it is reporting HW failure, I would set the frequency to a low value.  I can't tell if this is an Avalon 1 or an Avalon 2.  The 282 MHz value is too high for an Avalon 1.


newbie
Activity: 3
Merit: 0
August 23, 2014, 07:37:35 PM
Can some one help take a look at my logs. Something is wrong. Getting 0 GH/s. Help will be rewarded BTC.

Finally got my rig connected to the pool. But now it does not seem to be mining. Why is MHS5sec = 0.
Link to Dashboard Screenshot:
https://drive.google.com/file/d/0BxmU6_TGSM0wNi12TWZpRkg3cWc/edit?usp=sharing

Here is the CGminer api log:
Code:
[Firmware Version] => 20131229
cgminer: 698d677
cgminer-openwrt-packages: aadd747+
luci: 346e3e7+
Reply was 'STATUS=S,When=1408839699,Code=70,Msg=CGMiner stats,Description=cgminer 3.9.0|STATS=0,ID=AVA0,Elapsed=87,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,baud=115200,miner_count=32,asic_count=10,timeout=45,frequency=282,fan1=0,fan2=0,fan3=0,temp1=0,temp2=0,temp3=0,temp_max=0,Device Hardware%=100.0000,no_matching_work=2,match_work_count1=42,match_work_count2=37,match_work_count3=32,match_work_count4=44,match_work_count5=40,match_work_count6=0,match_work_count7=37,match_work_count8=50,match_work_count9=0,match_work_count10=41,match_work_count11=34,match_work_count12=42,match_work_count13=39,match_work_count14=31,match_work_count15=38,match_work_count16=44,match_work_count17=0,match_work_count18=0,match_work_count19=0,match_work_count20=0,match_work_count21=0,match_work_count22=0,match_work_count23=0,match_work_count24=0,match_work_count25=0,match_work_count26=0,match_work_count27=0,match_work_count28=0,match_work_count29=0,match_work_count30=0,match_work_count31=0,match_work_count32=0,Controller Version=0,Avalon Chip=110,USB Pipe=0,USB Delay=r0 0.000000 w0 0.000000,USB tmo=2122 0|STATS=1,ID=POOL0,Elapsed=87,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=1024.00000000,Min Diff=1024.00000000,Max Diff=1024.00000000,Min Diff Count=632,Max Diff Count=632,Times Sent=2,Bytes Sent=142,Times Recv=8,Bytes Recv=4340,Net Bytes Sent=142,Net Bytes Recv=4340|STATS=2,ID=POOL1,Elapsed=87,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=1024.00000000,Min Diff=1024.00000000,Max Diff=1024.00000000,Min Diff Count=632,Max Diff Count=632,Times Sent=2,Bytes Sent=142,Times Recv=6,Bytes Recv=2328,Net Bytes Sent=142,Net Bytes Recv=2328|STATS=3,ID=POOL2,Elapsed=87,Calls=0,Wait=0.000000,Max=0.000000,Min=99999999.000000,Pool Calls=0,Pool Attempts=0,Pool Wait=0.000000,Pool Max=0.000000,Pool Min=99999999.000000,Pool Av=0.000000,Work Had Roll Time=false,Work Can Roll=false,Work Had Expire=false,Work Roll Time=0,Work Diff=1024.00000000,Min Diff=1024.00000000,Max Diff=1024.00000000,Min Diff Count=632,Max Diff Count=632,Times Sent=2,Bytes Sent=142,Times Recv=8,Bytes Recv=4273,Net Bytes Sent=142,Net Bytes Recv=4273|'
[STATUS] =>
(
   [STATUS] => S
   [When] => 1408839699
   [Cde] => 70
   [Msg] => CGMiner stats
   [Description] => cgminer 3.9.0
)
[STATS0] =>
(
   [STATS] => 0
   [ID] => AVA0
   [Elapsed] => 87
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [baud] => 115200
   [miner_count] => 32
   [asic_count] => 10
   [timeout] => 45
   [frequency] => 282
   [fan1] => 0
   [fan2] => 0
   [fan3] => 0
   [temp1] => 0
   [temp2] => 0
   [temp3] => 0
   [temp_max] => 0
   [Device Hardware%] => 100.0000
   [no_matching_work] => 2
   [match_work_count1] => 42
   [match_work_count2] => 37
   [match_work_count3] => 32
   [match_work_count4] => 44
   [match_work_count5] => 40
   [match_work_count6] => 0
   [match_work_count7] => 37
   [match_work_count8] => 50
   [match_work_count9] => 0
   [match_work_count10] => 41
   [match_work_count11] => 34
   [match_work_count12] => 42
   [match_work_count13] => 39
   [match_work_count14] => 31
   [match_work_count15] => 38
   [match_work_count16] => 44
   [match_work_count17] => 0
   [match_work_count18] => 0
   [match_work_count19] => 0
   [match_work_count20] => 0
   [match_work_count21] => 0
   [match_work_count22] => 0
   [match_work_count23] => 0
   [match_work_count24] => 0
   [match_work_count25] => 0
   [match_work_count26] => 0
   [match_work_count27] => 0
   [match_work_count28] => 0
   [match_work_count29] => 0
   [match_work_count30] => 0
   [match_work_count31] => 0
   [match_work_count32] => 0
   [Controller Version] => 0
   [Avalon Chip] => 110
   [USB Pipe] => 0
   [USB Delay] => r0 0.000000 w0 0.000000
   [USB tmo] => 2122 0
)
[STATS1] =>
(
   [STATS] => 1
   [ID] => POOL0
   [Elapsed] => 87
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [Pool Calls] => 0
   [Pool Attempts] => 0
   [Pool Wait] => 0.000000
   [Pool Max] => 0.000000
   [Pool Min] => 99999999.000000
   [Pool Av] => 0.000000
   [Work Had Roll Time] => false
   [Work Can Roll] => false
   [Work Had Expire] => false
   [Work Roll Time] => 0
   [Work Diff] => 1024.00000000
   [Min Diff] => 1024.00000000
   [Max Diff] => 1024.00000000
   [Min Diff Count] => 632
   [Max Diff Count] => 632
   [Times Sent] => 2
   [Bytes Sent] => 142
   [Times Recv] => 8
   [Bytes Recv] => 4340
   [Net Bytes Sent] => 142
   [Net Bytes Recv] => 4340
)
[STATS2] =>
(
   [STATS] => 2
   [ID] => POOL1
   [Elapsed] => 87
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [Pool Calls] => 0
   [Pool Attempts] => 0
   [Pool Wait] => 0.000000
   [Pool Max] => 0.000000
   [Pool Min] => 99999999.000000
   [Pool Av] => 0.000000
   [Work Had Roll Time] => false
   [Work Can Roll] => false
   [Work Had Expire] => false
   [Work Roll Time] => 0
   [Work Diff] => 1024.00000000
   [Min Diff] => 1024.00000000
   [Max Diff] => 1024.00000000
   [Min Diff Count] => 632
   [Max Diff Count] => 632
   [Times Sent] => 2
   [Bytes Sent] => 142
   [Times Recv] => 6
   [Bytes Recv] => 2328
   [Net Bytes Sent] => 142
   [Net Bytes Recv] => 2328
)
[STATS3] =>
(
   [STATS] => 3
   [ID] => POOL2
   [Elapsed] => 87
   [Calls] => 0
   [Wait] => 0.000000
   [Max] => 0.000000
   [Min] => 99999999.000000
   [Pool Calls] => 0
   [Pool Attempts] => 0
   [Pool Wait] => 0.000000
   [Pool Max] => 0.000000
   [Pool Min] => 99999999.000000
   [Pool Av] => 0.000000
   [Work Had Roll Time] => false
   [Work Can Roll] => false
   [Work Had Expire] => false
   [Work Roll Time] => 0
   [Work Diff] => 1024.00000000
   [Min Diff] => 1024.00000000
   [Max Diff] => 1024.00000000
   [Min Diff Count] => 632
   [Max Diff Count] => 632
   [Times Sent] => 2
   [Bytes Sent] => 142
   [Times Recv] => 8
   [Bytes Recv] => 4273
   [Net Bytes Sent] => 142
   [Net Bytes Recv] => 4273
)
newbie
Activity: 53
Merit: 0
July 20, 2014, 11:19:23 PM
Avalon2/Avalon3: A new firmware come out: 2014-07-19

Downloads:
    http://downloads.canaan-creative.com/software/avalon2/2014-07-19/

ChangeLog:
   Update OpenWrt to r41240
   Add new parameter for polling delay: --avalon2-polling-delay (Default: 20ms)
   Add new parameter for stratum ignore time: --stratum-ignore (Default: 30s)
   Add LED status on API log
   Support unlimited socket receive size for cgminer-api
   Try to detect module twice when start
   Don't count HW works on hashrate
   Support cgminer restart on status page
   Display indicator status on status page
   Change introduction on luci-cgminer


Communicate:
    http://lists.canaan-creative.com/cgi-bin/mailman/listinfo
    IRC: #avalon @freenode.net

Documents:
    https://en.bitcoin.it/wiki/Avalon


archang

Thank you for this good share, these updates is good appeal for pre-buyers like me.
newbie
Activity: 1
Merit: 0
July 20, 2014, 11:16:00 PM
Avalon2/Avalon3: A new firmware come out: 2014-07-19

Downloads:
    http://downloads.canaan-creative.com/software/avalon2/2014-07-19/

ChangeLog:
   Update OpenWrt to r41240
   Add new parameter for polling delay: --avalon2-polling-delay (Default: 20ms)
   Add new parameter for stratum ignore time: --stratum-ignore (Default: 30s)
   Add LED status on API log
   Support unlimited socket receive size for cgminer-api
   Try to detect module twice when start
   Don't count HW works on hashrate
   Support cgminer restart on status page
   Display indicator status on status page
   Change introduction on luci-cgminer


Communicate:
    http://lists.canaan-creative.com/cgi-bin/mailman/listinfo
    IRC: #avalon @freenode.net

Documents:
    https://en.bitcoin.it/wiki/Avalon


archang
newbie
Activity: 4
Merit: 0
June 26, 2014, 09:24:37 PM
Wunderbar!!!

It worked!

Thanks!
newbie
Activity: 56
Merit: 0
June 26, 2014, 03:37:44 AM
Hello,

If you have avalon 2 chips on avalon 1 board use this firmware.

http://downloads.canaan-creative.com/software/avalon1/20140227/openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin

It solves problem with my machine, is buggy but it work. I have avalon 2 machine 200G. You can see on this link http://downloads.canaan-creative.com/# that avalon 2 on 200gh use this firmware.

I also try avalon 2 firmwares but no one working. Good luck Smiley
newbie
Activity: 4
Merit: 0
June 25, 2014, 11:07:58 PM
Updated to the factory version of 20140526

Still same behavior with Updated code  Embarrassed

CGMiner API Log
[Firmware Version] => 20140526
cgminer: 444d457
cgminer-openwrt-packages: b7b7afe
luci: b66161d
Socket connect failed: Connection refused

CGMiner settings sans/personal info:
Pool1: stratum+tcp://stratum.btcguild.com:3333
Pool Balance(Default: Failover): Balance
Chip Frequency(Avalon2: 1500, Avalon3: 450): 1300
Chip Voltage(Avalon2: 10000, Avalon3: 6625): 10000
Fan%(Default: 90%): 90
API Allow(Default: W:127.0.0.1):  W:127.0.0.1
More Options(Default: --quiet): --real-quiet

Latest System_Log:
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.560000] ath: EEPROM regdomain: 0x0
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.560000] ath: EEPROM indicates default country code should be used
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.560000] ath: doing EEPROM country->regdmn map search
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.560000] ath: country maps to regdmn code: 0x3a
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.560000] ath: Country alpha2 being used: US
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.560000] ath: Regpair used: 0x3a
Wed Jun 25 21:56:48 2014 kern.debug kernel: [   11.570000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.580000] cfg80211: Calling CRDA for country: US
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.580000] cfg80211: Regulatory domain changed to country: US
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.590000] cfg80211:  DFS Master region: FCC
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.590000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.600000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.610000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.620000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.630000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.630000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Wed Jun 25 21:56:48 2014 kern.info kernel: [   11.640000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Wed Jun 25 21:56:48 2014 user.emerg syslog: Error: Failed to connect to ubus
Wed Jun 25 21:56:50 2014 user.emerg syslog: uinteger - 8 = true
Wed Jun 25 21:56:50 2014 daemon.err odhcpd[659]: Failed to open routing table: No such file or directory
Wed Jun 25 21:56:50 2014 daemon.err odhcpd[659]: Unable to open raw socket: Address family not supported by protocol
Wed Jun 25 21:56:51 2014 cron.info crond[680]: crond: crond (busybox 1.22.1) started, log level 8
Wed Jun 25 21:56:51 2014 authpriv.info dropbear[695]: Not backgrounding
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'lan' is enabled
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'loopback' is enabled
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Network device 'lo' link is up
Wed Jun 25 21:56:54 2014 kern.info kernel: [   19.980000] device eth0 entered promiscuous mode
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'loopback' has link connectivity
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'loopback' is setting up now
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'loopback' is now up
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: bad address '3.openwrt.pool.ntp.org'
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: could not resolve peer 3.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: bad address '1.openwrt.pool.ntp.org'
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: could not resolve peer 1.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: bad address '0.openwrt.pool.ntp.org'
Wed Jun 25 21:56:54 2014 user.emerg syslog: ntpd: could not resolve peer 0.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:56:54 2014 kern.info kernel: [   20.470000] eth0: link up (100Mbps/Full duplex)
Wed Jun 25 21:56:54 2014 kern.info kernel: [   20.470000] br-lan: port 1(eth0) entered forwarding state
Wed Jun 25 21:56:54 2014 kern.info kernel: [   20.480000] br-lan: port 1(eth0) entered forwarding state
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Network device 'eth0' link is up
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Bridge 'br-lan' link is up
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'lan' has link connectivity
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'lan' is setting up now
Wed Jun 25 21:56:54 2014 daemon.notice netifd: Interface 'lan' is now up
Wed Jun 25 21:56:55 2014 user.emerg syslog: 'radio0' is disabled
Wed Jun 25 21:56:55 2014 user.emerg syslog: 'radio0' is disabled
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: started, version 2.71 cachesize 150
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: using local addresses only for domain lan
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: reading /tmp/resolv.conf.auto
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: using local addresses only for domain lan
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: using nameserver 192.168.0.1#53
Wed Jun 25 21:56:55 2014 daemon.info dnsmasq[828]: read /etc/hosts - 1 addresses
Wed Jun 25 21:56:55 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Wed Jun 25 21:56:55 2014 daemon.err odhcpd[867]: Failed to open routing table: No such file or directory
Wed Jun 25 21:56:55 2014 daemon.err odhcpd[867]: Unable to open raw socket: Address family not supported by protocol
Wed Jun 25 21:56:56 2014 kern.info kernel: [   22.480000] br-lan: port 1(eth0) entered forwarding state
Wed Jun 25 21:57:00 2014 daemon.err odhcpd[885]: Failed to open routing table: No such file or directory
Wed Jun 25 21:57:00 2014 daemon.err odhcpd[885]: Unable to open raw socket: Address family not supported by protocol
Wed Jun 25 21:57:20 2014 daemon.err odhcpd[890]: Failed to open routing table: No such file or directory
Wed Jun 25 21:57:20 2014 daemon.err odhcpd[890]: Unable to open raw socket: Address family not supported by protocol
Wed Jun 25 21:57:25 2014 daemon.err odhcpd[897]: Failed to open routing table: No such file or directory
Wed Jun 25 21:57:25 2014 daemon.err odhcpd[897]: Unable to open raw socket: Address family not supported by protocol
Wed Jun 25 21:57:30 2014 daemon.err odhcpd[922]: Failed to open routing table: No such file or directory
Wed Jun 25 21:57:30 2014 daemon.err odhcpd[922]: Unable to open raw socket: Address family not supported by protocol
Wed Jun 25 21:57:30 2014 user.emerg syslog: Instance odhcpd::instance1 s in a crash loop 6 crashes, 0 seconds since last crash
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 173.230.144.109
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: sending query to 173.230.144.109
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 50.97.210.169
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: sending query to 50.97.210.169
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 76.73.0.4
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: sending query to 76.73.0.4
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: reply from 173.230.144.109: offset:-0.171055 delay:0.440123 status:0x24 strat:3 refid:0xd0c9f202 rootdelay:0.004669 reach:0x01
Wed Jun 25 21:57:44 2014 user.emerg syslog: ntpd: reply from 50.97.210.169: offset:-0.062920 delay:0.213659 status:0x24 strat:2 refid:0xd133a1ee rootdelay:0.072099 reach:0x01
Wed Jun 25 21:57:44 2014 user.emerg syslog: Alarm clock
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 173.230.144.109
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: sending query to 173.230.144.109
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 50.97.210.169
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: sending query to 50.97.210.169
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 76.73.0.4
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: sending query to 76.73.0.4
Wed Jun 25 21:58:14 2014 user.emerg syslog: ntpd: reply from 173.230.144.109: offset:+0.019948 delay:0.057040 status:0x24 strat:3 refid:0xd0c9f202 rootdelay:0.004669 reach:0x01
Wed Jun 25 21:58:14 2014 user.emerg syslog: Alarm clock
Wed Jun 25 21:58:16 2014 cron.info crond[680]: crond: USER root pid 1168 cmd /usr/bin/cgminer-monitor
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 208.75.88.4
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: sending query to 208.75.88.4
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 173.230.144.178
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: sending query to 173.230.144.178
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 199.7.177.206
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: sending query to 199.7.177.206
Wed Jun 25 21:58:44 2014 user.emerg syslog: ntpd: reply from 208.75.88.4: offset:+0.010493 delay:0.053818 status:0x24 strat:2 refid:0x8009b01e rootdelay:0.002029 reach:0x01
Wed Jun 25 21:58:44 2014 user.emerg syslog: Alarm clock
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 173.230.144.109
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: sending query to 173.230.144.109
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 108.61.73.244
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: sending query to 108.61.73.244
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 69.41.163.31
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: sending query to 69.41.163.31
Wed Jun 25 21:59:15 2014 user.emerg syslog: ntpd: reply from 173.230.144.109: offset:-0.071335 delay:0.239691 status:0x24 strat:3 refid:0xd0c9f202 rootdelay:0.004669 reach:0x01
Wed Jun 25 21:59:15 2014 user.emerg syslog: Alarm clock
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 173.230.144.109
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: sending query to 173.230.144.109
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 108.61.73.244
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: sending query to 108.61.73.244
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 199.7.177.206
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: sending query to 199.7.177.206
Wed Jun 25 21:59:45 2014 user.emerg syslog: ntpd: reply from 173.230.144.109: offset:+0.019239 delay:0.057022 status:0x24 strat:3 refid:0xd0c9f202 rootdelay:0.004669 reach:0x01
Wed Jun 25 21:59:45 2014 user.emerg syslog: Alarm clock
Wed Jun 25 22:00:01 2014 cron.info crond[680]: crond: user root: process already running: /usr/bin/cgminer-monitor
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 208.75.89.4
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: sending query to 208.75.89.4
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 64.246.132.14
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: sending query to 64.246.132.14
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 69.41.163.31
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: sending query to 69.41.163.31
Wed Jun 25 22:00:15 2014 user.emerg syslog: ntpd: reply from 208.75.89.4: offset:+0.010801 delay:0.054664 status:0x24 strat:2 refid:0xce751914 rootdelay:0.004578 reach:0x01
Wed Jun 25 22:00:15 2014 user.emerg syslog: Alarm clock
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 173.230.144.109
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: sending query to 173.230.144.109
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 108.61.73.244
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: sending query to 108.61.73.244
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 199.7.177.206
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: sending query to 199.7.177.206
Wed Jun 25 22:00:45 2014 user.emerg syslog: ntpd: reply from 173.230.144.109: offset:+0.019156 delay:0.056624 status:0x24 strat:3 refid:0xd0c9f202 rootdelay:0.004669 reach:0x01
Wed Jun 25 22:00:45 2014 user.emerg syslog: Alarm clock
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 208.75.89.4
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: sending query to 208.75.89.4
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 64.246.132.14
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: sending query to 64.246.132.14
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 64.71.152.181
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: sending query to 64.71.152.181
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: reply from 208.75.89.4: offset:-0.018493 delay:0.104117 status:0x24 strat:2 refid:0xce751914 rootdelay:0.004578 reach:0x01
Wed Jun 25 22:01:15 2014 user.emerg syslog: ntpd: reply from 64.246.132.14: offset:-0.002182 delay:0.100866 status:0x24 strat:1 refid:0x43444d41 rootdelay:0.000000 reach:0x01
Wed Jun 25 22:01:15 2014 user.emerg syslog: Alarm clock
Wed Jun 25 22:01:45 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 22:01:45 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 22:01:45 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 216.66.0.142
Wed Jun 25 22:01:45 2014 user.emerg syslog: ntpd: sending query to 216.66.0.142
Wed Jun 25 22:01:45 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 64.246.132.14
Wed Jun 25 22:01:45 2014 user.emerg syslog: ntpd: sending query to 64.246.132.14
Wed Jun 25 22:01:46 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 64.71.152.181
Wed Jun 25 22:01:46 2014 user.emerg syslog: ntpd: sending query to 64.71.152.181
Wed Jun 25 22:01:46 2014 user.emerg syslog: ntpd: reply from 216.66.0.142: offset:-0.037225 delay:0.176683 status:0x24 strat:2 refid:0xc862c4d4 rootdelay:0.018051 reach:0x01
Wed Jun 25 22:01:46 2014 user.emerg syslog: Alarm clock
Wed Jun 25 22:02:01 2014 cron.info crond[680]: crond: user root: process already running: /usr/bin/cgminer-monitor
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 67.18.187.111
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: sending query to 67.18.187.111
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 198.58.100.198
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: sending query to 198.58.100.198
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 69.129.251.133
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: sending query to 69.129.251.133
Wed Jun 25 22:02:16 2014 user.emerg syslog: ntpd: reply from 67.18.187.111: offset:-0.002477 delay:0.059648 status:0x24 strat:2 refid:0x1838b28c rootdelay:0.025895 reach:0x01
Wed Jun 25 22:02:16 2014 user.emerg syslog: Alarm clock
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: bad address '4.openwrt.pool.ntp.org'
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: could not resolve peer 4.openwrt.pool.ntp.org, skipping
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: resolved peer 3.openwrt.pool.ntp.org to 198.55.111.50
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: sending query to 198.55.111.50
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: resolved peer 1.openwrt.pool.ntp.org to 50.97.210.169
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: sending query to 50.97.210.169
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: resolved peer 0.openwrt.pool.ntp.org to 64.71.152.181
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: sending query to 64.71.152.181
Wed Jun 25 22:02:46 2014 user.emerg syslog: ntpd: reply from 198.55.111.50: offset:+0.006290 delay:0.053633 status:0x24 strat:3 refid:0xd8e50032 rootdelay:0.051606 reach:0x01
Wed Jun 25 22:02:46 2014 user.emerg syslog: Alarm clock




Kernel Log:
[    0.000000] Linux version 3.10.36 ([email protected]) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r40859) ) #2 Mon May 26 19:46:39 CST 2014
[    0.000000] MyLoader: sysp=388dd517, boardp=04505212, parts=7709ac36
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 803065b0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc:
  • 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28784k/32768k available (2210k kernel code, 3984k reserved, 589k data, 268k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.350000] bio: create slab at 0
[    0.360000] Switching to clocksource MIPS
[    0.360000] NET: Registered protocol family 2
[    0.370000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.370000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.370000] TCP: Hash tables configured (established 512 bind 512)
[    0.380000] TCP: reno registered
[    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] NET: Registered protocol family 1
[    0.400000] PCI: CLS 0 bytes, default 32
[    0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 56
[    0.440000] io scheduler noop registered
[    0.440000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.450000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.460000] console [ttyATH0] enabled, bootconsole disabled
[    0.470000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.480000] m25p80 spi0.0: found s25sl032p, expected m25p80
[    0.480000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[    0.490000] 5 tp-link partitions found on MTD device spi0.0
[    0.490000] Creating 5 MTD partitions on "spi0.0":
[    0.500000] 0x000000000000-0x000000020000 : "u-boot"
[    0.500000] 0x000000020000-0x00000011bffc : "kernel"
[    0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.520000] 0x00000011bffc-0x0000003f0000 : "rootfs"
[    0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.540000] mtd: device 2 (rootfs) set to be root filesystem
[    0.540000] 1 squashfs-split partitions found on MTD device rootfs
[    0.550000] 0x000000360000-0x0000003f0000 : "rootfs_data"
[    0.560000] 0x0000003f0000-0x000000400000 : "art"
[    0.560000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.580000] libphy: ag71xx_mdio: probed
[    1.140000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.150000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.150000] TCP: cubic registered
[    1.160000] NET: Registered protocol family 17
[    1.160000] 8021q: 802.1Q VLAN Support v1.8
[    1.170000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.180000] Freeing unused kernel memory: 268K (8031d000 - 80360000)
[    4.890000] usbcore: registered new interface driver usbfs
[    4.900000] usbcore: registered new interface driver hub
[    4.900000] usbcore: registered new device driver usb
[    4.920000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.920000] ehci-platform: EHCI generic platform driver
[    4.930000] ehci-platform ehci-platform: EHCI Host Controller
[    4.930000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.940000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    4.970000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    4.970000] hub 1-0:1.0: USB hub found
[    4.970000] hub 1-0:1.0: 1 port detected
[    5.300000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    5.450000] hub 1-1:1.0: USB hub found
[    5.450000] hub 1-1:1.0: 2 ports detected
[    5.730000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[    7.180000] eth0: link up (100Mbps/Full duplex)
[    8.190000] jffs2: notice: (307) jffs2_build_xattr_subsystem: complete building xattr subsystem, 20 of xdatum (0 unchecked, 19 orphan) and 51 of xref (0 dead, 34 orphan) found.
[    8.230000] eth0: link down
[   11.150000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   11.160000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   11.170000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
[   11.200000] usbcore: registered new interface driver usbserial
[   11.200000] usbcore: registered new interface driver usbserial_generic
[   11.210000] usbserial: USB Serial support registered for generic
[   11.240000] xt_time: kernel timezone is -0000
[   11.280000] cfg80211: Calling CRDA to update world regulatory domain
[   11.280000] cfg80211: World regulatory domain updated:
[   11.290000] cfg80211:  DFS Master region: unset
[   11.290000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   11.300000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   11.310000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   11.320000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   11.320000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   11.330000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   11.340000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   11.350000] usbcore: registered new interface driver ftdi_sio
[   11.350000] usbserial: USB Serial support registered for FTDI USB Serial Device
[   11.360000] ftdi_sio 1-1.1:1.0: FTDI USB Serial Device converter detected
[   11.400000] usb 1-1.1: Detected FT232RL
[   11.400000] usb 1-1.1: Number of endpoints 2
[   11.400000] usb 1-1.1: Endpoint 1 MaxPacketSize 16384
[   11.410000] usb 1-1.1: Endpoint 2 MaxPacketSize 16384
[   11.410000] usb 1-1.1: Setting MaxPacketSize 64
[   11.430000] usb 1-1.1: FTDI USB Serial Device converter now attached to ttyUSB0
[   11.440000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.500000] usbcore: registered new interface driver pl2303
[   11.500000] usbserial: USB Serial support registered for pl2303
[   11.560000] ath: EEPROM regdomain: 0x0
[   11.560000] ath: EEPROM indicates default country code should be used
[   11.560000] ath: doing EEPROM country->regdmn map search
[   11.560000] ath: country maps to regdmn code: 0x3a
[   11.560000] ath: Country alpha2 being used: US
[   11.560000] ath: Regpair used: 0x3a
[   11.570000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   11.580000] cfg80211: Calling CRDA for country: US
[   11.580000] cfg80211: Regulatory domain changed to country: US
[   11.590000] cfg80211:  DFS Master region: FCC
[   11.590000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   11.600000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   11.610000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[   11.620000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[   11.630000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   11.630000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   11.640000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   19.980000] device eth0 entered promiscuous mode
[   20.470000] eth0: link up (100Mbps/Full duplex)
[   20.470000] br-lan: port 1(eth0) entered forwarding state
[   20.480000] br-lan: port 1(eth0) entered forwarding state
[   22.480000] br-lan: port 1(eth0) entered forwarding state


Using a North American Pool for NTP and Google NTP servers:
north-america.pool.ntp.org
time1.google.com
time2.google.com
time3.google.com


Thoughts?  Help?  Thanks for suggestions so far.  I'm still digging on my end.
newbie
Activity: 4
Merit: 0
June 25, 2014, 08:36:22 AM
try going here
http://downloads.canaan-creative.com/software/avalon2/latest/tl-wr703n-v1/20140526/
Posted from Bitcointa.lk - #5VdpO7W7cSpXTyNO

Thanks, I've applied that one with the same behavior, I Rolled back just in case it had compatibility concerns.  This just came from a few posts I was researching. 

One person thought they fixed it due to a problem communicating over 123 but I believe I have that open.  And I didn't need that earlier if that was the case because it was working, I ran the firmware update and it stopped working.

Kevsteelio
newbie
Activity: 36
Merit: 0
June 25, 2014, 12:39:04 AM
Warning:  New guy!

I picked up a 200 GHs Avalon that was running fine.  I've been working with it fine for a few months and I finally decided to upgrade the firmware.  Used the openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory-20140201 firmware package.

Since then it has been a nightmare.  CGMiner no longer makes any connection to my pools.  when looking in the CGMiner logs I see the following:

[Firmware Version] => 20140201
cgminer: 698d677
cgminer-openwrt-packages: 7a823a7
luci: 4544a03
Socket connect failed: Connection refused


The CGMiner page looks like the image here ftp://ftp.storagecraft.com/ava200ghs.png

I've dug through a bunch of posts across many areas.  your help and suggestions would be very welcome.
try going here
http://downloads.canaan-creative.com/software/avalon2/latest/tl-wr703n-v1/20140526/
Posted from Bitcointa.lk - #5VdpO7W7cSpXTyNO
newbie
Activity: 4
Merit: 0
June 25, 2014, 12:01:24 AM
Warning:  New guy!

I picked up a 200 GHs Avalon that was running fine.  I've been working with it fine for a few months and I finally decided to upgrade the firmware.  Used the openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory-20140201 firmware package.

Since then it has been a nightmare.  CGMiner no longer makes any connection to my pools.  when looking in the CGMiner logs I see the following:

[Firmware Version] => 20140201
cgminer: 698d677
cgminer-openwrt-packages: 7a823a7
luci: 4544a03
Socket connect failed: Connection refused


The CGMiner page looks like the image here http://ftp://ftp.storagecraft.com/ava200ghs.png

I've dug through a bunch of posts across many areas.  your help and suggestions would be very welcome.
Pages:
Jump to: