Topic: GekkoScience Terminus R606 750GH (up to 1TH) quiet miner, now shipping - page 3. (Read 11704 times)
September 07, 2020, 10:35:45 PM
my psu is 1000w and is running 2 R606's and an Apollo pulling just around 300w
September 07, 2020, 10:34:15 PM
If you're using a brick, take it easy. If you've got a decent PSU on the PCIe connector, well, just don't burn the miner up. I've had test units run almost 900MHz.
September 07, 2020, 07:46:04 PM
That sounds pretty good. I wouldn't go over 750Mhz though, per sidehacks suggestion.
September 07, 2020, 07:06:49 PM
The old versions I have are 4.11.1 363d879 and 7f04144
Likely what vh gave me with the demo a little over a year ago now. Looks the like the second version above after I took "--gekko-noboost" out of the batch file is moves up closer to 800Gh/s far 25min in.
Again, original demo usb 2.0 on my 10 year old laptop running windows10. freq 800, V setting 5.
Likely what vh gave me with the demo a little over a year ago now. Looks the like the second version above after I took "--gekko-noboost" out of the batch file is moves up closer to 800Gh/s far 25min in.
Again, original demo usb 2.0 on my 10 year old laptop running windows10. freq 800, V setting 5.
September 07, 2020, 04:33:45 PM
These R606's are the best he's got so far, but judging by each iteration of miner he produces the next will be a lot better (if he makes a 500w miner, which I hope he does as my space heater project isn't that efficient, even for a space heater 
)
) September 07, 2020, 04:33:19 PM
Which 500watt miner by sidehack are you referring to if you don't mind me asking. I am new to this type of hack of asics and would like to know if it is better than these terminus R606.
Regards to you MoparMiningLLC.
Regards to you MoparMiningLLC.
its just one that sidehack has mentioned as a possible project (same guy that did the terminus r606) - I do not think there is anything set in stone. I only stated that the psu will have enough spare wattage to power one if he does eventually do it.
September 07, 2020, 04:22:03 PM
The 1000 watt psu came today - currently running two R606's and 1 Apollo off of it - and still enough power for when Sidehack gets that 500 watt miner done...
Which 500watt miner by sidehack are you referring to if you don't mind me asking. I am new to this type of hack of asics and would like to know if it is better than these terminus R606.
Regards to you MoparMiningLLC.
September 07, 2020, 03:20:04 PM
Uh, no. That's on his Pi 4.
correct this is on raspberry pi 4
September 07, 2020, 03:08:20 PM
This is on windows10?
Uh, no. That's on his Pi 4.
With the latest cgminer I was only getting about 500+ Gh..
On the 85f build I was getting 736Ghs on P/L 4 at 562.5Mhz. Not too bad actually. That was on Win7.
September 07, 2020, 02:46:13 PM
getting just shy of 1 th/s on each on setting 6 and 715-730 mhz...
This is on windows10?
With the latest cgminer I was only getting about 500+ Gh. The older cgminers are on my laptop so I plugged it in there. Will give it. A few hours and see. I have a couple old versions. We’ll see what works best. On the laptop and maybe try that one on the desktop since it’s attached to the psu there.
September 07, 2020, 01:26:19 PM
getting just shy of 1 th/s on each on setting 6 and 715-730 mhz
September 07, 2020, 12:13:34 PM
I recall it running 800-900GH when I last had it running, I just don't have the batch file anymore. I do know it was running on cgminer 4.11.1 7f04144 at the time. Still yes, was very temperamental on windows 10.
That's not in the list of CGMiners supporting the R606. Did you get a special build?
The one that worked best for me on Win7 was a62385f, if I remember right. Never got to 900Ghs though.
September 07, 2020, 11:30:10 AM
I recall it running 800-900GH when I last had it running, I just don't have the batch file anymore. I do know it was running on cgminer 4.11.1 7f04144 at the time. Still yes, was very temperamental on windows 10.
September 06, 2020, 08:12:23 PM
yea it sucks on windows - I was averaging 745-750 gh/s - did not change any miner settings - moved it to linux on a raspberry pi 4 and its now at or just under 1 th/s for each of them. they run flawlessly.
September 06, 2020, 06:26:08 PM
By "windowx" I assume you mean Windblows 10. I'm pretty sure everyone abandoned that mess finally and went to the Pi 4.
I would set it to Power Level 4 at 550Mzh and let CGMiner tune it to whatever it will do and let it go. It will be less than 750Ghs, I'm pretty sure.
Good Luck
I would set it to Power Level 4 at 550Mzh and let CGMiner tune it to whatever it will do and let it go. It will be less than 750Ghs, I'm pretty sure.
Good Luck
September 06, 2020, 03:15:55 PM
Nice! I just pulled out my pc for dusting and added my r606 tester we got pre launch and have it up and running.
It's a windowx os, wondering what setting people are using on this os.
It's a windowx os, wondering what setting people are using on this os.
September 03, 2020, 05:26:11 PM
agreed! I have 2 R606's on my desk and a 1000 watt psu on it's way to power both - will have enough power left over to do the 500 watt miner, if you make it
and a 1000 watt psu on it's way to power both - will have enough power left over to do the 500 watt miner, if you make it The 1000 watt psu came today - currently running two R606's and 1 Apollo off of it - and still enough power for when Sidehack gets that 500 watt miner done
the miners are happily running.
August 28, 2020, 12:05:04 AM
A polite reminder that current sales fund future products.
August 27, 2020, 02:55:27 PM
I've got some ideas, yeah. Still figuring out which chip to use, but improving control systems is a separarate arm of development and so can be done anytime. May also have to beef the main regulator. Right now I've got like six other non-miner projects in progress so I can't really say when anything will be getting done, but I'd like to be shipping at least a new stick this calendary year.
Yes please!
August 27, 2020, 12:23:15 AM
I've got some ideas, yeah. Still figuring out which chip to use, but improving control systems is a separarate arm of development and so can be done anytime. May also have to beef the main regulator. Right now I've got like six other non-miner projects in progress so I can't really say when anything will be getting done, but I'd like to be shipping at least a new stick this calendary year.
Jump to: