Mini Review: I have a couple S4 Plus units in hand that I have been running for about an hour or so.
Getting about 2550 GHs on each one, running on a pool that is known to lose some hash rate.
Measured about 6.2 - 6.3 Amps / 12.5 Amps for the Pair on 220v (235v) = 1470 Watts Each at the Wall.
So I personally am getting about .57 Efficiency which is slightly better then advertised.
About the same sound / noise level of a normal S4, only hear the high pitch PSU fan if very close up.
I am getting some vibration noise, from both of them, which is unusual, as I never had before in any S4 Units.
Overall, Not Bad, A tad overpriced. People want the S6 with the new chips, this is something at least until then.
Anyhow I have them up for sale if anyone wants them shipped out today from New York.
Topic: ANTMINER S4+ Discussion and Support Thread - page 12. (Read 20111 times)
https://farm9.staticflickr.com/8751/17240307015_4fc7165728_o.jpg
nice patches on the right side! air quality control on the ''testing site'' is beautiful!
nice patches on the right side! air quality control on the ''testing site'' is beautiful!
That's the underside, pressed tight against the heatsink. You can see from the heatsink picture that those areas are fully enclosed and not exposed to the air what so ever.
You should know doggie you get yours free !
https://farm9.staticflickr.com/8751/17240307015_4fc7165728_o.jpg
nice patches on the right side! air quality control on the ''testing site'' is beautiful!
nice patches on the right side! air quality control on the ''testing site'' is beautiful!
That's the underside, pressed tight against the heatsink. You can see from the heatsink picture that those areas are fully enclosed and not exposed to the air what so ever.
https://farm9.staticflickr.com/8751/17240307015_4fc7165728_o.jpg
nice patches on the right side!
air quality control on the ''testing site'' is beautiful!
nice patches on the right side!
air quality control on the ''testing site'' is beautiful!
Hy dear Bitmain,
unfortunately the "new" S4+ has no significant improvement in power to hash ratio and on my personal opinion a decrease in attraction for home miners in Middle europe, US and other countries above €$0,15/kWH.
If i may post a wish for a S6 or S7, this would be 0,25W/GH and a noise level below 30db
Kind regards,
elrippo
unfortunately the "new" S4+ has no significant improvement in power to hash ratio and on my personal opinion a decrease in attraction for home miners in Middle europe, US and other countries above €$0,15/kWH.
If i may post a wish for a S6 or S7, this would be 0,25W/GH and a noise level below 30db
Kind regards,
elrippo
I don't know if I would agree with all of this. I think home miners are starting to look at 220/240 so I'm glad to see them jump into this level. It allows for a lot in future.
As far as .15 KWH you might look into hosting centers I think you will be able to get it cheaper. Also avoid I'm guessing a Europe vat depending on the location of hosting you choose.
I personally am a fan of hosting my hardware at a location that i have immediate access to, virtually as physically. Unfortunately other countries have a quite huge advantage in terms of power cost and taxiation.
If i remember wright, this is a community driven effort, and it should be possible, nearly possible for everyone to dedicate to it. With the current FIAT ratio and costs to mine, several countries if not continents have a disadvantage which can be partially compensated by technology.
Bitmain seems to drive this as a big player in the industrie and serves home miners, and before i write further, i really appreciate this, so i do not think that this is technically a issue, this is more a strategic and philosophic state.
I don´t have to mine at 220/2240 here in Middleurope with a rasing diff of 3%. It starts getting profitable above 335/340 for one year, maybe 18 months.
Bitmain, please treat the S4+ and it's users better than you did the S4's.
Hy dear Bitmain,
unfortunately the "new" S4+ has no significant improvement in power to hash ratio and on my personal opinion a decrease in attraction for home miners in Middle europe, US and other countries above €$0,15/kWH.
If i may post a wish for a S6 or S7, this would be 0,25W/GH and a noise level below 30db
Kind regards,
elrippo
unfortunately the "new" S4+ has no significant improvement in power to hash ratio and on my personal opinion a decrease in attraction for home miners in Middle europe, US and other countries above €$0,15/kWH.
If i may post a wish for a S6 or S7, this would be 0,25W/GH and a noise level below 30db
Kind regards,
elrippo
I don't know if I would agree with all of this. I think home miners are starting to look at 220/240 so I'm glad to see them jump into this level. It allows for a lot in future.
As far as .15 KWH in euros you might look into hosting centers I think you will be able to get it cheaper. Also avoid I'm guessing a Europe vat depending on the location of hosting you choose.
Hy dear Bitmain and dogie,
unfortunately the "new" S4+ has no significant improvement in power to hash ratio and on my personal opinion a decrease in attraction for home miners in Middle europe, US and other countries above €$0,15/kWH.
If i may post a wish for a S6 or S7, this would be 0,25W/GH and a noise level below 30db. Technically this should not be an issue for a legit company as bitmain is
Kind regards,
elrippo
unfortunately the "new" S4+ has no significant improvement in power to hash ratio and on my personal opinion a decrease in attraction for home miners in Middle europe, US and other countries above €$0,15/kWH.
If i may post a wish for a S6 or S7, this would be 0,25W/GH and a noise level below 30db. Technically this should not be an issue for a legit company as bitmain is
Kind regards,
elrippo
Hello all,
Bitmain has employed me to help liaise with the community and later provide technical support. They have done this in order to help provide:
1) timely technical support
2) provide better feedback (if I don't know, I can find out from the people within Bitmain who will)
3) provide product and sales input from you guys directly into the company. If something is going wrong, YOU can fix it
4) provide native English press releases - less ManderEnglish, more sense.
This is a paid position, however it will in no way affect my independence or freedom in being critical towards Bitmain outside of this thread. My contract specifically stipulates:
This means I won't sit here and reply to every post saying Bitmain is a scam, don't buy from Bitmain etc etc, in this thread. It does NOT prohibit me from saying that in my own threads, if that is what I believe. It also has absolutely no impact on their rating in the Manufacturer trustwothiness thread [in which Bitmain just went down 10 points].
Bitmain has employed me to help liaise with the community and later provide technical support. They have done this in order to help provide:
1) timely technical support
2) provide better feedback (if I don't know, I can find out from the people within Bitmain who will)
3) provide product and sales input from you guys directly into the company. If something is going wrong, YOU can fix it
4) provide native English press releases - less ManderEnglish, more sense.
This is a paid position, however it will in no way affect my independence or freedom in being critical towards Bitmain outside of this thread. My contract specifically stipulates:
Quote
Dogie will speak on behalf of BITMAIN and will not criticize BITMAIN in these threads. Dogie still reserves the right to criticize BITMAIN in his other threads. Both parties acknowledge that this relationship has no impact whatsoever on BITMAIN’s rating or standing in “Dogie’s ‘Manufacturer Trustworthiness” thread.
This means I won't sit here and reply to every post saying Bitmain is a scam, don't buy from Bitmain etc etc, in this thread. It does NOT prohibit me from saying that in my own threads, if that is what I believe. It also has absolutely no impact on their rating in the Manufacturer trustwothiness thread [in which Bitmain just went down 10 points].
FAQ and Technical Support
Dogie's comprehensive setup guide in super HD!
Configuration
FAQ
Dogie's comprehensive setup guide in super HD!
Configuration
Quote
Wiring:
Configuration:
- Plug in a power cable from the AntMiner to the mains.
- Plug in an ethernet cable from the AntMiner to you router.
Configuration:
- The unit will automatically power on when you provide it power.
- Make sure that your router's DHCP table is turned on. You can assume it is already on if you have a typical router.
- Using a browser, navigate to your router and find the IP it has assigned the S4+ and navigate to that IP.
- Login using "root" as both the username and password.
- Navigate to the page Status -> Miner Configuration. Enter your pool information in the below format. Click "Save & Apply".
- Navigate to the page "Miner Status" to check mining has started.
FAQ
Quote
 | |
| Under ASIC status, one chip is always an "x"? | Will the miner ever beep? |
| - There is a faulty chip - nothing we can do. Hash rate will be affected by ~1%. | - No, the beeper was removed on the S4+. The Miner configuration option of "Beeper Ringing" does not do anything. |
Under ASIC status, one row is almost all "x"es? | I can connect to the Antminer but the status page is blank? |
| - One board may have dropped temporarily. Try hard resetting the miner by powering it on and off. | - You may have entered an incorrect miner setting causing cgminer to crash. Post a screenshot of your configuration page if still unsure. |
How do I reset settings to default? | What temperatures should I aim for? |
| - Use a paper clip to press the reset button - located next to the LEDs and ethernet connector - down for 5-10 seconds. The miner will then reset with stock settings. | - Try and achieve <75°C for best hash rates, and <85°C for long lifetimes. Temperatures over 90°C will cause an overheat warning to be issued and over 95°C will cause the miner to stop. |
How do I change the login password? | Where can I get the latest firmware? |
| - Navigate to System -> Administration. Enter the current password and enter your new one twice. | - Download from Bitmain's site. |
What is the SSH login? | How can I tell what firmware version I have now? |
| - Username "root", password "admin". | - Navigate to System -> Overview and look at "File System Version". |
What do the LEDs on the front mean? | How do I install the latest firmware? |
| - The green LED will flash when mining, and the red LED will remain on while in an error or overheat state. | - Download firmware as above. Navigate to System -> Upgrade and click "browse". Select the downloaded file and click "Flash image". Do NOT interrupt this process or you will brick the unit. |
Jump to: